FJC 2491

FJC 2491 PAG Oil - 32 fl. oz. Instruction Manual

Model: 2491

1. Product Overview

The FJC 2491 PAG Oil is a high-quality synthetic Polyalkylene Glycol (PAG) lubricant specifically formulated for use in automotive air conditioning systems. This product is designed to meet OE (Original Equipment) viscosity standards and is recommended by both OE and compressor manufacturers for optimal performance and system longevity.

It is a PAG 150 viscosity oil, suitable for R134a refrigerant systems. The oil contains synthetic refrigerant oil (Polyalkylene Glycol) along with essential additives to ensure proper lubrication and corrosion prevention within the A/C system.

FJC 2491 PAG Oil 32 fl. oz. bottle

Figure 1: FJC 2491 PAG Oil, 32 fl. oz. bottle. A black plastic bottle with a red and silver label indicating "PAG 150", "Viscosity 150", "R134a Synthetic Refrigerant Oil", and "1 Quart".

2. Important Safety Information

3. Setup and Preparation

Before adding FJC 2491 PAG Oil to an automotive A/C system, ensure the system is properly prepared. This typically involves evacuating the system to remove all existing refrigerant and moisture. Consult your vehicle's service manual or a qualified automotive technician for specific procedures related to your vehicle's A/C system.

3.1 Tools and Materials Required:

3.2 System Evacuation:

It is crucial to evacuate the A/C system thoroughly before adding new oil or refrigerant. This process removes air and moisture, which can cause system damage and reduce cooling efficiency. Follow standard automotive A/C service procedures for evacuation.

4. Operating Instructions (Adding Oil)

The FJC 2491 PAG Oil is designed to be added to the A/C compressor or directly into the A/C system during service or repair. The exact amount of oil required will vary depending on the vehicle manufacturer's specifications and the extent of the A/C system repair (e.g., compressor replacement, component replacement).

4.1 Adding Oil to a New Compressor:

  1. Drain any shipping oil from the new compressor.
  2. Measure the correct amount of FJC 2491 PAG Oil as specified by the vehicle manufacturer or compressor manufacturer.
  3. Pour the measured oil into the new compressor's suction port or designated oil fill port.
  4. Install the compressor and proceed with system evacuation and recharging.

4.2 Adding Oil to an Existing System:

  1. Determine the amount of oil to be added based on the component replaced (e.g., accumulator/drier, condenser, evaporator). Refer to vehicle service data for oil capacity charts.
  2. Use an appropriate oil injector tool to introduce the FJC 2491 PAG Oil into the low-pressure side of the A/C system after evacuation and before refrigerant charging.
  3. Ensure the system is under vacuum before injecting oil to draw the oil into the system.
  4. Once the oil is added, proceed with refrigerant charging according to manufacturer specifications.

Note: Always refer to the vehicle manufacturer's service manual for precise oil capacities and procedures. Using the incorrect type or amount of oil can lead to A/C system damage.

5. Maintenance

PAG oil does not typically require routine replacement unless an A/C system component is replaced or a leak occurs. However, regular maintenance of your vehicle's A/C system is crucial for its longevity and efficiency.

5.1 Recommended Practices:

6. Troubleshooting

Issues related to A/C oil are often symptoms of broader system problems. If you experience A/C performance issues, consider the following:

SymptomPossible CauseAction
Poor A/C CoolingIncorrect oil level (too low or too high), incorrect oil type, moisture in system.Verify correct oil type and level. Evacuate and recharge system. Consult a professional.
Compressor NoiseInsufficient lubrication due to low oil, incorrect oil viscosity.Check oil level and type. If noise persists, compressor may be damaged.
System LeaksDamaged seals or components, overfilling with oil.Identify and repair leaks. Ensure proper oil charge.

For complex A/C system issues, it is highly recommended to seek assistance from a certified automotive A/C technician.

7. Product Specifications

AttributeDetail
BrandFJC
Model Number2491
MaterialSynthetic
Liquid Volume32 Fluid Ounces (1 Quart)
ViscosityPAG 150 (1.5E+2 cs)
Recommended UseAutomotive A/C Systems (R134a)
Specific UsePrevent Corrosion
Item FormOil
Package InformationBottle
Item Weight2.1 Pounds
Product Dimensions5.15 x 2.13 x 7.79 inches
UPC609989005626

8. Warranty and Support

For specific warranty information regarding the FJC 2491 PAG Oil, please refer to the documentation provided with your purchase or contact FJC directly. Warranty terms typically cover manufacturing defects.

8.1 Customer Support:

If you have questions about the FJC 2491 PAG Oil or require technical assistance, please visit the official FJC website or contact their customer service department. Contact information can usually be found on the product packaging or the manufacturer's website.

Note: No official product videos were found for this item.

Related Documents - 2491

Preview FJC 53040 DC to AC 400 Watt Power Inverter User Manual
User manual for the FJC 53040 DC to AC 400 Watt Power Inverter. Provides instructions on operation, safety precautions, troubleshooting, and specifications for converting 12V DC vehicle power to 110V AC power.
Preview Spex Manta Classic Back Support: Selection and Configuration Guide
Detailed guide for selecting, configuring, and ordering the Spex Manta Classic Back Support. Includes size charts, color options, hardware choices, and accessories for customized wheelchair seating solutions.
Preview Oster Hand Mixer with Retractable Cord User Manual & Guide
Comprehensive user manual and guide for the Oster Hand Mixer with Retractable Cord (Models 2491, 2492, 2494, 2496), covering features, operation, safety, cleaning, and warranty information.
Preview Autec Dynamic Series Radio Remote Control Instruction Manual
Instruction manual for the use and maintenance of Autec Dynamic Series Radio Remote Controls, including FJN Transmitting Unit, CRX Receiving Unit, LPM02 battery, and ULC932A battery charger. Covers safety, operation, installation, and troubleshooting for industrial wireless control systems.
Preview Lexmark Forms Printer 248x/249x Technical Reference Guide
Comprehensive technical reference for Lexmark Forms Printer 248x/249x series, detailing printer commands, interface options, character downloading, and barcode generation for developers and technicians.