Westek TM08DHB Decorative Indoor Power Strip Timer

Introduction

The Westek TM08DHB Decorative Indoor Power Strip Timer is designed to provide automated power control for various indoor electrical devices. This unit combines the functionality of a power strip with a mechanical timer, allowing users to program specific on/off cycles for connected appliances, lights, or other electronics. It enhances convenience and can contribute to energy management by ensuring devices are powered only when needed.

Safety Information

• Indoor Use Only: This power strip timer is intended for indoor use in dry locations. Do not expose to moisture or wet conditions.
• Electrical Rating: Do not exceed the electrical ratings of the unit. Overloading the power strip can cause overheating and fire hazards.
• Grounding: Always plug the power strip into a grounded 3-prong wall outlet.
• Children and Pets: Keep out of reach of children and pets.
• Disconnection: To disconnect power, remove the power strip from the wall outlet.
• Inspection: Regularly inspect the power strip and connected cords for damage. Do not use if damaged.

Package Contents

• One Westek TM08DHB Decorative Indoor Power Strip Timer

Product Overview

The Westek TM08DHB features a compact design with multiple outlets and an integrated mechanical timer. It is equipped with a manual override switch for flexible control.

Image: The Westek TM08DHB power strip timer. This image displays the white power strip with its attached power cord, the circular timer dial, a red manual switch, and the eight 3-prong outlets.

• Eight 3-Prong Outlets: The power strip provides eight outlets for connecting devices.
• Timer-Controlled Outlets: Four of the eight outlets are controlled by the integrated timer.
• Always-On Outlets: The remaining four outlets provide continuous power, independent of the timer settings.
• Mechanical Timer Dial: A circular dial with 30-minute interval pins allows for daily programming.
• Manual Override Switch: A switch (typically labeled ON/TIMER/OFF) allows you to bypass the timer for continuous power or to turn off all controlled outlets.

Setup

1. Unpack: Carefully remove the power strip timer from its packaging.
2. Identify Outlets: Observe the power strip to identify which outlets are timer-controlled and which are always-on. This is usually indicated by markings on the unit.
3. Placement: Position the power strip in a dry, indoor location where it can be easily accessed and is away from flammable materials.
4. Plug In: Insert the power strip's plug into a standard, grounded 3-prong wall outlet.
5. Connect Devices: Plug your desired devices into the appropriate outlets. For automated control, use the timer-controlled outlets. For continuous power, use the always-on outlets.

Operating Instructions

The TM08DHB timer operates on a 24-hour cycle, allowing for multiple on/off settings per day.

1. Set Current Time: Rotate the entire timer dial clockwise until the current time aligns with the arrow or indicator mark on the timer's face. The dial is marked with hours (e.g., 1-24 or 1-12 AM/PM).
2. Program On/Off Times:
   • The timer dial is surrounded by small, non-removable pins. Each pin represents a 30-minute interval.
   • To set a period for the timer-controlled outlets to be ON, push the corresponding pins downwards.
   • To set a period for the timer-controlled outlets to be OFF, leave the corresponding pins in the upward position.
   • You can program up to 24 on/off settings per day by pushing down or pulling up the pins for the desired 30-minute intervals.
3. Select Operating Mode: Locate the manual override switch (often a red switch) on the power strip. This switch typically has three positions:
   • ON: The timer-controlled outlets will remain continuously on, bypassing the timer settings.
   • TIMER: The timer-controlled outlets will operate according to your programmed on/off settings.
   • OFF: The timer-controlled outlets will remain continuously off, bypassing the timer settings.

   Set the switch to the TIMER position for automated operation.

Maintenance

• Cleaning: Disconnect the power strip from the wall outlet before cleaning. Wipe the unit with a dry, soft cloth. Do not use liquid cleaners or immerse the unit in water.
• Storage: When not in use, store the power strip in a cool, dry place, away from direct sunlight and extreme temperatures.

Troubleshooting

• Timer-controlled outlets are not turning on/off:
  • Ensure the manual override switch is set to the TIMER position.
  • Verify that the current time is correctly set on the dial.
  • Check that the pins corresponding to the desired ON/OFF times are correctly pushed down (ON) or left up (OFF).
  • Confirm the power strip is securely plugged into a live wall outlet.
• All outlets are not working:
  • Check the wall outlet by plugging in another device to ensure it has power.
  • Inspect the power strip's cord and plug for any damage.
• Timer is making noise:
  • A slight humming sound from mechanical timers is normal. If the noise is excessive or unusual, discontinue use and contact customer support.
• Timing is inconsistent (e.g., turns on/off a few minutes early/late):
  • Mechanical timers may have slight variations in timing accuracy. For applications requiring precise timing, a digital timer may be more suitable.

Specifications

Warranty and Support

For warranty information or technical support, please refer to the manufacturer's official website or contact their customer service department. Keep your purchase receipt for warranty claims.