1. Product Overview
The Weller PH50 Soldering Stand and Sponge ESD is an essential accessory designed to safely hold your soldering iron when not in use and to provide a convenient method for cleaning the soldering tip. This stand is specifically engineered for compatibility with Weller PES50 and PES51 irons, ensuring a secure fit and optimal performance. It includes a durable base, a spring-style iron holder, and a cleaning sponge.
1.1 Key Features
- Dedicated soldering tool stand for safe iron placement.
- Designed for use with Weller PES50 and PES51 irons.
- Includes a sturdy base, a spring-coil iron receptacle, and a cleaning sponge.
- Compact dimensions for efficient workspace utilization.
1.2 Product Components
Figure 1.1: Weller PH50 Soldering Stand Components. This image displays the Weller PH50 soldering stand, consisting of a black plastic base with a rectangular recess for the sponge and a metal spring-coil holder for the soldering iron. The yellow cleaning sponge is visible within its designated area in the base.
Figure 1.2: Weller PH50 Soldering Stand Dimensions. This image illustrates the approximate dimensions of the Weller PH50 soldering stand, showing a length of 6.3 inches (16 cm) for the base. This provides a visual reference for the stand's footprint.
2. Safety Information
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Always observe general safety precautions when working with soldering equipment. Ensure adequate ventilation in your workspace. Avoid direct contact with hot soldering iron tips and molten solder. Always place the soldering iron securely in the stand when not actively soldering to prevent accidental burns or damage to surfaces.
3. Setup
- Unpack Components: Carefully remove the soldering stand base, spring-coil iron holder, and cleaning sponge from the packaging.
- Assemble Iron Holder: Insert the straight end of the spring-coil iron holder into the designated hole on the soldering stand base. Ensure it is firmly seated and stable.
- Place Sponge: Place the dry cleaning sponge into the rectangular recess in the stand's base.
- Prepare Sponge: Before first use and periodically during operation, lightly dampen the sponge with clean water. The sponge should be moist, not soaking wet. Excess water can be squeezed out. A damp sponge is crucial for effective tip cleaning.
- Position Stand: Place the assembled soldering stand on a stable, heat-resistant surface near your soldering workstation.
4. Operating Instructions
The Weller PH50 stand provides a safe and convenient resting place for your soldering iron and a means to clean its tip.
- Iron Placement: When not actively soldering, always place your Weller PES50 or PES51 iron securely into the spring-coil holder. Ensure the hot tip is fully contained within the coil and does not touch any other surfaces.
- Tip Cleaning: To clean the soldering iron tip, gently wipe the hot tip across the damp sponge. This will remove excess solder, flux residue, and oxidation, helping to maintain a clean, tinned tip for optimal heat transfer and solder flow.
5. Maintenance
Regular maintenance of your soldering stand and sponge will ensure its longevity and effective performance.
- Sponge Maintenance:
- Keep the sponge damp during use. If it dries out, re-moisten it with clean water.
- Periodically rinse the sponge thoroughly under running water to remove accumulated solder and flux residue. Squeeze out excess water before returning it to the stand.
- Replace the sponge when it becomes heavily worn, torn, or no longer effectively cleans the tip.
- Stand Cleaning:
- Wipe down the stand base with a damp cloth to remove dust and debris.
- Ensure no solder splashes accumulate on the stand, as this can affect its appearance and potentially its stability.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Sponge not cleaning tip effectively. | Sponge is dry or saturated with residue. | Dampen the sponge with clean water or rinse it thoroughly to remove residue. Replace if heavily worn. |
| Soldering iron feels unstable in the holder. | Iron not fully seated or holder is loose. | Ensure the iron is fully inserted into the spring-coil. Check that the spring-coil holder is firmly seated in the base. |
| Stand slides on workbench. | Surface is too smooth or stand feet are dirty. | Place the stand on a non-slip mat or clean the bottom of the stand. |
7. Specifications
| Attribute | Detail |
|---|---|
| Model Number | PH50 |
| Brand | Weller |
| Compatible Irons | Weller PES50, PES51 |
| Item Weight | 14.6 ounces (approx. 413 grams) |
| Product Dimensions (L x W x H) | 3.75 x 3.25 x 7.75 inches (approx. 9.5 x 8.3 x 19.7 cm) |
| Material | Sponge (for cleaning), Metal (holder), Plastic (base) |
| Power Source | Hand Powered (for stand function) |
| Included Components | Stand base, spring-coil holder, cleaning sponge |
| UPC | 013227205561, 037103161093 |
8. Warranty and Support
For detailed warranty information and customer support regarding your Weller PH50 Soldering Stand, please refer to the official Weller website or contact Weller customer service directly. Warranty terms and conditions may vary by region and purchase date.
You can visit the official Weller store for more information and product resources: Weller Official Store
