Product Overview
The Skyjacker H7060 Softride Hydro Shock Absorber is engineered to provide enhanced vehicle handling, stability, and ride comfort. Its design incorporates multi-stage velocity sensitive valving and twin-tube construction to adapt to varying on and off-road conditions.
This image displays the Skyjacker H7060 Softride Hydro Shock Absorber. It features a white main body with the 'SKYJACKER HYDRO 7000' logo in red and blue. One end of the shock absorber is covered by a bright red corrugated protective boot, while both ends show mounting eyes with red polyurethane bushings.
Setup and Installation
Proper installation of the Skyjacker H7060 Softride Hydro Shock Absorber is crucial for optimal performance and safety. It is recommended that installation be performed by a qualified automotive technician using appropriate tools and safety equipment.
Safety Precautions:
- Always wear appropriate personal protective equipment, including safety glasses and gloves.
- Ensure the vehicle is securely supported on jack stands or a lift before beginning work.
- Never work under a vehicle supported only by a jack.
- Refer to your vehicle's service manual for specific torque specifications and procedures.
Installation Steps (General Guidelines):
- Prepare Vehicle: Park the vehicle on a level surface, engage the parking brake, and block the wheels. Lift the vehicle and support it securely.
- Remove Old Shock Absorber: Locate and remove the mounting bolts for the existing shock absorber. Carefully remove the old unit.
- Inspect Mounting Points: Clean and inspect the mounting points for any damage or wear. Replace any worn components as necessary.
- Install New Shock Absorber: Position the Skyjacker H7060 shock absorber. Ensure the red polyurethane bushings are correctly seated in the mounting eyes. Attach the shock absorber using the appropriate hardware.
- Tighten Fasteners: Torque all mounting bolts to the vehicle manufacturer's specifications. Do not overtighten.
- Lower Vehicle: Carefully lower the vehicle to the ground.
- Final Check: Perform a visual inspection to ensure all components are properly installed and secured.
The shock absorber includes red polyurethane bushings and a red boot for protection and durability. Ensure these components are correctly installed and free from damage during the process.
Operating Principles
The Skyjacker H7060 Softride Hydro Shock Absorber is designed to control unwanted spring motion, providing a smoother and more stable ride. Its key operational features include:
- Multi-Stage Velocity Sensitive Valving: This technology allows the shock absorber to instantly respond to varying road conditions and speeds. It provides a stable and controlled level of resistance, optimizing damping for both rough and smooth terrain.
- Twin Tube Construction: This design enhances durability and heat dissipation, contributing to consistent performance over extended use.
- 5/8 inch Diameter Hardened and Double Chrome Rod: Ensures strength and resistance to wear and corrosion, extending the lifespan of the shock absorber.
These features work in conjunction to keep the vehicle's tires in consistent contact with the road surface, improving handling, stability, and overall driver control.
Maintenance
Regular inspection and basic maintenance can help ensure the longevity and optimal performance of your Skyjacker H7060 Softride Hydro Shock Absorbers.
Recommended Maintenance Schedule:
- Every 6 Months or 6,000 Miles: Visually inspect the shock absorbers.
Inspection Points:
- Leaks: Check for any signs of fluid leakage around the shock body or rod seal. A small amount of oil film is normal, but excessive wetness indicates a leak.
- Bushings: Inspect the red polyurethane bushings at both ends for cracks, tears, or excessive wear. Worn bushings can lead to noise and reduced performance.
- Mounting Hardware: Ensure all mounting bolts and nuts are tight and free from corrosion.
- Protective Boot: Check the red corrugated boot for tears or damage. The boot protects the shock rod from debris.
- Physical Damage: Look for dents, bends, or other damage to the shock body or rod.
Cleaning:
Clean the exterior of the shock absorbers periodically with mild soap and water to remove dirt and road grime. Avoid using harsh chemicals that could damage seals or finishes.
Troubleshooting
If you experience issues with your vehicle's suspension after installing Skyjacker H7060 shock absorbers, consider the following common problems and potential solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Excessive Bouncing / Poor Ride Quality | Worn or damaged shock absorber, incorrect installation, or other suspension component issues. | Inspect shocks for leaks or damage. Verify correct installation and torque. Check other suspension components (springs, control arms). |
| Clunking / Rattling Noise | Loose mounting hardware, worn bushings, or contact with other vehicle components. | Check all mounting bolts for tightness. Inspect bushings for wear and replace if necessary. Ensure adequate clearance around the shock absorber. |
| Fluid Leakage | Damaged seal, internal component failure, or physical damage to the shock body. | A small film of oil is normal. Significant leakage indicates a failed shock absorber that requires replacement. |
| Uneven Ride Height | Not typically caused by shock absorbers alone; more likely related to springs or other suspension components. | Inspect vehicle springs for sagging or breakage. Consult a professional for diagnosis. |
If troubleshooting steps do not resolve the issue, or if you are unsure about any repair, it is recommended to consult a certified automotive technician.
Specifications
| Feature | Detail |
|---|---|
| Brand | Skyjacker |
| Model | H7060 (Hydro Shock Absorber) |
| Auto Part Position | Front |
| Material | Polyurethane (PU) Bushings |
| OEM Part Number | H7060 |
| Item Weight | 6 pounds |
| Product Dimensions | 24 x 3 x 3 inches |
| Construction | Twin Tube |
| Rod Diameter | 5/8 inch (Hardened and Double Chrome) |
| Valving | Multi-Stage Velocity Sensitive |
| Included Components | Red Polyurethane Bushings, Red Boot |
| UPC | 803696140223 |
Warranty Information
Specific warranty details for the Skyjacker H7060 Softride Hydro Shock Absorber are provided by the manufacturer. For comprehensive warranty terms, conditions, and claim procedures, please refer to the documentation included with your purchase or visit the official Skyjacker website. It is recommended to retain your proof of purchase for any warranty claims.
Support
For technical assistance, installation questions, or product support regarding your Skyjacker H7060 Softride Hydro Shock Absorber, please contact Skyjacker customer service directly or reach out to an authorized Skyjacker dealer. When contacting support, please have your product model number (H7060) and purchase information readily available.
Legal Disclaimer
CALIFORNIA WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov