Cooper-Atkins SRH77A-ONLY-E

Download PDF
Contents

Cooper-Atkins SRH77A-ONLY-E 1 and 2 Zone Temperature/Humidity Thermistor Instrument User Manual

Model: SRH77A-ONLY-E

Introduction

This manual provides detailed instructions for the proper use and maintenance of your Cooper-Atkins SRH77A-ONLY-E Thermistor Instrument. This device is designed for accurate temperature and humidity measurements across one or two zones, featuring a backlight display, sealed keypad, and Min/Max memory functions. Please read this manual thoroughly before operating the instrument.

Safety Information

Observe the following safety precautions to ensure safe operation and to prevent damage to the instrument:

  • This unit is not waterproof. Do not immerse it in water.
  • If the unit becomes wet inside due to cleaning, rain, or condensation, unreliable readings may occur.
  • Do not use the instrument for purposes other than its intended use as a temperature and humidity measurement device.
  • Replace the battery promptly when the 'LO P' indicator appears to ensure accurate readings.

Product Overview

The Cooper-Atkins SRH77A-ONLY-E is a versatile thermistor instrument designed for precise temperature and humidity monitoring. Key features include:

  • Backlight Display: For improved visibility in low-light conditions.
  • Sealed Keypad: Protects the instrument from spills and dust.
  • Min/Max Memory: Records the minimum and maximum readings.
  • Auto Shut-Off: Conserves battery life after 15 minutes of non-use or continuous ON mode.
  • Temperature Differential: Measures the difference between two temperature probes.
  • %RH and Wet Bulb: Provides relative humidity and wet bulb temperature readings.
  • Battery Eliminator Jack: Allows for external power supply (adapter not included).
Cooper-Atkins SRH77A-ONLY-E Thermistor Instrument in its protective blue case, open to show the digital display and control buttons.

Image: The SRH77A-ONLY-E instrument displayed within its protective blue case, showing the digital screen, control buttons, and internal instructions.

Setup

1. Battery Installation

  • The instrument requires one 9-volt NEDA 1604 or equivalent alkaline battery.
  • Open the battery compartment located on the back of the unit.
  • Connect the 9-volt battery to the battery clip, observing correct polarity.
  • Place the battery into the compartment and close the cover securely.

2. Probe Connection

  • For temperature measurements, insert the thermistor probe(s) into the T1 and/or T2 jacks.
  • For humidity measurements, insert the humidity probe into the T3 jack.

Operating Instructions

1. Power On/Off

  • To turn the unit ON, press the ON/OFF button.
  • To turn the unit OFF, press and hold the ON/OFF button for 3 seconds.

2. Temperature Measurement

  • Ensure a temperature probe is inserted into the T1 or T2 jack.
  • Press the TEMP 1 or TEMP 2 button to display the temperature reading for the respective zone.
  • The display will show the current temperature. If no probe is connected, the display will show '----'.

3. Humidity Measurement

  • Ensure a humidity probe is inserted into the T3 jack.
  • Press the RH button to display the relative humidity (%RH) reading.

4. Min/Max Memory

  • Press the MIN/MAX button to display the minimum and maximum recorded readings.
  • Press the MIN/MAX button again to clear the memory and reset for new readings.

5. Temperature Differential

  • With probes in T1 and T2, press the DIFF button to display the temperature difference between probe T1 and T2.

6. Wet Bulb Temperature

  • With a humidity probe in T3, press the WET BULB button to display the calculated wet bulb temperature.

7. Backlight

  • Press the LIGHT/DC button to illuminate the display backlight.
  • To turn the backlight off, press the LIGHT/DC button three times within 5 seconds.

Maintenance

  • To clean the instrument, wipe the exterior with a damp cloth. Do not use abrasive cleaners or immerse the unit in water.
  • Store the instrument in a dry environment when not in use.
  • Replace the 9-volt battery when the 'LO P' indicator appears on the display to ensure continued accuracy.

Troubleshooting

IssuePossible Cause / Solution
'LO P' displayedLow battery power. Replace the 9-volt NEDA 1604 or equivalent alkaline battery.
'HI P' displayedHigh battery power. This is less common but indicates a power issue. Ensure correct battery type and installation.
Temperature reading shows '----' or is inaccurate
  • Probe not properly connected to the T1/T2 jack.
  • Temperature being monitored is outside the instrument's range (-40°F to 300°F).
  • Probe is damaged or faulty.
  • Unit may have been exposed to moisture internally.
Humidity reading shows '----' or is inaccurate
  • Humidity probe not properly connected to the T3 jack.
  • Humidity being monitored is above 95% RH.
  • Humidity probe is damaged or faulty.
  • Unit may have been exposed to moisture internally.
Unit does not turn onBattery is dead or incorrectly installed. Check battery and replace if necessary.

Specifications

FeatureSpecification
Model NumberSRH77A-ONLY-E
Temperature Range-40°F to 300°F (-40°C to 150°C)
Humidity Measurement Range10 to 95% RH (30 to 130°F / 1 to 54°C)
Power Source9-volt Battery Powered
Display TypeDigital
Outer MaterialPlastic
Package Dimensions9.41 x 8.03 x 3.54 inches
Weight1.1 Pounds

Warranty and Support

Cooper-Atkins Corporation warrants this instrument to be free from defects in materials and workmanship for a specified period from the date of purchase. For specific warranty details, technical support, or service inquiries, please contact Cooper-Atkins customer service directly. Keep your proof of purchase for warranty claims.

For further assistance, please visit the official Cooper-Atkins website or contact their customer support.

© 2023 Cooper-Atkins Corporation. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.