1. Introduction
This manual provides detailed instructions for the safe installation, operation, and maintenance of your Leviton R62-05634-0WS 15 Amp White Decora Dual Switch. Please read this manual thoroughly before beginning installation and retain it for future reference.
Image 1.1: Front view of the Leviton R62-05634-0WS 15 Amp White Decora Dual Switch, showing the two independent rocker switches and side terminals.
2. Safety Information
WARNING: RISK OF ELECTRIC SHOCK. Improper installation can result in serious injury or death. Always turn off power at the circuit breaker or fuse box before wiring. Installation should be performed by a qualified electrician or in accordance with local electrical codes.
- Ensure the power supply is disconnected before installation or servicing.
- Use only with copper or copper-clad wire.
- Do not exceed the maximum electrical ratings of 15 Amps and 120 Volts AC.
- This device is intended for indoor use only.
- Ensure all wire connections are secure and properly insulated.
3. Package Contents
- One (1) Leviton R62-05634-0WS 15 Amp White Decora Dual Switch
- Mounting Screws
- Instruction Sheet (this manual)
4. Product Features
- Dual Control: Two independent single-pole switches in a single Decora device.
- Current Rating: 15 Amps.
- Voltage Rating: 120 Volts AC.
- Wiring: Side-wired terminals for easy installation.
- Actuator Type: Rocker style for smooth operation.
- Design: Decora styling for a modern aesthetic.
5. Installation and Setup
Before you begin, ensure the power is OFF at the circuit breaker or fuse box.
- Turn Off Power: Locate the circuit breaker or fuse that controls the power to the switch location. Turn it OFF. Verify power is off using a voltage tester.
- Remove Old Switch: Carefully remove the wallplate and unscrew the existing switch from the electrical box. Disconnect the wires from the old switch, noting their connections (e.g., line, load 1, load 2, ground).
- Prepare Wires: If necessary, strip approximately 1/2 inch (12.7 mm) of insulation from the ends of the wires.
- Wire Connections:
- Ground Wire: Connect the bare copper or green insulated ground wire from the electrical box to the green ground screw on the switch.
- Line (Hot) Wire: Connect the incoming hot wire (usually black) to one of the brass-colored screw terminals. This switch has two independent switches, so you will typically have one incoming hot wire that needs to be pigtailed to feed both switches, or connect to a common terminal if provided (this model has side terminals, implying individual connections). Consult a qualified electrician if unsure.
- Load Wires: Connect the load wires (wires going to the light fixture or appliance) to the remaining brass-colored screw terminals. Each rocker switch controls one load. Ensure the correct load wire is connected to the desired switch terminal.
Note: This switch is designed for 1-way circuits. For 3-way or 4-way applications, different switch types are required.
- Mount Switch: Carefully fold the wires into the electrical box. Insert the switch into the box and secure it with the provided mounting screws.
- Install Wallplate: Attach the Decora wallplate (sold separately) over the switch.
- Restore Power: Turn the power back ON at the circuit breaker or fuse box.
- Test Operation: Test both switches to ensure they control the intended loads correctly.
6. Operating Instructions
The Leviton R62-05634-0WS features two independent rocker switches. To operate:
- Press the top or bottom portion of either rocker switch to toggle the connected load (e.g., light, fan) ON or OFF.
- Each rocker operates independently, allowing control of two separate devices from a single location.
7. Maintenance
The Leviton Decora Dual Switch requires minimal maintenance.
- Cleaning: To clean the switch and wallplate, wipe with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Inspection: Periodically inspect the switch for any signs of damage or loose connections. If any issues are observed, turn off power and consult a qualified electrician.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Switch does not operate. | No power to the switch. Loose wire connection. Faulty switch. | Check circuit breaker/fuse. Turn off power and check all wire connections. Replace switch if necessary (after verifying power and connections). |
| Only one switch operates. | Incorrect wiring for the non-operating switch. Faulty load or bulb. | Turn off power and verify load wire connection for the non-operating switch. Check the bulb or connected appliance. |
| Switch feels loose in the wall box. | Mounting screws are not tight. | Turn off power and tighten mounting screws. |
If troubleshooting steps do not resolve the issue, consult a qualified electrician.
9. Specifications
| Attribute | Detail |
|---|---|
| Model Number | R62-05634-0WS |
| Brand | Leviton |
| Operation Mode | ON-OFF |
| Current Rating | 15 Amps |
| Operating Voltage | 120 Volts AC |
| Contact Type | Make-before-break |
| Connector Type | Side Terminals |
| Terminal Type | Side-terminated |
| Circuit Type | 1-way |
| Actuator Type | Rocker Actuator |
| Contact Material | Metal |
| International Protection Rating | IP00 |
| Number of Positions | 2 (for dual switch) |
| Control Method | Touch |
| UPC | 078477774069 |
10. Warranty Information
Leviton products are backed by a limited warranty. For specific warranty terms and conditions, please refer to the warranty statement included with your product packaging or visit the official Leviton website. Keep your proof of purchase for warranty claims.
11. Support
For technical assistance or further information, please contact Leviton Customer Service:
- Website: www.leviton.com
- Phone: Refer to the Leviton website for regional contact numbers.
