Samson MS100 Studio Monitor Stands Instruction Manual

1. Introduction

The Samson MS100 Studio Monitor Stands are designed to provide stable and adjustable support for studio monitors. Constructed from alloy steel with a powder-coated finish, these stands feature a telescoping column for height adjustment and an adjustable vise-style speaker bracket to accommodate various monitor sizes. The heavy base includes carpet spikes for enhanced stability on different floor surfaces.

2. Package Contents

Please verify that all components are present before assembly:

• MS100 Stand Base
• Telescoping Column Assembly
• Speaker Platform/Vise Bracket
• Carpet Spikes (pre-installed or separate)
• Assembly Hardware (screws, washers, adjustment knobs)

3. Setup and Assembly

Follow these steps to assemble your Samson MS100 Studio Monitor Stands:

1. Unpack Components: Carefully remove all parts from the packaging. Place them on a clean, flat surface.
2. Attach Base: Secure the telescoping column to the stand base using the provided screws and washers. Ensure the connection is tight and stable.
3. Install Speaker Platform: Insert the speaker platform (vise bracket) into the top of the telescoping column. Tighten the adjustment knob to secure it in place.
4. Adjust Carpet Spikes: If your stand includes separate carpet spikes, thread them into the bottom of the base. Adjust them to ensure the stand is level and stable on carpeted surfaces. For hard floors, use the included rubber feet or protective pads.
5. Initial Height Adjustment: Loosen the height adjustment knob on the telescoping column. Extend the column to a desired approximate height and re-tighten the knob securely.

Image 1: Fully assembled Samson MS100 Studio Monitor Stand. This image shows the stand with its heavy base, telescoping column, and adjustable vise-style speaker bracket at the top.

4. Operating Instructions

Proper use and adjustment of your monitor stands:

• Height Adjustment: To adjust the height, loosen the knob on the telescoping column. Carefully raise or lower the upper section to the desired height. Ensure the monitor is not on the stand during this adjustment. Once the desired height is reached, firmly tighten the knob to prevent slippage.
• Speaker Placement: Place your studio monitor onto the vise-style bracket. Adjust the bracket to securely grip the sides of your monitor. Ensure the monitor is centered and balanced on the platform. Tighten any locking mechanisms on the bracket to hold the monitor firmly.
• Stability Check: After placing your monitors and adjusting the height, gently test the stability of each stand. Ensure there is no wobbling or instability. Re-tighten all knobs and connections if necessary.
• Optimal Positioning: Position the stands to create an equilateral triangle between your listening position and the two monitors for optimal stereo imaging.

5. Maintenance

To ensure the longevity and proper function of your Samson MS100 Studio Monitor Stands:

• Cleaning: Wipe down the stands with a soft, dry cloth. Avoid abrasive cleaners or solvents that could damage the finish.
• Regular Inspection: Periodically check all screws, bolts, and adjustment knobs to ensure they are tight. Loose connections can compromise stability.
• Storage: If storing the stands for an extended period, disassemble them and store in a dry, cool place to prevent corrosion or damage.

6. Troubleshooting

Common issues and their solutions:

• Stand is Unstable/Wobbles:
  • Ensure all assembly screws and adjustment knobs are fully tightened.
  • Verify the stand is on a level surface. Adjust carpet spikes or use shims if necessary.
  • Confirm the monitor is properly seated and secured in the vise bracket.
• Height Adjustment Knob Slips:
  • Ensure the knob is tightened firmly. Do not overtighten, but ensure it provides sufficient friction.
  • Check for any debris or damage to the telescoping column or knob mechanism.
• Monitor Not Secure in Bracket:
  • Ensure the vise bracket is adjusted to the correct width for your monitor and fully tightened.
  • Verify your monitor's dimensions are within the compatible range for the MS100 stands.

7. Specifications

8. Warranty and Support

The Samson MS100 Studio Monitor Stands come with a 1-year parts and labor warranty from the date of purchase. This warranty covers manufacturing defects and material flaws under normal use. It does not cover damage caused by misuse, accidents, unauthorized modifications, or normal wear and tear.

For warranty claims, technical support, or further assistance, please contact Samson customer service through their official website or the retailer where the product was purchased. Please have your proof of purchase and model number (SAMS100) available when contacting support.