Ushio BC2393 EYV JCV130V-500WGSF Frosted Projector Halogen Light Bulb Instruction Manual

1. Introduction

This manual provides essential information for the safe and effective use of your Ushio BC2393 EYV JCV130V-500WGSF Frosted Projector Halogen Light Bulb. Please read these instructions carefully before installation and operation. This halogen bulb is designed for specific applications such as interior, recessed, track, and security lighting, offering a whiter, brighter light and longer life compared to traditional incandescent bulbs.

2. Safety Information

Always observe the following safety precautions to prevent injury or damage:

• Power Off: Always ensure the power supply to the fixture is turned off before installing, removing, or handling the bulb.
• Cool Down: Allow the bulb to cool completely before handling. Halogen bulbs operate at high temperatures and can cause severe burns.
• Proper Handling: Avoid touching the glass part of the bulb directly with bare hands. Oils from your skin can create hot spots, leading to premature failure. Use a clean cloth or gloves.
• Correct Voltage and Wattage: Ensure the bulb's voltage (130V) and wattage (500W) match the requirements of your fixture. Using an incorrect bulb can cause damage or fire.
• Fixture Compatibility: Use only in fixtures designed for halogen bulbs and rated for the bulb's wattage.
• Ventilation: Ensure adequate ventilation around the bulb to dissipate heat.
• Disposal: Dispose of used or broken bulbs according to local regulations.

3. Product Overview

The Ushio BC2393 EYV JCV130V-500WGSF is a frosted halogen light bulb featuring an E11 mini candelabra base. It is designed to provide 500 watts of illumination at 130 volts, making it suitable for various projector and specialized lighting applications. The frosted finish helps to diffuse light evenly.

Image: A frosted halogen light bulb with an E11 mini candelabra base, designed for projector applications.

4. Setup and Installation

1. Verify Compatibility: Confirm that your lighting fixture is compatible with an E11 mini candelabra base, 130V, and 500W halogen bulbs.
2. Turn Off Power: Locate the circuit breaker or switch controlling the fixture and turn off the power completely.
3. Allow Cooling: If replacing an existing bulb, ensure it has cooled down sufficiently before touching.
4. Remove Old Bulb (if applicable): Carefully unscrew the old bulb from the socket.
5. Install New Bulb: Holding the Ushio BC2393 bulb with a clean cloth or gloves, gently screw it into the E11 socket until it is snug. Do not overtighten.
6. Restore Power: Once the bulb is securely installed, restore power to the fixture.

5. Operating Instructions

After successful installation, operate the Ushio BC2393 halogen bulb by simply turning on the power switch connected to the fixture. This bulb is dimmable with most compatible dimmers, allowing for adjustable light output. Ensure any dimmer used is rated for halogen bulbs and the total wattage.

6. Maintenance

Minimal maintenance is required for this halogen bulb. To ensure optimal performance and longevity:

• Cleaning: If the bulb accumulates dust or debris, ensure the power is off and the bulb is cool. Gently wipe the exterior with a soft, dry, lint-free cloth. Avoid using liquid cleaners.
• Replacement: Replace the bulb when it reaches the end of its rated life or if it fails prematurely. Follow the installation steps for safe replacement.

7. Troubleshooting

If the bulb does not light up after installation, consider the following:

• No Power: Check if the power switch is on and if the circuit breaker has tripped.
• Improper Installation: Ensure the bulb is screwed in correctly and making proper contact with the socket.
• Defective Bulb: Although rare, a new bulb can sometimes be defective. If possible, test with another known working bulb.
• Fixture Issue: If other bulbs also fail in the same fixture, the issue might be with the fixture wiring or socket. Consult a qualified electrician.

8. Specifications

9. Warranty and Support

Warranty: The manufacturer's warranty for this product is not applicable. Please refer to your retailer's return policy for any issues.

Support: For further assistance or inquiries regarding the Ushio BC2393 EYV JCV130V-500WGSF Frosted Projector Halogen Light Bulb, please contact the retailer from whom you purchased the product.