Introduction
This manual provides essential information for the safe installation, operation, and maintenance of your KING W1210-W W Series Wall Heater. Please read all instructions carefully before installation and use. This heater is designed for supplemental heating in residential and commercial spaces, featuring an efficient impeller-style fan and a NiChrome heating element for quick heat transfer.
Figure 1: Front view of the KING W1210-W W Series Wall Heater.
Important Safety Information
WARNING: Risk of fire, electric shock, or injury to persons. Improper installation or use can lead to serious injury or death. Always follow these safety guidelines:
- Read all instructions before installing or using this heater.
- This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains, at least 3 feet (0.9 m) from the front of the heater, and keep them away from the sides and rear.
- Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
- Do not operate any heater after it malfunctions, has been dropped, or damaged in any manner. Disconnect power at service panel and have heater inspected by a reputable electrician before reusing.
- Do not use outdoors.
- To disconnect heater, turn controls to off, and turn off power to heater circuit at main disconnect panel.
- Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
- To prevent a possible fire, do not block air intakes or exhaust in any manner.
- A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable vapors or liquids are used or stored.
- Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
- This heater includes a Patented Smart Limit Protection feature to prevent overheating.
Product Features
- Economically Built for Maximum Comfort
- NiChrome Open Coil Element for Quick Heat Transfer
- Dual Wattage Design (specific to model, 1000W for this variant)
- C-Frame Motor
- 4-Blade Aluminum Fan
- Patented Smart Limit Protection
- Wall Can w/ QuickSet Stud Tabs (may be purchased separately)
- Proudly Made in the USA with U.S. & Global Materials
Figure 2: Exploded view of the W Series heater, showing the rough-in can, heater housing, and finned grille.
Setup and Installation
IMPORTANT: All wiring procedures and connections must be in accordance with the National Electrical Code (NEC) and local codes. This heater must be installed by a qualified electrician.
- Location Selection: Choose a wall location that is free from obstructions and allows for proper air circulation. Ensure the heater is not directly below a receptacle outlet.
- Rough-in Can Installation: Secure the rough-in can into the wall opening. The can is designed to fit standard 2" x 4" wall construction. Use the QuickSet Stud Tabs for easy mounting.
- Wiring: Connect the electrical supply wires to the heater's terminal block. This model operates on 120 Volts. Ensure the power supply is disconnected at the circuit breaker before beginning any wiring.
- Heater Assembly: Once wiring is complete and secured, insert the heater assembly into the rough-in can.
- Grille Attachment: Secure the finished grille to the heater assembly using the provided screws.
- Thermostat Connection: This heater requires a wall thermostat or an in-built thermostat (sold separately) for operation. Connect the thermostat according to its specific instructions and local electrical codes.
For detailed visual guidance, refer to the official product video below:
Video 1: Overview of the King Electric W Series Wall Heater, showing its design and potential applications. This video is provided by the seller.
Operating Instructions
- Power On: After proper installation by a qualified electrician, restore power to the heater circuit at the main electrical panel.
- Thermostat Control: Adjust the connected wall thermostat to your desired temperature setting. The heater will activate when the room temperature falls below the set point.
- Initial Operation: During the first few minutes of operation, the heater may emit a slight odor due to the burning off of manufacturing residues. This is normal and will dissipate quickly.
- Heat Output: The NiChrome element and aluminum fan work together to provide instant, forced-air heat.
- Shut-off: The heater will automatically turn off once the room reaches the thermostat's set temperature. To completely turn off the heater, set the thermostat to its lowest setting or turn off power at the circuit breaker.
Maintenance
WARNING: Disconnect power at the main service panel before performing any maintenance or cleaning to reduce the risk of electric shock or injury.
- Cleaning: Periodically clean the exterior of the heater with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Internal Cleaning: For internal cleaning, such as removing dust from the fan blades or heating element, it is recommended to consult a qualified service technician.
- Lubrication: The motor is permanently lubricated and requires no additional maintenance.
- Inspection: Regularly inspect the heater for any signs of damage or wear. If any issues are found, discontinue use and contact a qualified electrician.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Heater does not turn on. | No power to the unit; Thermostat set too low; Circuit breaker tripped; Smart Limit Protection activated. | Check circuit breaker; Increase thermostat setting; Reset circuit breaker; Turn off power at breaker for a few minutes to reset Smart Limit Protection. |
| Insufficient heat output. | Thermostat set too low; Airflow blocked; Heater size inadequate for room. | Increase thermostat setting; Ensure no obstructions to air intake/exhaust; Consider supplemental heating or a higher wattage unit if room size exceeds heater capacity. |
| Unusual noise during operation. | Loose components; Fan obstruction; Normal operating sounds. | Ensure grille is securely fastened; Check for foreign objects (disconnect power first); Some fan noise is normal for forced-air heaters. If noise is excessive or new, contact a qualified technician. |
| Heater cycles on and off frequently. | Thermostat location or calibration; Overheating (Smart Limit Protection). | Ensure thermostat is not in a drafty area or near other heat sources; Check for blocked airflow; If Smart Limit Protection is frequently activating, have the heater inspected by a qualified electrician. |
If troubleshooting steps do not resolve the issue, contact a qualified electrician or the manufacturer's customer support.
Specifications
| Feature | Detail |
|---|---|
| Brand | KING |
| Model Number | W1210-W |
| Power Output | 1000 Watts |
| Voltage | 120 Volts |
| Color | White |
| Form Factor | Wall-mounted |
| Indoor/Outdoor Usage | Indoor |
| Recommended Uses | Home, Office |
| Mounting Type | Wall Mount |
| Heating Coverage | Up to 200 square feet |
| Fuel Type | Electric |
| Special Feature | Overheat Protection |
| Item Weight | 8 pounds |
| Product Dimensions | 4 x 10 x 13.5 inches |
| Material | Metal |
Warranty Information
This KING W1210-W W Series Wall Heater comes with a 1-Year Limited Warranty. Please refer to the warranty documentation included with your product for full terms and conditions. Keep your purchase receipt as proof of purchase for warranty claims.
Customer Support
For technical assistance, replacement parts, or warranty inquiries, please contact KING customer support. Visit the official KING website for contact information or refer to the documentation provided with your heater.
Online Resources: Visit the KING Store on Amazon
