AUTO METER 233904

Download PDF
Contents

AUTO METER 233904 Autogage Monster Shift-Lite Tachometer Instruction Manual

Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of your AUTO METER 233904 Autogage Monster Shift-Lite Tachometer. This instrument is designed for performance enthusiasts, offering precise RPM readings and a user-programmable shift light.

Key features include traditional incandescent lighting for clear visibility, compatibility with both 12 and 16-volt electrical systems, and a rapid-response air-core electric tachometer capable of going from 0 to full scale in 333 milliseconds. It is compatible with 2-4 pulse ignition signals, suitable for 4-8 cylinder engines, and works with points, electronic, and most 12V high-performance racing ignitions. The user-programmable shift light assists in optimizing engine power band utilization and improving vehicle performance during gear changes.

What's in the Box

Upon unpacking, verify that all components are present:

  • Tachometer head
  • Mounting bracket
  • Bracket pedestal
  • Shift light

Setup and Installation

Proper installation is crucial for accurate operation and longevity of your tachometer. If you are unsure about any steps, consult a qualified automotive technician.

Mounting

Secure the tachometer using the provided mounting bracket and pedestal. Choose a location that offers clear visibility to the driver without obstructing other controls or gauges. Ensure the mounting surface is stable and free from excessive vibration.

Wiring Connections

The tachometer requires connections for power, ground, and an ignition signal. Ensure all connections are secure and insulated to prevent short circuits.

  • Power: Connect to a switched 12V or 16V power source.
  • Ground: Connect to a reliable chassis ground point.
  • Ignition Signal: Connect to the vehicle's ignition system. This tachometer is compatible with 2-4 pulse ignition signals, suitable for 4-8 cylinder engines. It supports points, electronic, and most 12V high-performance racing ignitions.

Refer to your vehicle's service manual for specific ignition signal wire locations.

AUTO METER 233904 Autogage Monster Shift-Lite Tachometer with black dial and silver bezel

Front view of the AUTO METER 233904 Autogage Monster Shift-Lite Tachometer, showcasing the black dial, silver bezel, and the integrated shift light on the left side. The needle indicates approximately 6000 RPM.

Operating Instructions

Reading the Tachometer

The tachometer displays engine revolutions per minute (RPM) in thousands. The main dial is marked from 0 to 10, representing 0 to 10,000 RPM. The needle provides a quick and accurate indication of engine speed.

Shift Light Programming

The integrated shift light is user-programmable, allowing you to set a specific RPM threshold at which the light will illuminate. This feature helps in optimizing gear changes for peak performance.

  • To set the shift point, locate the small 'SHIFT-SET' button or adjustment screw on the tachometer face (typically near the 3 o'clock position).
  • With the engine running, or by simulating RPM, adjust the setting until the shift light illuminates at your desired RPM.
  • Test the setting to ensure it activates correctly during operation.
Side view of AUTO METER 233904 Tachometer showing shift light and mounting bracket

A slightly angled view of the tachometer, highlighting the adjustable shift light housing and the robust mounting bracket at the base. The 'SHIFT-SET' button is visible on the right side of the dial.

Maintenance

Cleaning

To clean the tachometer, use a soft, damp cloth. Avoid abrasive cleaners or solvents, as these can damage the finish or the clear lens.

Bulb Replacement

The tachometer uses traditional incandescent lighting. If the illumination dims or fails, the bulb may need replacement. Consult the manufacturer's specifications for the correct bulb type and replacement procedure.

Troubleshooting

If you encounter issues with your tachometer, review the following common problems and solutions:

  • No Power/No Illumination: Check power and ground connections. Verify the fuse in the power circuit. Ensure the incandescent bulb is functional.
  • Inaccurate RPM Reading: Confirm the ignition signal wire is correctly connected and receiving a clean signal. Ensure the tachometer is set for the correct number of engine cylinders (if adjustable).
  • Shift Light Not Functioning: Check the shift light bulb for continuity. Verify the shift point setting is correctly programmed and within the engine's operating range. Ensure all wiring to the shift light is secure.
  • Erratic Needle Movement: This can indicate a poor ground connection, interference from other electrical components, or an unstable ignition signal. Check all wiring and ensure proper shielding if necessary.

If problems persist after performing these checks, contact AUTO METER customer support.

Specifications

BrandAUTO METER
Model233904
MaterialMetal
Item Weight2.18 Pounds
UPC046074119088
ManufacturerAuto Meter
Bulb TypeIncandescent
Ignition Compatibility2-4 pulse ignition signals (4-8 cylinder engines)
Voltage Compatibility12 and 16 volt

Warranty and Support

For detailed warranty information, technical assistance, or to inquire about replacement parts, please visit the official AUTO METER website or contact their customer service department directly. Keep your purchase receipt for warranty claims.

Safety Information

CALIFORNIA WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.