Ozark Trail 2 Burner Camp Stove Instruction Manual

Introduction

Thank you for purchasing the Ozark Trail 2 Burner Camp Stove. This manual provides important information for the safe operation, maintenance, and troubleshooting of your new camp stove. Please read this manual thoroughly before use and retain it for future reference.

Important Safety Information

WARNING: For outdoor use only. Do not operate this appliance inside any building, garage, or other enclosed area. Failure to follow these instructions could result in fire, explosion, or carbon monoxide poisoning, which could cause property damage, personal injury, or death.

• Always operate the stove on a level, stable, non-combustible surface.
• Keep children and pets away from the stove during operation.
• Do not leave the operating stove unattended.
• Ensure adequate ventilation.
• Keep the area around the stove clear of combustible materials, gasoline, and other flammable vapors and liquids.
• Never connect or disconnect the propane cylinder while the stove is lit or hot.
• Check for gas leaks using a soapy water solution before each use. Never use a flame to check for leaks.
• Use only standard 16.4 oz. propane cylinders.
• Do not modify this appliance. Any modification may be dangerous and will void the warranty.

Parts List

Before assembly, ensure all parts are present and undamaged:

• Stove body with two burners
• Two control knobs (pre-attached)
• Propane regulator assembly
• Grates/pot supports

Note: Standard 16.4 oz. propane cylinder is not included and must be purchased separately.

Setup Instructions

1. Unpack the Stove: Carefully remove all packaging materials.
2. Position the Stove: Place the stove on a firm, level, non-combustible surface outdoors, away from any flammable materials. Ensure there is adequate clearance from walls or other structures.
3. Attach Propane Cylinder:
   • Ensure both burner control knobs are in the "OFF" position.
   • Screw the threaded end of the propane cylinder into the regulator connection on the stove. Hand-tighten only. Do not overtighten.
   • Check for leaks: Apply a soapy water solution to the connection point. If bubbles appear, there is a leak. Tighten the connection or replace the cylinder if necessary. Do not use the stove if a leak is detected.
4. Prepare Cooking Surface: Place the grates/pot supports securely over the burners.

Operating Instructions

1. Lighting a Burner:
   • Ensure the propane cylinder is securely attached and there are no leaks.
   • Turn the control knob for the desired burner slowly to the "LIGHT" or "HIGH" position. You should hear gas flowing.
   • Immediately apply a lit match or a long-nosed lighter to the burner.
   • Once lit, adjust the flame to the desired cooking temperature using the control knob.
   • If the burner does not light within 5 seconds, turn the control knob to "OFF", wait 5 minutes for gas to dissipate, and repeat the lighting procedure.
2. Using Both Burners: Repeat the lighting procedure for the second burner as needed.
3. Turning Off the Stove:
   • Turn both burner control knobs to the "OFF" position.
   • Allow the stove to cool completely before disconnecting the propane cylinder or moving the stove.
   • Once cool, disconnect the propane cylinder by unscrewing it from the regulator.

Care and Maintenance

• Cleaning:
  • Always ensure the stove is completely cool and the propane cylinder is disconnected before cleaning.
  • Wipe down the stove body with a damp cloth and mild detergent. Avoid abrasive cleaners.
  • Remove and clean the grates/pot supports with warm soapy water. Rinse thoroughly and dry completely before reassembling.
  • Keep burner ports clean to ensure efficient operation. Use a soft brush if necessary.
• Storage:
  • Store the stove in a cool, dry place, away from direct sunlight and extreme temperatures.
  • Ensure the propane cylinder is disconnected and stored separately in a well-ventilated area, away from ignition sources.
• Inspection: Regularly inspect the regulator and connections for any signs of damage, cracks, or wear. Replace if necessary.

Troubleshooting

If you encounter problems not listed here, or if solutions do not resolve the issue, please contact Ozark Trail customer support.

Specifications

• Model: 842-A100-W
• Brand: Ozark Trail
• Fuel Type: Liquefied Petroleum Gas (Propane)
• Power Source: Gas Powered
• Burners: 2 Stainless Steel
• Maximum Energy Output: 10,000 British Thermal Units (per burner)
• Material: Stainless Steel
• Item Weight: 16.4 Ounces (0.46 kg)
• UPC: 039953509674

Warranty and Support

For warranty information or technical support, please refer to the product packaging or contact Ozark Trail customer service directly. Keep your purchase receipt as proof of purchase.

Manufacturer: SA