1. Introduction
Thank you for purchasing the ONKYO CD Receiver CR-T2, a core component of the X-T2 mini component system. This unit is designed to provide high-quality audio playback from CDs and radio broadcasts (AM/FM). This manual provides essential information for the proper setup, operation, and maintenance of your system. Please read it thoroughly before using the unit and retain it for future reference.
Note: While the overall product system may be referred to as a "CD/MD Tuner Amplifier System," the CR-T2 unit itself primarily functions as a CD receiver and tuner. MD (MiniDisc) functionality typically requires a separate, compatible MD component connected to this receiver.
2. Important Safety Information
- Power Source: Connect the unit only to an AC outlet of the voltage specified on the rear panel.
- Ventilation: Ensure adequate ventilation. Do not block ventilation openings. Avoid placing the unit on soft surfaces that may block vents.
- Water and Moisture: Do not expose the unit to rain or moisture. Do not place objects filled with liquids, such as vases, on the unit.
- Heat: Keep the unit away from heat sources such as radiators, heat registers, stoves, or other heat-producing appliances.
- Cleaning: Unplug the unit from the wall outlet before cleaning. Use a dry cloth only.
- Servicing: Do not attempt to service this product yourself. Refer all servicing to qualified service personnel.
- Disc Handling: Handle CDs by their edges. Avoid touching the playing surface.
3. Setup Guide
3.1 Unpacking
Carefully remove the unit and all accessories from the packaging. Retain the packaging materials for future transport or storage.
3.2 Connecting Speakers
Connect your speakers to the speaker terminals on the rear of the CR-T2 unit. Ensure correct polarity (+ to + and - to -) for each speaker. Incorrect polarity can result in poor sound quality.
- Use speaker cables of appropriate gauge for your speakers and cable length.
- Strip approximately 10-15 mm (3/8 - 5/8 inches) of insulation from the ends of the speaker wires.
- Twist the bare wires tightly to prevent short circuits.
- Connect the right speaker to the "RIGHT" terminals and the left speaker to the "LEFT" terminals.
3.3 Connecting Antennas
For optimal radio reception, connect the supplied AM loop antenna and FM wire antenna to their respective terminals on the rear panel.
- FM Antenna: Connect the supplied FM wire antenna to the FM antenna terminal. Extend the wire fully for better reception.
- AM Antenna: Assemble the AM loop antenna and connect its two wires to the AM antenna terminals. Position the AM loop antenna away from the main unit and other electronic devices to minimize interference.
3.4 Connecting Other Components
If you wish to connect additional audio components, such as an external MD player, cassette deck, or other audio sources, use appropriate RCA audio cables to connect their output jacks to the corresponding input jacks on the CR-T2 unit.
Refer to the rear panel diagram in your full user manual for specific input/output locations.
3.5 Power Connection
After all other connections are made, plug the power cord into a suitable AC wall outlet.
4. Operating Instructions
Figure 4.1: Front Panel of the ONKYO CD Receiver CR-T2. This image displays the front panel of the Onkyo CR-T2 CD Receiver. Visible elements include the 'ONKYO' logo, the 'I/O ON/STANDBY' power button, 'CD RECEIVER CR-T2' model designation, and the digital display showing 'AM 1179 kHz'. Below the display, 'STANDBY' and 'DISPLAY' buttons are also visible.
4.1 Basic Power On/Off
To turn the unit on or off (standby mode), press the I/O ON/STANDBY button located on the front panel (refer to Figure 4.1).
4.2 CD Playback
- Press the CD input selector button to choose the CD source.
- Press the OPEN/CLOSE button (usually near the CD tray) to open the CD tray.
- Place a CD with the label side up into the tray.
- Press OPEN/CLOSE again to close the tray.
- Press the PLAY button to start playback.
- Use STOP, PAUSE, SKIP (forward/backward) buttons for disc control.
4.3 Tuner Operation (AM/FM)
- Press the TUNER input selector button to select the radio source.
- Press the BAND button to switch between FM and AM bands.
- Use the TUNING buttons (up/down arrows) to manually tune to a station.
- For automatic tuning, press and hold the TUNING buttons until the unit starts scanning. It will stop at the next strong station.
- To preset stations, tune to the desired station, then press the MEMORY button followed by a preset number button.
4.4 Volume Control
Adjust the listening volume using the VOLUME knob on the front panel or the corresponding buttons on the remote control.
4.5 Input Selection
Press the respective input selector buttons (e.g., CD, TUNER, MD/LINE IN) on the front panel or remote control to switch between connected audio sources.
4.6 Display Information
The front panel display shows information such as the current source, radio frequency (e.g., AM 1179 kHz as seen in Figure 4.1), track number, and playback time for CDs. Press the DISPLAY button to cycle through different display modes or information.
5. Maintenance
5.1 Cleaning the Unit
- Before cleaning, disconnect the power cord from the wall outlet.
- Use a soft, dry cloth to wipe the exterior surfaces of the unit.
- For stubborn dirt, slightly dampen the cloth with water or a mild, non-abrasive cleaner. Do not use harsh chemicals, solvents, or abrasive cleaning pads.
- Avoid spraying liquids directly onto the unit.
5.2 Care of CDs
- Handle CDs by their edges to prevent fingerprints and scratches on the playing surface.
- Store CDs in their cases when not in use.
- If a CD is dirty, wipe it gently from the center outwards with a soft, lint-free cloth. Do not use abrasive cleaners or solvents.
6. Troubleshooting
Before contacting customer support, please refer to the following common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| No power | Power cord not connected; Power outlet faulty | Ensure power cord is securely plugged in; Try a different outlet. |
| No sound | Volume too low; Incorrect input selected; Speakers not connected properly | Increase volume; Select correct input source; Check speaker connections and polarity. |
| CD does not play | CD inserted incorrectly; CD is dirty or scratched; Disc format not supported | Insert CD correctly (label side up); Clean or replace CD; Ensure it's an audio CD. |
| Poor radio reception | Antenna not connected or positioned poorly; Interference from other devices | Connect and adjust antenna position; Move unit away from other electronics. |
7. Specifications
Specifications are subject to change without notice for product improvement.
- Model: ONKYO CR-T2 (Part of X-T2 System)
- Functions: CD Player, AM/FM Tuner, Amplifier
- Power Output: (Specific wattage not provided in input, typically found in full manual) e.g., 20W + 20W (6 ohms, 1 kHz, 10% THD)
- Frequency Response: (Specific range not provided in input) e.g., 20 Hz – 20 kHz (CD)
- Tuner Frequency Range: FM: 87.5 MHz – 108.0 MHz; AM: 522 kHz – 1629 kHz
- Power Supply: AC 100V, 50/60 Hz (Japan model)
- Power Consumption: (Specific value not provided in input) e.g., 45 W
- Dimensions (W x H x D): (Specific values not provided in input) e.g., 205 x 100 x 350 mm
- Weight: 5230 grams (5.23 kg)
8. Warranty and Customer Support
ONKYO products are manufactured to the highest quality standards. For warranty information, please refer to the separate warranty card included with your purchase or visit the official ONKYO website for details specific to your region.
For technical assistance, service, or inquiries, please contact your authorized ONKYO dealer or the ONKYO customer support center in your country. Please have your model number (X-T2) and serial number ready when contacting support.
You can find more information and support resources on the official Onkyo website: www.onkyo.com
