Introduction
This manual provides comprehensive instructions for the safe and effective use of the Rust-Oleum 203022 Precision-Line Inverted Marking Spray Paint. This product is a solvent-based aerosol paint designed for clear, vivid markings with a precision-line spray tip. It offers quick drying and minimal overspray, making it suitable for various marking applications on surfaces such as concrete, pavement, and grass.
Figure 1: Rust-Oleum Precision-Line Inverted Marking Spray Paint can, APWA Caution Blue. This image displays the product can, highlighting its 'Precision Line' feature and suitability for concrete, pavement, and grass.
Safety Information
Always prioritize safety when using aerosol spray paint. Failure to follow safety precautions can result in injury or property damage.
- Ventilation: Use in a well-ventilated area. Avoid breathing vapors.
- Flammability: This product is extremely flammable. Keep away from heat, sparks, open flames, and other ignition sources. Do not smoke while using.
- Eye Protection: Wear safety glasses with side shields to protect eyes from accidental spray.
- Skin Protection: Wear gloves and protective clothing to prevent skin contact. Wash hands thoroughly after handling.
- Storage: Store in a cool, dry place away from direct sunlight and temperatures above 120°F (49°C). Keep out of reach of children and pets.
- Disposal: Dispose of empty cans according to local regulations. Do not puncture or incinerate.
- Proposition 65 Warning: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Setup
Proper preparation ensures optimal performance and safety.
- Surface Preparation: Ensure the surface to be marked is clean, dry, and free of loose debris for best adhesion and visibility.
- Shake Can: Shake the aerosol can vigorously for at least one minute after the mixing ball begins to rattle. Continue shaking occasionally during use.
- Clear Nozzle: Before first use, or if the nozzle is clogged, invert the can and spray for a few seconds onto a scrap surface to clear the valve.
- Attach Applicator (Optional): For extended reach and consistent lines, attach the can to a compatible marking wand (e.g., True Value #542-363) or marking pistol (e.g., True Value #542-326). Ensure the can is securely seated in the applicator.
Operating Instructions
Follow these steps for effective marking.
- Invert Can: This product is designed for inverted use. Hold the can upside down, with the spray tip facing the ground.
- Position: Hold the can approximately 4-10 inches (10-25 cm) from the surface to be marked. Adjust distance for desired line width and intensity.
- Spray: Press the actuator button firmly to begin spraying. Move the can at a steady pace along the desired path to create a consistent line.
- Drying Time: The paint dries to the touch in less than 5 minutes under normal conditions. Allow adequate time before exposing to traffic or elements.
- Layering: For bolder lines or increased visibility, apply multiple thin coats rather than one thick coat. Allow brief drying time between coats.
Maintenance
Proper maintenance extends the life of your product and ensures consistent performance.
- Clear Spray Tip: After each use, invert the can and spray for 2-3 seconds until only clear propellant comes out. This prevents the nozzle from clogging.
- Storage: Store the can upright in a cool, dry, well-ventilated area. Avoid extreme temperatures.
- Inspect Can: Periodically check the can for any signs of damage or leaks. Do not use damaged cans.
Troubleshooting
Common issues and their solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| No spray or weak spray | Clogged nozzle, insufficient shaking, low can pressure | Shake can vigorously. Invert and spray to clear nozzle. If still no spray, replace can. |
| Uneven or spluttering spray | Inadequate shaking, partially clogged nozzle | Shake can thoroughly. Clear nozzle as described in Maintenance. |
| Paint runs or drips | Spraying too close to surface, applying too thick a coat | Increase distance from surface. Apply lighter, more even coats. |
Specifications
| Brand | Rust-Oleum |
| Model Name | 203022 |
| Color | APWA Caution Blue |
| Size | 17 Ounce (Pack of 1) |
| Item Volume | 17 Fluid Ounces |
| Paint Type | Aerosol Spray, Solvent Based |
| Finish Type | Gloss |
| Specific Uses | Interior/Exterior Marking |
| Surface Recommendation | Concrete, Pavement, Grass, Masonry |
| Drying Time | Less than 5 minutes (to touch) |
| Item Weight | 1.0 pounds |
| Product Dimensions | 2.5"L x 2.5"W x 9.5"H |
| UPC | 020066112608 |
Warranty Information
Specific warranty details for the Rust-Oleum 203022 Precision-Line Inverted Marking Spray Paint are not provided in the product information. Please refer to the manufacturer's official website or contact their customer service for current warranty policies.
Support Information
For further assistance, technical support, or product inquiries, please contact Rust-Oleum directly.
- Manufacturer: Rust-Oleum
- Website: Visit the official Rust-Oleum website for product data sheets, safety information, and contact details.
- Customer Service: Refer to the contact information provided on the product label or the manufacturer's website.
