Introduction
This manual provides detailed instructions for the safe installation, operation, and maintenance of your John Timberland Casa Seville Rustic Post Light Fixture. Please read all instructions carefully before beginning installation and retain this manual for future reference.
Important Safety Information
- Always turn off the power at the main fuse or circuit breaker box before beginning installation or performing any maintenance.
- Consult a qualified electrician if you are unsure about any part of the installation process.
- Wear safety glasses and appropriate protective gear during installation.
- This fixture is UL listed and rated for wet locations, suitable for outdoor use.
- Proposition 65 Warning: This product may contain chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Wash hands after handling.
Package Contents
Verify that all components are present before discarding packaging materials.
- 1 x Casa Seville Rustic Post Light Fixture
Note: The mounting post and pier mount adapter are not included and must be purchased separately. This fixture is designed to fit a standard 3-inch diameter pole.
Tools and Materials Required (Not Included)
- Phillips head screwdriver
- Wire strippers
- Electrical tape
- Pliers
- Ladder (if necessary for height)
- Safety glasses
- UL-listed wire connectors
- Three (3) Candelabra base (E12) light bulbs, maximum 40 watts each
Setup and Installation
Follow these steps to properly install your post light fixture. Ensure power is OFF at the circuit breaker before proceeding.
- Prepare the Post: Ensure your existing outdoor post is securely installed and has a standard 3-inch diameter. The electrical wiring should extend from the top of the post.
- Mount the Fixture: Carefully place the base of the post light fixture over the top of the 3-inch diameter post. The fixture should slide down securely.
- Wiring Connections:
- Connect the black wire from the fixture to the black (hot) wire from your electrical supply using a UL-listed wire connector.
- Connect the white wire from the fixture to the white (neutral) wire from your electrical supply using a UL-listed wire connector.
- Connect the ground wire (bare copper or green) from the fixture to the ground wire from your electrical supply. If no ground wire is present in the supply, consult a qualified electrician.
- Secure all wire connections with electrical tape.
- Secure the Fixture: Once wiring is complete and connections are secure, gently push the wires into the post. Secure the fixture to the post using any provided screws or mounting hardware.
- Install Light Bulbs: Insert three (3) candelabra base (E12) light bulbs, each with a maximum wattage of 40 watts, into the sockets. Do not exceed the maximum wattage.
- Restore Power: Turn the power back on at the main fuse or circuit breaker box. Test the light fixture.
Image: The John Timberland Casa Seville Rustic Post Light Fixture, showcasing its dark walnut finish, iron scrollwork, and hammered glass panels. This image provides an overall view of the product.
Image: The Casa Seville Post Light fixture installed on a stone pier, demonstrating its appearance in an outdoor setting. Note that a pier mount adapter is required for this type of installation and is sold separately.
Operating Instructions
The John Timberland Casa Seville Rustic Post Light Fixture operates via a standard wall switch connected to its electrical supply. Once installed and wired correctly, simply use the wall switch to turn the light on or off.
For optimal performance and longevity, ensure the fixture is not exposed to excessive moisture or physical impact.
Maintenance
Cleaning
- Ensure power is OFF at the circuit breaker before cleaning.
- Wipe the fixture with a soft, damp cloth. Do not use abrasive cleaners, solvents, or polishes as they may damage the finish or glass.
- For glass panels, a mild glass cleaner can be used, applied to a cloth first, not directly to the fixture.
Bulb Replacement
- Ensure power is OFF at the circuit breaker and the fixture has cooled completely before attempting to replace bulbs.
- Carefully unscrew the old bulbs.
- Screw in new candelabra base (E12) bulbs, ensuring they do not exceed 40 watts each.
- Restore power and test the light.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power to the fixture. | Check circuit breaker or fuse. Ensure wall switch is on. |
| Loose or incorrect wiring. | Turn off power. Check all wire connections for tightness and correct polarity. | |
| Faulty light bulb. | Replace bulb(s) with new ones of the correct type and wattage. | |
| Light flickers. | Loose bulb or wiring connection. | Turn off power. Tighten bulbs. Check wire connections. |
| Incorrect bulb type or wattage. | Ensure bulbs are E12 base, 40 watts maximum. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | 63825 |
| Dimensions (H x W) | 23.5 inches x 12 inches |
| Weight | 16.28 lbs |
| Material | Alloy Steel (frame), Glass (shade) |
| Finish | Dark Walnut (over steel), Bronze finish type |
| Bulb Base | E12 (Candelabra) |
| Number of Bulbs | 3 (not included) |
| Max Wattage per Bulb | 40 Watts |
| Voltage | 120 Volts |
| Installation Type | Pole Mount (fits standard 3-inch diameter pole) |
| Indoor/Outdoor Use | Outdoor (Wet Location Rated) |
| Certifications | UL Listed |
Image: A diagram illustrating the dimensions of the Casa Seville Post Light, showing a width of 12 inches and a height of 23.5 inches.
Warranty and Support
For warranty information or technical support regarding your John Timberland Casa Seville Rustic Post Light Fixture, please refer to the original purchase documentation or contact John Timberland customer service directly. Contact details can typically be found on the manufacturer's official website or on your product packaging.
