Raritan 1700 Series Water Heater Heating Element User Manual

Introduction

This manual provides essential information for the proper installation, operation, and maintenance of your Raritan 1700 Series Water Heater Heating Element with Gasket, 120V Screw-In Type. Please read these instructions carefully before proceeding with installation or use to ensure safe and efficient performance.

The Raritan 1700 Series Heating Element is designed for use in Raritan water heaters, providing reliable heating for marine applications. It includes a gasket for a secure, watertight seal.

Product Overview

Figure 1: Raritan 1700 Series Water Heater Heating Element. This image shows the screw-in heating element with its two heating rods and the base where electrical connections are made, along with the included gasket.

The Raritan 1700 Series Heating Element is a screw-in type, operating at 120V. It is supplied with a gasket to ensure a proper seal when installed into the water heater tank. This element is a critical component for heating water within compatible Raritan water heater systems.

Safety Information

Always disconnect power to the water heater before attempting any installation, maintenance, or troubleshooting. Failure to do so can result in electric shock, serious injury, or death.

• Ensure the water heater tank is completely drained before removing or installing the heating element.
• Use appropriate tools and follow all local electrical codes and regulations.
• If you are unsure about any part of the installation or repair process, consult a qualified electrician or marine technician.
• Do not operate the heating element in a dry tank.

Setup and Installation

1. Preparation:
   • Turn off all power to the water heater at the main breaker.
   • Close the cold water supply valve to the water heater.
   • Open a hot water faucet in your vessel to relieve pressure and drain the water heater. Use the drain valve on the water heater to completely empty the tank.
2. Element Removal (if replacing):
   • Disconnect the electrical wires from the old heating element terminals. Note their positions for reinstallation.
   • Using a specialized heating element wrench or a large socket (often 1 1/2 inches or similar, verify size for your specific water heater model), carefully unscrew the old heating element.
   • Remove the old element and gasket.
3. Element Installation:
   • Ensure the heating element opening on the water heater tank is clean and free of debris.
   • Place the new gasket onto the base of the new Raritan heating element.
   • Carefully thread the new heating element into the opening. Ensure it is not cross-threaded.
   • Tighten the element firmly with the wrench. Do not overtighten, but ensure a snug, watertight seal.
4. Electrical Connection:
   • Reconnect the electrical wires to the new heating element terminals as they were on the old element. Ensure connections are secure.
   • Verify that all wiring is correct and insulated.
5. Refilling and Testing:
   • Close the drain valve on the water heater.
   • Open the cold water supply valve to the water heater.
   • Allow the tank to fill completely. Open a hot water faucet until water flows freely and all air is purged from the tank.
   • Check for any leaks around the new heating element. If leaks are present, tighten the element slightly more.
   • Once the tank is full and no leaks are detected, restore power to the water heater at the main breaker.

Operating Instructions

Once installed and power is restored, the Raritan 1700 Series Heating Element will begin to heat the water in the tank. The water heater's thermostat controls the water temperature. This heating element is designed to work seamlessly with your existing Raritan water heater's control system.

• Ensure the water heater is always full of water when the heating element is powered on.
• Refer to your specific Raritan water heater manual for details on adjusting temperature settings or other operational features.

Maintenance

Regular maintenance helps ensure the longevity and efficiency of your heating element and water heater system.

• Annual Inspection: Annually inspect the heating element for signs of corrosion or mineral buildup. In areas with hard water, mineral deposits can accumulate on the element, reducing efficiency.
• Anode Rod Check: While not directly part of the heating element, the anode rod in your water heater protects the tank from corrosion. Check and replace it as recommended by your water heater's manufacturer, typically every 1-3 years.
• Draining and Flushing: Periodically drain and flush your water heater tank to remove sediment buildup, which can also impact heating element performance and tank life.
• Gasket Integrity: If the heating element is ever removed, always replace the gasket to ensure a proper seal upon reinstallation.

Troubleshooting

For issues not listed here, or if troubleshooting steps do not resolve the problem, contact a qualified technician or Raritan customer support.

Specifications

Warranty and Support

For specific warranty information regarding your Raritan 1700 Series Water Heater Heating Element, please refer to the documentation provided with your original Raritan water heater or contact Raritan directly. Warranty terms may vary.

For technical support or further assistance, please visit the official Raritan website or contact their customer service department. Contact information can typically be found on the manufacturer's website or in your water heater's original manual.

Note: This heating element is a replacement part. Its warranty is typically covered under the terms for replacement parts as defined by Raritan.