Introduction
This instruction manual provides detailed guidance for the safe installation, operation, and maintenance of your Leviton 5645-W Decora 3-Way/AC Combination Switch. Please read this manual thoroughly before beginning installation and retain it for future reference. This device combines a 15 Amp, 120 Volt 3-Way switch with an AC receptacle in a single unit, designed for commercial and residential applications.
Important Safety Information
WARNING: TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE WIRING!
- This product must be installed in accordance with all national and local electrical codes.
- If you are unsure about any part of these instructions, consult a qualified electrician.
- Do not use this device with aluminum wiring. Use copper wiring only.
- Ensure all wire connections are secure. Loose connections can cause overheating and fire.
- This device is designed for indoor use only.
- Do not exceed the maximum electrical ratings of 15 Amps and 120 Volts.
Product Features
- Decora Brand Styling: Provides a modern aesthetic and multiple control options in a single-gang wallbox.
- Combination Device: Integrates a 3-Way switch and an AC receptacle.
- Durable Construction: Made with impact-resistant thermoplastic for long service life.
- Double-Wipe Contacts: Ensures reliable electrical connection.
- Grounding: Equipped with grounding for enhanced safety.
- Side Wiring: Designed for convenient side wire connections.
Package Contents
- One (1) Leviton 5645-W Decora 3-Way/AC Combination Switch
- Installation Screws
- Instruction Sheet (this manual)
Installation Instructions
Before proceeding, ensure power is OFF at the circuit breaker or fuse panel. Verify power is off using a voltage tester.
Wiring Diagram Overview
Image: Front view of the Leviton 5645-W Decora 3-Way/AC Combination Switch, showing the rocker switch at the top and the AC receptacle at the bottom. Various wiring terminals (brass, silver, green) are visible on the sides, indicating connections for line, load, common, and ground wires.
Wiring Steps:
- Prepare Wires: Strip approximately 1/2 inch (12.7 mm) of insulation from each wire.
- Identify Wires:
- Ground Wire (Green or Bare Copper): Connect to the green grounding screw on the device.
- Common Wire (from power source): For 3-way applications, one common wire connects to one of the brass screws.
- Traveler Wires (between 3-way switches): Connect to the remaining brass screws.
- Hot Wire (from power source for receptacle): If you want the receptacle to be always hot, connect a separate hot wire to one of the silver screws.
- Load Wire (to light fixture/device controlled by switch): Connect to the remaining silver screw.
Note: The common terminal is shunted internally to all switches. For specific wiring configurations (e.g., independent switch and receptacle power), consult a qualified electrician or refer to advanced wiring diagrams.
- Connect Wires: Loosen the terminal screws, insert the stripped wire ends under the screw heads, and tighten securely. Ensure no bare wire is exposed outside the terminal.
- Mount Device: Carefully fold wires into the wallbox. Mount the device into the wallbox using the provided mounting screws.
- Install Wallplate: Attach a compatible Decora wallplate (not included) over the device.
- Restore Power: Turn power back ON at the circuit breaker or fuse panel.
- Test Operation: Test both the switch and the receptacle to ensure proper functionality.
Operating Instructions
- Switch Operation: Press the top or bottom of the rocker switch to turn the connected light fixture or device ON or OFF. In a 3-way setup, the light can be controlled from two different locations.
- Receptacle Operation: Plug any 120V AC compatible electrical device into the bottom receptacle. The receptacle can be wired to be always ON, or controlled by the switch, depending on your installation.
Maintenance
- This device requires no routine maintenance.
- To clean, wipe with a damp cloth. Do not use abrasive cleaners or solvents.
- Ensure power is OFF at the circuit breaker before cleaning.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Switch does not operate light. |
|
|
| Receptacle has no power. |
|
|
| Switch feels stiff or clunky. | Normal operation for some combination switches. | This may be normal. If functionality is impaired, contact support. |
Specifications
| Model Number: | 5645-W |
| Current Rating: | 15 Amps |
| Operating Voltage: | 120 Volts AC |
| Switch Type: | 3-Way / AC Combination |
| Operation Mode: | Manual |
| Material: | Thermoplastic, Copper (contacts) |
| Wiring Type: | Side Wiring |
| Approvals: | UL, CSA |
| Application: | Residential, Commercial |
Warranty and Support
Leviton offers a Limited Two-Year Warranty for this product. For warranty claims, technical support, or further assistance, please contact Leviton Customer Service.
Leviton Customer Service:
- Refer to the official Leviton website for current contact information.
- When contacting support, please have your product model number (5645-W) available.
