Product Overview
The Taylor Instant Read Wired Probe Digital Thermometer is designed to accurately monitor the internal temperature of food during cooking, especially in ovens or grills, without needing to open the door. It features a durable stainless steel probe connected by a heat-resistant silicone cord to a digital display unit. This thermometer includes preset USDA cooking temperatures for various meats and a customizable setting, along with a timer function and an audible alarm for precise cooking results.
Front view of the Taylor Instant Read Wired Probe Digital Thermometer, showing its display and probe.
Components
- Digital Thermometer Unit
- Stainless Steel Probe (6 inches)
- Silicone Cord (4 feet)
- 1 AAA Battery (pre-installed)
Diagram showing the dimensions of the Taylor Digital Thermometer, including the 4-foot wire length and 5.5-inch probe length.
Setup
Battery Installation
The thermometer requires 1 AAA battery, which is pre-installed. If replacement is needed:
- Locate the battery compartment on the back of the unit.
- Slide the battery cover open.
- Insert 1 AAA battery, ensuring correct polarity (+/-).
- Close the battery cover securely.
Rear view of the thermometer showing the battery compartment and magnetic back.
Probe Connection
Insert the probe's jack firmly into the port on the side of the thermometer unit. Ensure a secure connection for accurate readings.
Operating Instructions
Power On/Off
Press the 'ON' button to turn the thermometer on. To turn off, press and hold the 'ON' button for a few seconds.
Temperature Monitoring
- Insert the stainless steel probe into the thickest part of the food, avoiding bone or gristle.
- Place the thermometer unit outside the oven or grill, allowing the silicone cord to pass through the door seal. The cord is safe up to 485°F (250°C).
- The display will show the 'CURRENT' temperature.
- Use the 'MODE' button to cycle through preset USDA temperatures for beef, poultry, pork, fish, or select 'CUSTOM' for a user-defined target temperature.
- Adjust the 'TARGET TEMP' using the 'Min.' and 'Sec.' buttons.
Close-up of the thermometer display showing preset USDA cooking temperatures for various meats and a timer function.
The Taylor Digital Thermometer placed on a countertop next to an oven, with its probe cord extending into the oven door.
Timer Function
The thermometer can also function as a standalone timer with a range of up to 99 minutes and 59 seconds.
- Press the 'Time/Temp' button to switch to timer mode.
- Use the 'Min.' and 'Sec.' buttons to set the desired countdown time.
- Press 'STOP/START' to begin or pause the timer.
- Press 'CLEAR' to reset the timer.
Temperature Alarm
Once the 'CURRENT' temperature reaches the 'TARGET TEMP', an audible alarm will sound, indicating that your food has reached the desired doneness.
Unit Conversion (°F/°C)
Press the '°F/°C' button on the side of the unit to switch between Fahrenheit and Celsius temperature displays.
Maintenance and Care
- Cleaning: Wipe the thermometer unit clean with a damp cloth. Do not immerse the unit in water. The stainless steel probe can be cleaned with warm, soapy water.
- Probe Care: Always handle the probe carefully. Avoid bending or kinking the cord.
- Storage: Store the thermometer and probe in a dry place when not in use.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No display or dim display | Low or dead battery; incorrect battery installation. | Replace battery; ensure correct polarity. |
| Inaccurate temperature reading | Probe not fully inserted; probe or cord damage; probe not connected securely. | Ensure probe is fully inserted into thickest part of food; check for visible damage; re-insert probe jack firmly. |
| Alarm not sounding | Target temperature not set; volume too low (if applicable). | Set a target temperature; check user manual for volume controls (if any). |
| Timer not working | Timer not started; incorrect time set. | Press 'STOP/START' to begin; ensure time is set correctly. |
Specifications
| Feature | Value |
|---|---|
| Model Name | Instant Read Wired Probe Digital Thermometer |
| Model Number | 1471.00 |
| Temperature Range | -32°F to 392°F (-0°C to 200°C) |
| Probe Material | Stainless Steel |
| Probe Length | 6 Inches |
| Cord Length | 4 Feet (Silicone) |
| Cord Heat Resistance | Up to 485°F (250°C) |
| Display Type | Digital, Backlit LCD |
| Power Source | 1 AAA Battery (included) |
| Timer Range | 99 minutes: 59 seconds |
| Product Weight | 4.8 ounces |
Warranty and Support
This Taylor product comes with a One (1) year limited warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use.
For warranty claims, technical support, or product inquiries, please contact Taylor customer service. Refer to the packaging or the official Taylor website for the most current contact information.
Please retain your purchase receipt as proof of purchase for warranty purposes.
