1. Introduction
Thank you for choosing TAMIYA Spray Lacquer TS-29 SemiGloss Black. This high-quality lacquer spray paint is specifically formulated for model building, providing an excellent semi-gloss finish on various surfaces. It is ideal for preparing ABS and Styrene plastic for paint, and can also be used on metal parts. This manual provides essential information for safe and effective use of the product.
A black spray paint can with a white label featuring the TAMIYA COLOR logo, red and blue stars, and text indicating 'FOR PLASTICS' and 'SemiGloss Black'.
2. Safety Information
WARNING: EXTREMELY FLAMMABLE LIQUID AND VAPORS.
Read all warnings and instructions carefully before use. Keep away from heat, open flames, sparks, and other ignition sources. Use only in a well-ventilated area. Avoid breathing mist and vapors. Use proper personal protective equipment including appropriate gloves and safety glasses/goggles. Wash thoroughly after handling.
Potential Adverse Health Effects:
- Ingestion may cause harmful effects. Do not ingest.
- Prolonged and/or repeated exposure may cause kidney and liver damage.
- Prolonged or repeated contact with skin may cause irritation, dryness of skin, and defatting and dermatitis. Avoid prolonged skin contact.
- Inhalation of mist vapors may cause irritation, silicosis, and central nervous system effects characterized by nausea, headache, dizziness, unconsciousness, and under conditions of overexposure even death.
KEEP OUT OF REACH OF CHILDREN. Only for Adult Modelers, Age 14 years and above.
WARNING: CONTENTS UNDER PRESSURE. Do not puncture or incinerate container. Do not expose to heat or store at a temperature above 120°F (49°C).
First Aid:
- Eye and Skin Contact: Flush with water for 15 minutes. Get prompt medical attention.
- Ingestion: If swallowed, do not induce vomiting. Get prompt medical attention.
- Inhalation: If person is overpowered by fumes or vapors, remove affected person to fresh air and get medical attention.
For more health information, call a Poison Control Center at 1-800-222-1222.
3. Preparation
- Surface Preparation: Ensure the surface to be painted is clean, dry, and free of dust, grease, and other contaminants. For best results, lightly sand smooth surfaces to provide adhesion.
- Environmental Conditions: Use only in a well-ventilated area. Recommended temperature for application is between 50°F (10°C) and 86°F (30°C). Avoid high humidity.
- Protect Surroundings: Cover adjacent areas to protect them from overspray.
4. Application (Operating)
- Shake Can: Shake the can vigorously for at least one minute after the mixing ball begins to rattle, and occasionally during use to ensure even color and consistency.
- Test Spray: Before applying to your model, test spray on a scrap piece of material to check color and spray pattern.
- Application Distance: Hold the can approximately 10 to 12 inches (25-30 cm) from the object.
- Spray Technique: Apply paint in light, even mist coats using steady, sweeping strokes. Do not stop in the middle of a stroke. Overlap each stroke slightly.
- Multiple Coats: For desired depth of color and coverage, apply several thin coats rather than one thick coat. Allow sufficient drying time between coats (typically 10-15 minutes, depending on conditions).
- Drying Time: The paint is typically touch-dry within 15-30 minutes and fully cured in 24 hours.
5. Cleanup & Storage (Maintenance)
- Clear Nozzle: After each use, invert the can and spray for a few seconds until only clear propellant comes out. This prevents the nozzle from clogging.
- Storage: Store the can in a cool, dry place, away from direct sunlight, heat sources, and open flames. Ensure the cap is securely placed on the can.
- Disposal: Dispose of empty cans according to local regulations. Do not puncture or incinerate.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Uneven spray / Splattering | Insufficient shaking; nozzle clogged; too close to surface. | Shake vigorously; clear nozzle (invert can and spray); maintain proper distance. |
| Paint runs / Drips | Too much paint applied in one coat; too close to surface. | Apply thinner, even coats; maintain proper distance. |
| Poor adhesion | Surface not clean or properly prepared. | Clean and prepare surface thoroughly (e.g., light sanding). |
| Nozzle clogged | Paint dried in nozzle. | Invert can and spray until clear propellant comes out after each use. If already clogged, try soaking nozzle in paint thinner. |
7. Specifications
- Brand: TAMIYA
- Model Name: TAM85029
- Color: SemiGloss Black
- Finish Type: Semi-Gloss
- Item Volume: 100 Milliliters (3.3 Fl Oz)
- Paint Type: Spray Lacquer
- Specific Uses: Model building (Car, Plastic, Metal)
- Surface Recommendation: Plastic, Metal (specifically ABS and Styrene plastic)
- Special Feature: Flammable
- Included Components: Paint
- Product Dimensions: Approximately 2.05 x 2.05 x 4.21 inches
- Item Weight: Approximately 0.01 ounces (can weight not specified, this is product weight)
- Recommended Age: 14 years and up
8. Warranty & Support
For specific warranty information or technical support regarding your TAMIYA Spray Lacquer, please refer to the official TAMIYA website or contact their customer service directly. Keep your purchase receipt as proof of purchase.
Tamiya America, Inc.
Address: 2677 White Road, Irvine, CA 92614, USA
Website: www.tamiyausa.com