Ushio FDF 500W 120V 3200K Clear Lamp

Download PDF
Contents

Ushio FDF 500W 120V 3200K Clear Halogen Lamp Instruction Manual

Model: 581140

Introduction

Welcome to the instruction manual for your Ushio FDF 500W 120V 3200K Clear Halogen Lamp. This lamp is designed for professional lighting applications, including compatibility with Arri Soft Light fixtures. Please read this manual carefully before installation and operation to ensure safe and optimal performance.

Safety Information

To prevent injury or damage, always observe the following safety precautions:

  • Always disconnect power before installing, replacing, or cleaning the lamp.
  • Halogen lamps operate at high temperatures. Avoid touching the lamp directly during or immediately after operation. Allow sufficient cooling time.
  • Use protective gloves when handling the lamp to prevent oils from skin transferring to the glass, which can cause hot spots and reduce lamp life.
  • Ensure the lamp is securely seated in the fixture.
  • Do not exceed the specified voltage (120V) or wattage (500W) for your fixture.
  • Dispose of used lamps according to local regulations.

Product Overview

The Ushio FDF 500W 120V 3200K Clear Halogen Lamp is a high-quality light source known for its consistent color temperature and reliable performance in professional lighting environments.

Key Features:

  • Watts: 500W
  • Volts: 120V
  • Color Temperature: 3200K
  • Finish: Clear
  • Average Life: 400 hours
  • Maximum Overall Length: 4.68 inches
  • Compatibility: Designed to fit Arri Soft Light fixtures.
Ushio FDF 500W 120V 3200K Clear Halogen Lamp

Image: The Ushio FDF 500W 120V 3200K Clear Halogen Lamp, showing its clear glass envelope and base. This lamp is suitable for professional lighting applications.

Setup and Installation

Follow these steps to safely install your Ushio FDF halogen lamp:

  1. Power Disconnection: Ensure the lighting fixture is completely powered off and unplugged from the electrical outlet.
  2. Cooling: If replacing an old lamp, allow the fixture and the old lamp to cool down completely before handling.
  3. Handling the Lamp: Wear clean, lint-free gloves or use a clean cloth to handle the new Ushio FDF lamp. Avoid touching the glass envelope directly with bare hands, as oils can cause premature failure.
  4. Insertion: Carefully insert the lamp's pins into the corresponding sockets of the fixture. Ensure the lamp is fully and securely seated. This lamp is specifically designed to fit Arri Soft Light fixtures.
  5. Power Connection: Once the lamp is securely installed, reconnect the fixture to the power supply.
  6. Testing: Turn on the fixture to test the lamp's operation.

Operation

The Ushio FDF 500W 120V 3200K Clear Halogen Lamp is designed for continuous operation within its specified parameters.

  • Power On/Off: Use the fixture's power switch to turn the lamp on or off.
  • Dimming: This lamp is dimmable. If your fixture is equipped with a compatible dimmer, you can adjust the light output as needed. Ensure the dimmer is rated for the lamp's wattage (500W).
  • Heat Output: Be aware that halogen lamps produce significant heat. Ensure adequate ventilation around the fixture during operation to prevent overheating.

Maintenance

Proper maintenance ensures optimal performance and extends the life of your lamp.

  • Cleaning: Periodically inspect the lamp and fixture for dust or debris. With the power off and the lamp cool, gently wipe the glass envelope with a clean, dry, lint-free cloth if necessary. Do not use liquid cleaners.
  • Replacement: Replace the lamp when it reaches the end of its average life (approximately 400 hours) or if it fails. Follow the installation steps for replacement.
  • Inspection: Regularly check the lamp's pins and the fixture's sockets for any signs of wear or damage.

Troubleshooting

Refer to the table below for common issues and their solutions.

ProblemPossible CauseSolution
Lamp does not lightNo power to fixtureCheck power connection and circuit breaker.
Lamp does not lightLamp not properly seatedDisconnect power, allow to cool, re-seat lamp.
Lamp does not lightLamp is burned outDisconnect power, allow to cool, replace lamp.
Lamp flickers or dims unexpectedlyLoose connectionDisconnect power, allow to cool, check lamp seating and fixture wiring.
Lamp flickers or dims unexpectedlyIncompatible or faulty dimmerEnsure dimmer is rated for 500W and is functioning correctly.
Reduced lamp lifeImproper handling (fingerprints)Always handle with gloves or a clean cloth.
Reduced lamp lifeOver-voltage or excessive vibrationEnsure correct voltage supply and minimize vibration.

Specifications

Detailed technical specifications for the Ushio FDF 500W 120V 3200K Clear Halogen Lamp:

FeatureDetail
BrandUshio
Model Number581140
Light TypeHalogen
Wattage500 Watts
Voltage120 Volts
Color Temperature3200 Kelvin
FinishClear
Average Life400 hours
Special FeatureDimmable
Maximum Overall Length4.68 inches
Item Weight2.4 ounces
UPC841606011898
ASINB000KEJG38

Warranty and Support

For warranty information or technical support regarding your Ushio FDF 500W 120V 3200K Clear Halogen Lamp, please refer to the documentation provided with your purchase or contact the retailer or Ushio directly. Keep your proof of purchase for warranty claims.

For general inquiries, you may visit the Ushio official website.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.