RAB Lighting LFP16A Sleek Floodlight Instruction Manual

1. Product Overview

The RAB Lighting LFP16A Sleek Floodlight is designed for outdoor illumination, providing efficient and durable lighting. This fixture accommodates a PAR16 type bulb and features a robust die-cast aluminum housing with a powder-coated finish for enhanced durability and weather resistance.

Key Features:

• Designed for 60W PAR16 bulbs, delivering 650 lumens output (bulb not included).
• Durable die-cast aluminum housing with a powder-coated finish.
• Gasket and O-ring seals provide resistance against weather elements.
• Integrated shield helps reduce glare.
• Equipped with a 1/2" NPS threaded arm for secure mounting and a locking swivel for adjustable positioning.

Figure 1: RAB Lighting LFP16A Sleek Floodlight. This image shows the floodlight fixture with its threaded arm and wiring, highlighting its compact and durable design.

2. Safety Information

Please read and understand all instructions before installing or operating this product. Failure to follow these instructions may result in electric shock, fire, or other hazards that could cause property damage or personal injury.

• Electrical Safety: Always disconnect power at the circuit breaker or fuse box before wiring or servicing the fixture.
• Qualified Electrician: Installation should be performed by a qualified electrician in accordance with all local and national electrical codes.
• Grounding: Ensure the fixture is properly grounded to avoid potential electrical hazards.
• Bulb Type: Use only PAR16 type bulbs with a maximum wattage of 60W. Exceeding the maximum wattage can cause overheating and damage to the fixture.
• Wet Location: This fixture is suitable for wet locations. Ensure all connections are properly sealed and waterproofed during installation.
• Temperature: Do not install near combustible materials or surfaces that may be affected by heat.

3. Package Contents

Verify that all components are present before beginning installation:

• RAB Lighting LFP16A Sleek Floodlight Fixture (1)
• Instruction Manual (1)

Note: Light bulb and wire connectors are not included and must be purchased separately.

4. Setup and Installation

This floodlight is designed for wall mounting and features a 1/2" NPS threaded arm for secure attachment to a junction box or mounting accessory. Follow these steps for proper installation:

1. Prepare for Installation:
   • Turn off power at the circuit breaker before starting any electrical work.
   • Gather necessary tools: screwdriver, wire strippers, electrical tape, silicone sealant (for waterproofing).
2. Mount the Fixture:
   • Thread the 1/2" NPS arm of the floodlight into a compatible outdoor junction box or mounting plate. Ensure a tight and secure connection.
   • Use the locking swivel to adjust the initial angle of the fixture.
   

   Figure 2: Detail of the 1/2" NPS threaded arm and 180-degree adjustable swivel. This illustrates the mounting mechanism and flexibility of the floodlight.
3. Wiring Connections:
   • Connect the black wire from the fixture to the hot (black) wire from the power supply.
   • Connect the white wire from the fixture to the neutral (white) wire from the power supply.
   • Connect the bare copper or green wire from the fixture to the ground wire from the power supply.
   • Secure all connections with appropriate wire connectors and electrical tape. For outdoor installations, consider using silicone-filled wire nuts for added moisture protection.
4. Install Bulb:
   • Carefully insert a PAR16 bulb (max 60W) into the fixture socket. Do not overtighten.
5. Seal and Test:
   • Ensure all connections are secure and the fixture is properly sealed against moisture. Apply silicone sealant around the mounting base if necessary.
   • Restore power at the circuit breaker and test the floodlight's operation.

5. Operating Instructions

Once installed and powered, the RAB Lighting LFP16A Floodlight operates by the control of the circuit it is connected to (e.g., a wall switch, timer, or photocell). There are no direct controls on the fixture itself.

• Adjusting Light Direction: The fixture features a locking swivel arm. To adjust the light direction, loosen the locking nut on the swivel, position the floodlight as desired, and then tighten the locking nut securely.
• Glare Reduction: The built-in shield is designed to minimize glare, directing light effectively to the intended area.

Figure 3: Example of the LFP16A floodlight used in a landscape setting, demonstrating its illumination capabilities.

6. Maintenance

Regular maintenance ensures optimal performance and longevity of your floodlight.

• Cleaning: Periodically clean the exterior of the fixture with a soft, damp cloth. Do not use abrasive cleaners or solvents, as these can damage the finish. Ensure power is off before cleaning.
• Bulb Replacement:
  1. Turn off power to the fixture at the circuit breaker.
  2. Allow the old bulb to cool completely before handling.
  3. Carefully unscrew and remove the old PAR16 bulb.
  4. Insert a new PAR16 bulb (max 60W) into the socket, ensuring it is seated correctly.
  5. Restore power and test the new bulb.
• Inspection: Annually inspect the fixture for any signs of wear, damage, or loose connections. Address any issues promptly.

7. Troubleshooting

8. Specifications

9. Warranty and Support

The RAB Lighting LFP16A Sleek Floodlight comes with a 1-year manufacturer's warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use.

For warranty claims, technical support, or further assistance, please contact RAB Lighting customer service. Refer to the official RAB Lighting website for the most current contact information.

Manufacturer: RAB Lighting

Website: www.rablighting.com (Example link, actual link may vary)