Introduction
Thank you for choosing the Hogue Inc. Hunting Grip for your S&W 1006/4506 Series firearm. This Coco Bolo grip is designed to enhance the ergonomics and aesthetics of your handgun, providing a secure and comfortable hold. This manual provides essential information for the proper installation, care, and maintenance of your new grip.
Important Safety Information
WARNING: Always ensure your firearm is unloaded and safe before attempting any installation, maintenance, or handling procedures. Follow all firearm safety rules. If you are unsure about any step, consult a qualified gunsmith. Improper installation can lead to malfunction or injury.
- Always verify the firearm is unloaded before beginning work.
- Wear appropriate eye protection.
- Keep fingers away from the trigger guard during installation.
- Store firearms and accessories securely and out of reach of children.
Package Contents
Please verify that all components are present before proceeding with installation:
- 1 x Hogue Inc. Hunting Grip (Coco Bolo) for S&W 1006/4506 Series
- (Any included screws or hardware, if applicable - assuming standard grip screws are used)
Note: Grip screws are typically reused from your existing grips or purchased separately if needed.
Installation Instructions
Follow these steps carefully to install your new Hogue Coco Bolo grip:
- Ensure Firearm is Safe: Double-check that your S&W 1006/4506 Series firearm is unloaded and the chamber is clear. Remove the magazine.
- Remove Old Grips: Using an appropriate screwdriver, carefully unscrew and remove the existing grip panels from both sides of the firearm frame. Keep the screws in a safe place.
- Position New Grips: Align the Hogue Coco Bolo grip panels with the screw holes on the firearm frame. Ensure the panels sit flush against the frame.
- Secure Grips: Insert the grip screws (either the original ones or new compatible screws) into the holes and gently tighten them. Do not overtighten, as this can strip the threads or damage the grip panels. Tighten until snug.
- Function Check: After installation, perform a function check of your firearm to ensure all controls (e.g., safety, magazine release) operate freely and are not obstructed by the new grips.
Image: Hogue Coco Bolo grip installed on a S&W 1006/4506 series pistol. This image illustrates the appearance of the grip once properly installed on the firearm.
Image: Another view of the Hogue Coco Bolo grip on a S&W 1006/4506 series pistol. This angle provides a different perspective of the grip's fit and finish.
Operation and Usage
The Hogue Coco Bolo grip is a passive component designed to improve the handling and feel of your S&W 1006/4506 Series firearm. Once properly installed, it requires no specific operational steps beyond standard firearm handling. The grip provides a comfortable and secure surface for holding the firearm, enhancing control and reducing fatigue during use.
Always maintain a firm and consistent grip on your firearm, ensuring proper finger placement and trigger discipline. The natural wood material offers a classic aesthetic and a tactile feel that many shooters prefer.
Care and Maintenance
To ensure the longevity and appearance of your Hogue Coco Bolo grip, follow these maintenance guidelines:
- Cleaning: Wipe the grip panels with a soft, dry cloth to remove dirt, oil, and residue after each use. For stubborn grime, a slightly damp cloth with mild soap can be used, but ensure the grip is thoroughly dried immediately afterward. Avoid harsh chemicals or solvents, as these can damage the wood finish.
- Wood Care: Coco Bolo is a natural wood. Periodically, you may wish to apply a small amount of wood-specific oil or wax (e.g., gunstock oil, furniture wax) to nourish the wood and maintain its luster. Apply sparingly and buff off any excess.
- Storage: Store your firearm with the grips in a climate-controlled environment to prevent warping or cracking due to extreme temperature or humidity fluctuations.
- Screw Tightness: Periodically check the tightness of the grip screws. Vibrations from firing can cause screws to loosen over time. Retighten gently if necessary, but do not overtighten.
Troubleshooting
If you encounter any issues with your Hogue Coco Bolo grip, consider the following common solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Grip panels feel loose. | Screws are not tightened sufficiently or have loosened over time. | Gently tighten the grip screws. Do not overtighten. If screws continue to loosen, consider using a small amount of non-permanent threadlocker (e.g., blue Loctite) on the screw threads, applied carefully. |
| Grip panels do not sit flush. | Improper alignment during installation or debris under the grip. | Remove the grip panels, inspect the firearm frame and the back of the grips for any obstructions or debris. Realign and reinstall carefully. Ensure the correct grip model for your firearm. |
| Controls (e.g., safety, magazine release) are obstructed. | Grip panels are misaligned or not fully seated. | Remove and reinstall the grips, paying close attention to alignment around all controls. Ensure the grip is fully seated against the frame. This grip is specifically designed for S&W 1006/4506 series, so fit issues should be minimal if correctly installed. |
If problems persist, or if you suspect a defect, please contact Hogue customer support or a qualified gunsmith.
Product Specifications
| Feature | Detail |
|---|---|
| Product Type | Hunting Grip |
| Brand | Hogue |
| Model Name | 06810 |
| Compatibility | S&W 1006/4506 Series Firearms |
| Material | Coco Bolo Wood |
| Color | Multi (Natural Wood Grain) |
| Item Weight | Approximately 0.26 Pounds (0.12 kg) |
| Country of Origin | United States |
Warranty and Support
Hogue products are known for their quality and craftsmanship. For specific warranty information regarding your Coco Bolo grip, please refer to the official Hogue website or contact their customer service directly. Hogue stands behind its products and is committed to customer satisfaction.
Customer Support: For technical assistance, warranty claims, or product inquiries, please visit the official Hogue website or use the contact information provided on their packaging.
You can find more information and contact details on the Hogue Brand Store on Amazon.
