Makita 6723DW Cordless Screwdriver Instruction Manual

1. Important Safety Instructions

Read all safety warnings and instructions before operating this power tool. Failure to follow the warnings and instructions may result in electric shock, fire, and/or serious injury. Save all warnings and instructions for future reference.

General Power Tool Safety

• Work Area Safety: Keep work area clean and well lit. Cluttered or dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
• Electrical Safety: Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges, and refrigerators.
• Personal Safety: Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication. Always wear eye protection.
• Power Tool Use and Care: Do not force the power tool. Use the correct power tool for your application. Do not use the power tool if the switch does not turn it on and off. Disconnect the plug from the power source and/or remove the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools.

2. Product Overview

The Makita 6723DW is a compact and versatile cordless screwdriver designed for various fastening applications. It features a 4.8V Ni-Cad battery, an adjustable hinged handle for ergonomic use, an integrated LED job light, and forward/reverse modes.

Components Included:

• Makita 6723DW Cordless Screwdriver
• Charger (Model: TP00000188)
• 80-Piece Bit Set
• Plastic Carrying Case

3. Setup

3.1 Charging the Battery

1. Ensure the screwdriver's power switch is in the "OFF" position.
2. Connect the charger (TP00000188) to a standard electrical outlet.
3. Insert the screwdriver's charging port into the charger.
4. Allow the battery to charge completely. For the first charge, it is recommended to charge for approximately 5 hours. Subsequent charges typically take around 3 hours.
5. Important: This tool uses a Ni-Cad battery. To maximize battery life and prevent memory effect, fully discharge the battery before recharging it.

3.2 Installing/Changing Screwdriver Bits

1. Ensure the screwdriver is turned off.
2. Select the appropriate bit from the 80-piece bit set for your application.
3. Insert the bit firmly into the screwdriver's bit holder until it clicks into place.
4. To remove a bit, pull it straight out from the bit holder.

3.3 Adjusting the Handle

The Makita 6723DW features an adjustable hinged handle, allowing you to switch between a straight and pistol-grip configuration for improved access and comfort.

1. To adjust the handle, firmly grasp both sections of the handle.
2. Gently pivot the handle at the hinge point until it locks into the desired straight or angled position.
3. Ensure the handle is securely locked before operation.

4. Operating Instructions

4.1 Powering On/Off and Direction Control

The screwdriver features a single switch for power control and direction selection.

• To operate in Forward mode (for driving screws), push the switch to the left.
• To operate in Reverse mode (for removing screws), push the switch to the right.
• To turn the tool OFF, ensure the switch is in the center position.

4.2 Using the LED Job Light

The integrated LED job light illuminates the work area for improved visibility.

• The LED light has an independent on/off switch. Locate the small button near the bit holder.
• Press the button once to turn the LED light ON.
• Press the button again to turn the LED light OFF.

4.3 General Operation Tips

• Apply firm, steady pressure to the screwdriver to prevent cam-out (the bit slipping out of the screw head).
• Do not over-tighten screws. The tool provides 40 in.lbs (4.5 Nm) of maximum torque.
• For delicate materials, start with a pilot hole to prevent splitting.

5. Maintenance

5.1 Cleaning

• Always disconnect the charger and ensure the tool is off before cleaning.
• Wipe the tool with a clean, damp cloth. Do not use harsh chemicals or abrasive cleaners.
• Keep ventilation openings clear of dust and debris to prevent overheating.

5.2 Battery Care and Storage

• As this tool uses a Ni-Cad battery, always fully discharge the battery before recharging to prevent memory effect.
• Store the screwdriver and battery in a cool, dry place, away from direct sunlight and extreme temperatures.
• For long-term storage, it is recommended to store the battery in a discharged state.

5.3 Bit Set Care

• Keep the bits clean and free of rust. A light coating of oil can help prevent corrosion.
• Store bits in the provided carrying case to keep them organized and protected.

6. Troubleshooting

7. Specifications

8. Warranty and Support

For information regarding the product warranty, please refer to the warranty card included with your purchase or visit the official Makita website. For technical support, replacement parts, or service inquiries, please contact Makita customer service directly.

You can find contact information for Makita customer service on their official website: Makita Contact Us