Introduction
The Harmar Mobility AL105 Swing Away Bracket is an essential accessory designed to enhance the functionality of your vehicle's mobility lift system. It allows you to pivot an unoccupied outside lift away from your vehicle, providing unobstructed access to the trunk, lift gate, or tailgate. This manual provides detailed instructions for the setup, operation, and maintenance of your AL105 Swing Away Bracket.
Important Safety Information
WARNING: This product can expose you to chemicals including lead and lead components, which are known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, please visit www.p65warnings.ca.gov/.
Always ensure the swing away bracket is securely latched in both the stowed and open positions before driving or accessing the vehicle's rear. Do not exceed the specified weight capacity of your mobility lift or the swing away bracket.
Setup and Installation
The Harmar AL105 Swing Away Bracket is designed for mounting on a Class III trailer hitch. While installation can be performed by individuals with basic auto repair knowledge, professional installation is recommended to ensure proper function and safety.
Installation Steps:
- Ensure your vehicle is parked on a level surface and the engine is off.
- Insert the AL105 Swing Away Bracket into your vehicle's Class III trailer hitch receiver.
- Secure the bracket using the appropriate hitch pin and clip (not included).
- Attach your compatible Harmar Outside Carrier or Lift to the AL105 Swing Away Bracket according to the lift's specific instructions.
- Verify all connections are tight and secure before use.
Image: The Harmar AL105 Swing Away Bracket securely attached to a vehicle's hitch, ready for use or with a lift attached.
The installed weight of the AL105 bracket itself is approximately 40 lbs. When combined with a mobility lift, ensure your vehicle's hitch capacity is not exceeded.
Operating Instructions
The AL105 Swing Away Bracket provides convenient access to your vehicle's rear cargo area without removing the entire mobility lift. This operation should only be performed when the mobility lift is unoccupied.
To Swing the Bracket Away:
- Ensure the mobility device is removed from the lift.
- Locate the release mechanism on the swing away bracket. This is typically a lever or pin.
- Engage the release mechanism to unlock the bracket from its stowed position.
- Carefully pivot the entire lift assembly away from the vehicle. The bracket is designed to swing smoothly to the side.
- Once fully swung away, ensure the bracket locks into its open position to prevent accidental movement.
Image: A close-up view of the easy-to-operate release mechanism on the swing away bracket.
Image: The swing away option provides clear access to the vehicle's rear hatch, allowing easy loading and unloading of other items.
Image: The swing away bracket in its fully open position, demonstrating the clearance provided for vehicle access.
To Return the Bracket to Stowed Position:
- Disengage the locking mechanism for the open position.
- Carefully pivot the lift assembly back towards the vehicle until it aligns with the hitch.
- Ensure the bracket securely latches into its stowed position. A distinct click or visual indicator confirms it is locked.
Image: The swing away bracket and lift returned to the stowed position, ready for transport.
Maintenance
Regular maintenance ensures the longevity and safe operation of your Harmar AL105 Swing Away Bracket.
- Inspection: Periodically inspect all bolts, pins, and moving parts for wear, damage, or looseness. Tighten any loose fasteners.
- Cleaning: Keep the bracket clean from dirt, road salt, and debris. Use a mild soap and water solution, then rinse thoroughly and dry.
- Lubrication: Apply a small amount of general-purpose grease to pivot points and moving components every few months, or more frequently in harsh conditions, to ensure smooth operation and prevent seizing.
- Corrosion Protection: If any paint chips or scratches are observed, touch them up to prevent rust and corrosion, especially on metal surfaces.
Troubleshooting
- Difficulty Swinging: If the bracket is hard to pivot, check for obstructions, dirt buildup, or lack of lubrication at the pivot points. Apply grease as per maintenance instructions.
- Rattling Noises: Rattling can indicate loose connections. Inspect all bolts and the hitch pin for tightness. Ensure the bracket is fully latched in both stowed and open positions.
- Bracket Not Locking: Verify that the locking mechanisms are free of debris and are fully engaging. Adjustments may be necessary if components are bent or worn.
- General Wear: If significant wear or damage is observed on any structural components, discontinue use and contact Harmar customer support or a certified technician for inspection and repair.
Specifications
| Feature | Detail |
|---|---|
| Model Number | AL105 |
| Product Dimensions | 42 x 17 x 5 inches |
| Installed Weight | 40 pounds |
| Hitch Class Compatibility | Class III |
| Material Type | Aluminum |
| Mounting Type | Hitch Mount |
| Color | Black |
| Compatibility | Most Harmar Outside Carriers or Lifts |
Warranty and Support
For warranty information, technical support, or to purchase replacement parts, please contact Harmar Mobility customer service. Refer to your original purchase documentation for specific warranty terms and contact details. You can also visit the official Harmar website for further assistance.
