SAMSON RS15HD

Samson Resound RS15HD 15" 2-Way Passive PA Cabinet

Model: RS15HD (02-06-004)

Introduction

The Samson Resound RS15HD is a high-performance 15-inch 2-way passive PA cabinet designed for professional audio applications. This speaker cabinet delivers powerful, full-range sound suitable for various venues, from live performances to houses of worship. Its robust construction ensures durability and consistent performance.

Key Features

Two-way passive PA speaker cabinet
600 watt program power handling @ 8 ohms
Custom designed 15-inch low frequency driver
1.5-inch titanium compression driver
Dual 1/4-inch and Speakon connections for versatile connectivity

Product Overview

Figure 1: Front view of the Samson Resound RS15HD PA Cabinet. This image displays the robust black cabinet with a full metal grille protecting the 15-inch low-frequency driver and the high-frequency compression driver. The Samson logo is prominently displayed at the bottom center of the grille.

Setup Guide

Follow these steps to properly set up your Samson Resound RS15HD PA Cabinet:

Placement: Position the speaker on a stable, flat surface or a compatible speaker stand. Ensure the speaker is placed in a location that allows for optimal sound dispersion and avoids obstructions.
Connectivity: Connect your audio source (e.g., amplifier, mixer) to the RS15HD using high-quality speaker cables. Utilize either the 1/4-inch or Speakon connections on the rear panel. Ensure secure connections to prevent signal loss or damage.
Impedance Matching: Verify that the impedance of your amplifier matches the 8-ohm impedance of the RS15HD cabinet. Mismatched impedance can lead to poor performance or damage to your equipment.
Initial Power-Up: Before powering on your amplifier, ensure all volume controls are set to their minimum. Power on the amplifier, then slowly increase the volume to a desired listening level.

Important: Always ensure your amplifier is turned off before making any connections to the speaker cabinet.

Operating Instructions

The Samson Resound RS15HD is a passive speaker, meaning it requires an external amplifier to operate. Proper operation involves managing the amplifier's output and monitoring sound levels.

Volume Control: Adjust the volume primarily from your amplifier or mixer. Avoid pushing the amplifier into clipping (distortion), as this can damage the speaker.
Equalization: Use the equalizer on your mixer or amplifier to fine-tune the sound. The RS15HD is designed for a balanced frequency response, but minor adjustments may be needed for different acoustic environments.
Monitoring: Listen for any signs of distortion or stress from the speaker. If distortion occurs, reduce the input level or amplifier volume immediately.
Daisy-Chaining: If connecting multiple passive speakers, ensure the total impedance presented to the amplifier is within its safe operating range. Consult your amplifier's manual for specific guidelines.

Maintenance and Care

To ensure the longevity and optimal performance of your RS15HD PA Cabinet, follow these maintenance guidelines:

Cleaning: Use a soft, dry cloth to clean the exterior of the cabinet. Do not use abrasive cleaners or solvents, as they may damage the finish.
Storage: When not in use, store the speaker in a dry, cool environment, away from direct sunlight and extreme temperatures.
Protection: Protect the speaker from physical impact and moisture. Consider using a protective cover during transport or storage.
Inspection: Periodically inspect the speaker grille, connections, and cabinet for any signs of wear or damage. Address any issues promptly.

Troubleshooting

Problem	Possible Cause	Solution
No Sound Output	Loose or incorrect cable connections. Amplifier not powered on or volume too low. Input source issue.	Check all speaker and input cables; ensure they are securely connected. Verify amplifier power and increase volume gradually. Test with a different audio source.
Distorted Sound	Amplifier clipping (overdriving). Incorrect impedance matching. Damaged speaker component.	Reduce amplifier volume or input gain. Ensure amplifier impedance matches speaker (8 ohms). Contact Samson support for service if distortion persists at normal levels.
Intermittent Sound	Faulty cable. Loose connection.	Replace speaker cables. Check and secure all connections.

Technical Specifications

Model Name	RS15HD
Item Model Number	02-06-004
Speaker Type	Passive PA Speaker Cabinet
Speaker Size	15 Inches (Low Frequency Driver)
High Frequency Driver	1.5-inch Titanium Compression Driver
Program Power Handling	600 Watts
Impedance	8 Ohm
Connections	Dual 1/4-inch and Speakon
Cabinet Construction	All-plywood
Item Weight	44.5 pounds
Brand	SAMSON
UPC	809164008637

Warranty and Support

For detailed warranty information and technical support, please refer to the official Samson website or contact Samson customer service directly. Keep your purchase receipt as proof of purchase for warranty claims.

Samson Technologies Contact Information:

Website: www.samsontech.com
Support: Refer to the support section on the official website for FAQs, downloads, and contact options.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.