1. Introduction
Thank you for choosing the Locksmart LC63720 Ignition Lock Cylinder. This product is designed as a direct Original Equipment (OE) replacement, ensuring OE quality fit, form, and function for your automotive ignition system. Manufactured with advanced quality materials, it provides durability and reliability. This manual provides essential information for the safe and correct installation, operation, and maintenance of your new ignition lock cylinder.
2. Product Overview
The Locksmart LC63720 Ignition Lock Cylinder is a critical component of your vehicle's starting system. It includes the lock cylinder unit and corresponding keys. The unit features 100% new OE-quality seals and cups to prevent leakage and ensure reliable performance.

Figure 2.1: The Locksmart LC63720 Ignition Lock Cylinder with keys inserted, showing the main body and keyhole.

Figure 2.2: Front view of the Locksmart LC63720 Ignition Lock Cylinder alongside the two included keys.
3. Safety Information
Always prioritize safety when working on your vehicle. Improper installation can lead to vehicle damage or personal injury.
- Disconnect Battery: Before beginning any work, always disconnect the vehicle's negative battery terminal to prevent electrical shorts and accidental airbag deployment.
- Professional Installation: If you are not confident in your mechanical abilities, it is highly recommended to seek professional installation from a qualified automotive technician.
- Use Proper Tools: Ensure you have the correct tools for the job to avoid damaging components.
- Read Vehicle Service Manual: Consult your vehicle's specific service manual for detailed instructions on removing and installing the ignition lock cylinder for your make and model.
4. Setup and Installation
This section provides general steps for replacing an ignition lock cylinder. Specific procedures may vary by vehicle. Always refer to your vehicle's service manual.
- Prepare Vehicle: Park the vehicle on a level surface, engage the parking brake, and turn off the engine. Disconnect the negative battery terminal.
- Access Steering Column: Carefully remove any necessary steering column covers or trim panels to gain access to the ignition switch and lock cylinder assembly. This often involves removing screws and gently prying plastic clips.
- Remove Old Lock Cylinder:
- Insert the old key into the existing lock cylinder and turn it to the 'ACC' (Accessory) or 'ON' position, as specified by your vehicle's manual.
- Locate the small release pin or button on the ignition lock cylinder housing. This is typically a small hole where a pick or thin tool can be inserted.
- While holding the key in the correct position, depress the release pin. The lock cylinder should then slide out of its housing.
- If the old key is lost or broken, specialized tools or drilling may be required. Professional assistance is recommended in such cases.
- Install New Lock Cylinder:
- Insert one of the new keys into the Locksmart LC63720 cylinder.
- Turn the key to the 'ACC' or 'ON' position, matching the position required for removal.
- Align the new lock cylinder with the opening in the ignition housing and gently push it into place until it clicks or locks securely. Ensure the release pin engages properly.
- Test the cylinder's movement with the key through all positions (OFF, ACC, ON, START) to ensure smooth operation before reassembly.
- Reassemble and Test: Reinstall any removed steering column covers and trim panels. Reconnect the negative battery terminal. Test the ignition system to ensure the vehicle starts and operates correctly.

Figure 4.1: Side view of the lock cylinder with a key inserted, illustrating the internal components that engage with the ignition switch.
5. Operation
Operating the Locksmart LC63720 Ignition Lock Cylinder is straightforward:
- Insert Key: Gently insert the provided key into the keyhole of the ignition lock cylinder. Do not force the key.
- Key Positions: Turn the key clockwise to cycle through the ignition positions:
- OFF/LOCK: Engine off, steering wheel locked (if applicable). Key can be removed.
- ACC (Accessory): Powers accessories like radio, without turning on the engine.
- ON/RUN: All electrical systems are powered, engine is ready to start or is running.
- START: Engages the starter motor to crank the engine. Release the key once the engine starts; it will spring back to the 'ON' position.
- Remove Key: To remove the key, ensure the cylinder is in the 'OFF/LOCK' position.
6. Maintenance
The Locksmart LC63720 Ignition Lock Cylinder is designed for long-lasting performance with minimal maintenance. Follow these guidelines:
- Keep Keyhole Clean: Avoid introducing foreign objects into the keyhole. If debris accumulates, use a specialized lock lubricant or compressed air to clear it.
- Avoid Forcing Keys: Never force a key into the cylinder or attempt to turn a bent or damaged key. This can damage the internal tumblers.
- Lubrication: If the key feels stiff, apply a small amount of graphite-based lock lubricant into the keyhole. Avoid oil-based lubricants as they can attract dirt.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Key does not turn smoothly or gets stuck. | Debris in keyhole, worn key, steering wheel lock engaged. | Try wiggling the steering wheel while turning the key. Clean keyhole with compressed air or lock lubricant. Use a new, undamaged key. |
| Engine does not start after turning key to 'START'. | Battery issue, starter motor issue, wiring problem, immobilizer system. | Check battery terminals and charge. This issue is likely not related to the lock cylinder itself. Consult a mechanic. |
| Key cannot be removed from cylinder. | Cylinder not fully in 'OFF/LOCK' position, transmission not in 'Park' (for automatics). | Ensure the key is fully turned to the 'OFF/LOCK' position. For automatic transmissions, ensure the gear selector is firmly in 'Park'. |
If troubleshooting steps do not resolve the issue, contact Locksmart customer support or a qualified automotive technician.
8. Specifications
- Model Number: LC63720
- Brand: Locksmart
- Lock Type: Pin Tumbler
- Material: Metal
- Recommended Uses: Automotive
- Included Components: 1 Ignition Lock Cylinder, Keys, Mounting Hardware
- Manufacturer: Standard Motor Products
9. Warranty and Support
For warranty information and customer support regarding your Locksmart LC63720 Ignition Lock Cylinder, please refer to the documentation provided with your purchase or visit the official Locksmart website. You may also contact their customer service directly for assistance with product inquiries, technical support, or warranty claims.