Product Overview
The Rust-Oleum High Heat Enamel Spray Paint is specifically formulated to renew and protect metal surfaces exposed to high temperatures. This product is ideal for use on items such as barbecue grills, wood-burning stoves, radiators, and engines. It provides rust protection and retains color and finish even after repeated heating, withstanding surface temperatures up to 1200°F (648°C).
Figure 1: Rust-Oleum High Heat Enamel Spray Paint, Bar-B-Que Black.
Safety Information
Always read and follow all instructions and warnings on the product label before use. Ensure adequate ventilation during application. Wear appropriate personal protective equipment, including gloves and eye protection.
Figure 2: Recommended safety and preparation items for paint application.
WARNING: This product is not for use in areas directly exposed to flames, such as inside of fireplaces, grills, boilers, ovens, and stovetops.
Figure 3: Important safety warning regarding direct flame exposure.
Setup and Surface Preparation
Proper surface preparation is crucial for optimal adhesion and durability. Ensure the area is well-ventilated.
- Clean the Surface: Remove all dirt, grease, oil, salt, and chemical contaminants by washing the surface with a commercial cleaner or other suitable cleaning method. Rinse thoroughly with fresh water and allow to dry completely.
- Remove Loose Rust and Paint: Scrape off any loose rust and peeling paint with a wire brush or sandpaper. Lightly sand glossy surfaces to create a profile for better adhesion.
- Mask Adjacent Areas: Use painter's tape and drop cloths to protect surrounding areas from overspray.
- Do Not Prime: A primer is not necessary for this high heat enamel.
Figure 4: Visual guide for surface preparation and application.
Operating Instructions (Application)
Follow these steps for effective application of the High Heat Enamel Spray Paint:
- Shake Well: Shake the can vigorously for one minute after the mixing ball begins to rattle. Continue to shake occasionally during use.
- Apply in Light Layers: Hold the can 10-16 inches from the surface and spray in a steady, back-and-forth motion, slightly overlapping each stroke. Apply several thin coats a few minutes apart rather than one heavy coat to avoid drips and ensure even coverage.
- Drying Time: Allow the painted surface to dry for at least 2 hours in a well-ventilated area before proceeding to the heat cure.
- Heat Cure: After drying, remove any painter's tape. Heat cure the painted item at 450°F (232°C) for 1 hour. This process helps the paint achieve its full durability and heat resistance. The finish may transition from a satin to a flat appearance after heat curing.
Figure 5: The paint's finish may change after heat curing.
Figure 6: Example of a surface before and after application.
Maintenance
Once applied and heat-cured, the Rust-Oleum High Heat Enamel provides a durable finish that resists outdoor weathering, rust, corrosion, and chipping. To maintain the appearance and protective qualities of the painted surface:
- Regularly clean the surface with mild soap and water. Avoid abrasive cleaners or scrubbing pads that could damage the finish.
- Inspect the painted surface periodically for any signs of wear or damage. Touch up small areas as needed following the application instructions.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Poor Adhesion / Flaking | Improper surface preparation (e.g., surface not clean, loose rust/paint not removed). Insufficient heat curing. | Ensure surface is thoroughly cleaned and free of contaminants. Remove all loose material. Ensure heat cure is performed at the specified temperature and duration. |
| Uneven Finish / Drips | Applying too much paint in one coat. Holding can too close to surface. | Apply multiple thin coats instead of one heavy coat. Maintain recommended distance (10-16 inches) from the surface during spraying. |
| Color Change After Heat Cure | This is a normal characteristic of the product. | No action required. The paint is designed to transition from a satin to a flat finish after heat curing. |
Specifications
| Brand | Rust-Oleum |
| Model Number | 7778830 |
| Color | Bar-B-Que Black |
| Finish Type | Satin (becomes Flat after heat cure) |
| Size | 12 Ounce (Pack of 1) |
| Item Volume | 12 Fluid Ounces |
| Special Feature | Rust Resistant |
| Paint Type | Spray |
| Specific Uses For Product | Interior/Exterior (on metal items subject to heat) |
| Surface Recommendation | Metal |
| Indoor/Outdoor Usage | Outdoor |
| Max Temperature Resistance | Up to 1200°F (648°C) |
| Coverage | Up to 7-8 sq. ft. |
| Dry to Touch | 30 minutes |
| UPC | 020066777883 |
Figure 7: Temperature resistance of the enamel.
Warranty and Support
Rust-Oleum products are backed by a limited warranty. For specific warranty details or technical support, please visit the official Rust-Oleum website or contact their customer service department. The official user guide is also available for download:
For further assistance, you may visit the Rust-Oleum Store on Amazon.
