Introduction
The Leifheit Parat Plus Roll Holder is a wall-mounted kitchen accessory designed to conveniently store and dispense aluminum foil, plastic wrap, paper towels, and freezer bags. It features integrated cutting mechanisms for clean and precise cuts, ensuring easy access to your kitchen essentials.
Key Features:
- Integrated dispensers for aluminum foil, plastic wrap, and paper towels.
- Razor-sharp, hidden special blades for neat foil and wrap ends.
- Additional compartment for freezer bags and a small shelf space for tape or other small items.
- Space-saving wall-mounted design.
- Constructed from durable Polystyrene, ABS Resin, POM Resin, Rubber, Stainless Steel, and PVC.
Setup and Installation
Before installation, ensure you have the necessary tools: a drill, screwdriver, and a level. The roll holder is designed for wall mounting.
Installation Steps:
- Choose Location: Select a suitable wall location in your kitchen, ensuring it's clear of obstructions and within easy reach.
- Mark Drilling Points: Hold the roll holder against the wall at the desired height and use a pencil to mark the positions for the mounting screws. The product dimensions are approximately 15.35 inches (38.5 cm) long and 12.6 inches (31.5 cm) wide. Refer to the diagram for precise measurements.
Image: Dimensions of the Leifheit Parat Plus Roll Holder.
- Drill Holes: Drill holes at the marked points. Insert wall anchors if necessary, depending on your wall material.
- Mount Holder: Secure the roll holder to the wall using the provided screws. Ensure it is level and firmly attached.
Image: Mounting the roll holder to the wall.
- Load Paper Towel Roll: Insert a standard paper towel roll onto the bottom bar.
Image: Loading a paper towel roll.
- Load Foil and Plastic Wrap: Open the top compartments. Insert rolls of aluminum foil and plastic wrap into their respective slots. Ensure the leading edge of the foil/wrap is pulled through the cutting mechanism. Close the compartments securely.
Image: Loading foil and plastic wrap into the upper compartments.
- Load Freezer Bags/Tape: Place freezer bags or a roll of tape into the designated top-right compartment.
Installation and Usage Overview:
Video: A demonstration of installing the Leifheit Parat Plus Roll Holder and loading various rolls, including paper towels, aluminum foil, and plastic wrap, followed by a demonstration of using the integrated cutters.
Operating Instructions
The Leifheit Parat Plus Roll Holder is designed for simple and efficient dispensing and cutting of kitchen wraps.
Using the Cutters:
- For Aluminum Foil and Plastic Wrap:
- Pull the desired length of foil or plastic wrap from its compartment.
- Hold the roll holder steady with one hand.
- With the other hand, slide the cutting mechanism smoothly across the width of the material. The integrated blade will provide a clean, straight cut.
- Ensure the end of the material remains slightly exposed for easy access next time.
Image: Using the integrated cutter for plastic wrap or aluminum foil.
- For Paper Towels:
- Pull down on the paper towel roll to dispense a sheet.
- Tear along the perforated line. The design allows for easy one-handed tearing.
- For Freezer Bags/Tape:
- Access items from the top-right compartment as needed.
Maintenance
Regular cleaning will ensure the longevity and optimal performance of your Leifheit Parat Plus Roll Holder.
- Cleaning: Wipe the exterior surfaces with a damp cloth and mild detergent. Avoid abrasive cleaners or scouring pads, as these can damage the finish.
- Blades: The cutting blades are designed to be self-sharpening and generally do not require maintenance. If residue builds up, carefully wipe the blade area with a damp cloth (exercise caution due to sharp edges).
- Roll Replacement: Replace rolls of foil, plastic wrap, and paper towels as they run out, following the loading instructions in the Setup section.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Foil/Wrap not cutting cleanly. | Material not properly aligned; dull blade (unlikely with integrated design); excessive force or incorrect cutting motion. | Ensure the material is taut and aligned before cutting. Slide the cutter smoothly and evenly across. Check for any debris obstructing the blade. |
| Difficulty loading rolls. | Rolls are too large for the compartment; material not fed correctly through the slot. | Use standard-sized rolls. Ensure the leading edge of the material is fed through the designated slot before closing the compartment. Refer to the loading instructions. |
| Roll holder feels loose on the wall. | Mounting screws are loose; improper installation. | Tighten the mounting screws. If the problem persists, re-evaluate the installation method and consider using appropriate wall anchors for your wall type. |
Product Specifications
- Model Number: 25723
- Brand: Leifheit
- Material: Polystyrene, ABS Resin, POM Resin, Rubber, Stainless Steel, PVC
- Color: White
- Mounting Type: Wall Mount
- Product Dimensions (L x W x D): Approximately 15.35 inches (38.5 cm) x 12.6 inches (31.5 cm) x 2.76 inches (7.0 cm)
- Item Weight: 0.35 Ounces
- UPC: 047738257238, 781147752198, 882524797044
Warranty Information
The Leifheit Parat Plus Roll Holder comes with a 3-year warranty from the date of purchase. This warranty covers manufacturing defects under normal use. Please retain your proof of purchase for any warranty claims. For detailed terms and conditions, please refer to the official Leifheit website or contact customer support.
Customer Support
For further assistance, questions, or to report any issues not covered in this manual, please contact Leifheit customer support:
- Website: Visit the official Leifheit website for FAQs and contact information.
- Contact Form: Use the contact form available on the Leifheit support page.
- Phone: Refer to the Leifheit website for regional customer service phone numbers.
When contacting support, please have your product model number (25723) and proof of purchase readily available.
