1. Product Overview
The TOA CS-64 Paging Speaker is an outdoor speaker designed for high intelligibility and sound quality in various environments. It features durable stainless steel hardware for all-weather performance and incorporates a rotary switch for easy impedance changes, making it adaptable to different audio systems.
An image showing the TOA CS-64 Paging Speaker, a white horn-shaped speaker with a black grille and a sturdy mounting bracket.
2. Safety Instructions
Please read and understand all safety instructions before installing or operating the speaker. Failure to do so may result in injury or damage to the equipment.
- Electrical Safety: Ensure all wiring is performed by a qualified professional and complies with local electrical codes. Disconnect power before making any connections.
- Mounting: Use appropriate mounting hardware for the installation surface. Ensure the mounting location can support the weight of the speaker.
- Outdoor Use: While designed for outdoor use, protect connections from direct water exposure to prevent short circuits.
- Handling: Do not drop or subject the speaker to severe impact.
- Ventilation: Ensure adequate ventilation around the speaker if installed in an enclosed space, though typically not required for this outdoor speaker type.
3. Package Contents
Verify that all items are present in the package:
- TOA CS-64 Paging Speaker
- Mounting Bracket (pre-attached or separate)
- Instruction Manual (this document)
- Necessary mounting hardware (screws, washers, nuts)
4. Setup and Installation
Follow these steps for proper installation of your TOA CS-64 Paging Speaker:
- Choose Mounting Location: Select a suitable wall or pole location that provides optimal sound coverage and is structurally sound to support the speaker's weight.
- Mounting the Speaker:
- Position the mounting bracket against the desired surface and mark the drilling points.
- Drill pilot holes appropriate for your mounting hardware.
- Securely attach the speaker's mounting bracket to the surface using the provided or suitable hardware. Ensure it is firmly fixed.
- Adjust the speaker's angle for optimal sound direction.
- Wiring Connections:
- Locate the input terminals on the speaker.
- Connect the speaker wires from your amplifier or paging system to the speaker terminals. Pay attention to polarity (+ and -).
- Impedance Selection: The CS-64 features a rotary switch for impedance selection. Before connecting to your amplifier, set the rotary switch to the impedance (e.g., 8 ohms, 70V, 100V) that matches your amplifier's output and system requirements. Refer to your amplifier's manual for compatible impedance settings.
- Ensure all connections are secure and insulated to prevent short circuits.
5. Operating Instructions
Once the speaker is properly installed and wired, operation is straightforward:
- Power On: Turn on your amplifier or paging system.
- Volume Adjustment: Adjust the volume level on your amplifier to the desired output. Start with a low volume and gradually increase it to prevent sudden loud sounds.
- Testing: Play an audio signal (e.g., music, voice announcement) through the system to confirm proper operation and sound quality.
6. Maintenance
The TOA CS-64 speaker is designed for durability, but regular maintenance can extend its lifespan and ensure optimal performance:
- Cleaning: Periodically wipe the exterior of the speaker with a soft, damp cloth to remove dust and dirt. Do not use harsh chemicals or abrasive cleaners.
- Inspection: Annually inspect the mounting hardware and wiring connections for any signs of corrosion, loosening, or damage. Tighten any loose screws and replace damaged components immediately.
- Drainage: Ensure that any drainage holes on the speaker (if present) are clear of debris to prevent water accumulation.
7. Troubleshooting
If you encounter issues with your TOA CS-64 speaker, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| No Sound | No power to amplifier; incorrect wiring; impedance mismatch; faulty amplifier. | Check amplifier power; verify speaker wire connections and polarity; ensure impedance setting matches amplifier; test with another amplifier if possible. |
| Distorted Sound | Overdriven amplifier; incorrect impedance setting; damaged speaker cone; loose connections. | Reduce amplifier volume; verify impedance setting; inspect speaker for physical damage; check all wiring connections. |
| Intermittent Sound | Loose wiring connections; faulty cable. | Secure all speaker wire connections; replace speaker cable if damaged. |
If the problem persists after trying these solutions, please contact TOA customer support or a qualified audio technician.
8. Specifications
| Feature | Specification |
|---|---|
| Manufacturer | TOA Electronics |
| Model Name | CS 64 |
| Speaker Type | Outdoor |
| Speaker Maximum Output Power | 100 Watts |
| Mounting Type | Wall Mount |
| Item Weight | 8 pounds |
| ASIN | B0012ESUQ4 |
| Date First Available | August 28, 2018 |
| Is Waterproof | FALSE |
9. Warranty and Support
For information regarding the product warranty, please refer to the warranty card included with your purchase or visit the official TOA Electronics website. For technical support or service inquiries, please contact TOA customer service through their official channels.
