InSinkErator F-C1100C Cold Water Dispenser Faucet Instruction Manual

1. Introduction

Thank you for choosing the InSinkErator F-C1100C Cold Water Dispenser Faucet. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your new faucet. The F-C1100C is designed to deliver cold drinking water directly at your kitchen sink when paired with a compatible InSinkErator cold water tank, such as the CWT-00 model. Its elegant chrome finish and high-arching spout complement various kitchen decors.

2. Safety Information

Please read all instructions carefully before installing or using this product. Failure to follow these instructions may result in property damage or personal injury.

• Always turn off the main water supply before beginning any installation or maintenance.
• Ensure all connections are secure and leak-free before restoring water supply.
• This faucet is designed for cold water dispensing only. Do not connect to a hot water supply.
• Professional installation is recommended if you are unfamiliar with plumbing procedures.
• Keep children away from the installation area.

3. Package Contents

Verify that all components are present before beginning installation:

• InSinkErator F-C1100C Cold Water Dispenser Faucet (Chrome)
• Mounting hardware (washers, nuts, etc.)
• Connection tubing/hoses
• Installation instructions (this manual)

Figure 1: InSinkErator F-C1100C Cold Water Dispenser Faucet. This image displays the InSinkErator F-C1100C cold water dispenser faucet. It features a high-arching spout and a single lever handle, all in a polished chrome finish. The design is transitional, suitable for various kitchen decors.

4. Specifications

5. Installation

This faucet requires a standard single-hole deck mount installation. It is designed to connect to a separate cold water tank (e.g., InSinkErator CWT-00) for chilled water delivery. Refer to the cold water tank's instruction manual for its specific installation requirements.

Tools and Materials (Not Included):

• Adjustable wrench
• Phillips head screwdriver
• Basin wrench (optional, for tight spaces)
• Plumber's putty or silicone sealant
• Teflon tape
• Drill (if creating a new mounting hole)

Installation Steps:

1. Prepare the Mounting Hole: Ensure a standard 1-3/8 inch (35mm) diameter hole is available on your sink or countertop. If drilling a new hole, follow the sink or countertop manufacturer's instructions.
2. Mount the Faucet:
   • Apply a thin bead of plumber's putty or silicone sealant around the base of the faucet.
   • Insert the faucet shank through the mounting hole.
   • From underneath the sink, slide the rubber washer, then the metal washer, and finally thread the mounting nut onto the faucet shank.
   • Hand-tighten the nut, then use a basin wrench or adjustable wrench to secure it firmly, ensuring the faucet is properly aligned. Do not overtighten.
3. Connect Water Lines:
   • Connect the faucet's cold water inlet line to the outlet of your InSinkErator cold water tank (e.g., CWT-00). Refer to the tank's manual for specific connection points.
   • Use Teflon tape on threaded connections to ensure a watertight seal.
   • Ensure all connections are hand-tight, then tighten an additional 1/4 to 1/2 turn with a wrench.
4. Check for Leaks:
   • Slowly turn on the main water supply.
   • Inspect all connections for any signs of leaks. Tighten connections as necessary.
   • Allow water to run through the faucet for a few minutes to flush out any debris.

6. Operation

The InSinkErator F-C1100C faucet is designed for simple, hands-free operation to dispense cold water.

• Dispensing Cold Water: Gently push the lever handle backward (away from the spout) to activate the cold water flow. The lever is designed to stay on, providing continuous flow without needing to hold it.
• Stopping Water Flow: Push the lever handle forward (towards the spout) to stop the water flow.
• Spout Swivel: The high-arching spout can swivel for greater convenience, allowing you to direct the water flow as needed.

7. Maintenance

Proper care and maintenance will ensure the longevity and appearance of your InSinkErator F-C1100C faucet.

• Cleaning the Finish: Clean the chrome finish regularly with a soft, damp cloth and mild soap. Rinse thoroughly and dry with a soft cloth to prevent water spots.
• Avoid Harsh Cleaners: Do not use abrasive cleaners, scouring pads, ammonia-based cleaners, or cleaners containing bleach, acids, or alcohol, as these can damage the finish.
• Aerator Maintenance: If water flow becomes restricted, the aerator at the tip of the spout may be clogged. Unscrew the aerator, clean any debris, and rinse it before reattaching.
• Periodic Inspection: Periodically check all connections under the sink for any signs of leaks or corrosion.

8. Troubleshooting

If you encounter issues with your F-C1100C faucet, refer to the following common problems and solutions:

9. Warranty and Support

For detailed warranty information, please refer to the documentation included with your product or visit the official InSinkErator website. If you require technical assistance or replacement parts, please contact InSinkErator customer support.

You can find more information and support resources by visiting the InSinkErator Store on Amazon.