Taylor Service Complete Pool Water Test Kit K-2006C User Manual

1. Introduction

The Taylor Service Complete Pool Water Test Kit K-2006C is designed for comprehensive analysis of pool and spa water. This kit provides accurate measurements for various parameters essential for maintaining water quality and safety. It is suitable for service technicians, commercial pool operators, and health department officials.

The kit utilizes 2 oz. reagents with titrants for enhanced accuracy and includes a printed color comparator, waterproof instructions, treatment charts, and a water chemistry guide.

2. Kit Components

The Taylor K-2006C test kit includes the following items:

• Convenient Storage Case
• 2000 Series Comparator
• Watergram® Water Balance Calculator
• Bottle with Dispenser Cap
• User Guide with Visual Step-by-Step Instructions
• Reagents (2 oz. bottles unless specified):
  • DPD Powder (10 grams x 2)
  • FAS-DPD Titrating Reagent
  • DPD Reagent #3
  • Phenol Red
  • Acid Demand Reagent
  • Base Demand Reagent
  • Cyanuric Acid Reagent (x2)
  • Sulfuric Acid .12N
  • Total Alkalinity Indicator
  • Thiosulfate N/10
  • Hardness Reagent
  • Calcium Indicator Liquid
  • Calcium Buffer
• Cyanuric Acid Testing Bottle (7 / 14 mL)

3. Setup and Preparation

Before performing any tests, ensure you have a clean, well-lit workspace. Read through the entire instruction manual provided with the kit to familiarize yourself with the procedures for each test.

1. Inspect Components: Verify all reagents and testing equipment are present and undamaged. Check reagent expiration dates.
2. Clean Equipment: Rinse all testing tubes and the comparator with the water to be tested before use. This prevents contamination from previous tests.
3. Sample Collection: Collect water samples from at least 18 inches below the surface of the pool or spa, away from return jets and skimmers.

4. Operating Instructions: Water Testing Procedures

The Taylor K-2006C kit allows for testing of Free & Total Chlorine, Bromine, pH, Acid Demand / Base Demand, Calcium Hardness, Total Alkalinity, and Cyanuric Acid. Always follow the specific instructions for each test as detailed in the kit's user guide.

General Testing Steps:

1. Step 1: Fill Comparator Cell
   Fill the comparator cell(s) or test tube(s) with the water sample to the indicated fill line.
2. Step 2: Add Reagent Drops
   Carefully add the specified number of drops of the appropriate reagent(s) for the test you are performing. Hold the reagent bottle vertically to ensure consistent drop size.
3. Step 3: Cap and Mix
   Cap the cell(s) or tube(s) and invert several times to thoroughly mix the reagents with the water sample.
4. Step 4: Compare Color
   Compare the resulting color of the water sample to the color standards on the comparator or color chart. Read the result that most closely matches the sample color. For titrimetric tests, count the drops until a specific color change occurs.

Parameters Measured:

• Free & Total Chlorine: Measures the amount of chlorine available for sanitization and combined chlorine. Range: 0.5ppm - 5.0ppm.
• Bromine: Measures bromine levels. Range: 1.0ppm - 10.0ppm.
• pH: Measures the acidity or alkalinity of the water. Range: 6.8 - 8.2.
• Acid Demand / Base Demand: Determines the amount of acid or base needed to adjust pH.
• Calcium Hardness: Measures the concentration of dissolved calcium.
• Total Alkalinity: Measures the water's ability to resist pH changes.
• Cyanuric Acid (Stabilizer): Measures stabilizer levels to protect chlorine from UV degradation.

Refer to the included Watergram® Water Balance Calculator and the detailed user guide for specific instructions on each test and interpreting results.

5. Maintenance and Storage

Proper maintenance and storage will extend the life and accuracy of your test kit.

• Cleanliness: Always rinse test cells and caps thoroughly with clean water after each use. Allow them to air dry before storing.
• Reagent Storage: Store reagents in a cool, dark place, away from direct sunlight and extreme temperatures. Ensure bottle caps are tightly sealed to prevent contamination or evaporation.
• Expiration Dates: Note the expiration dates on all reagent bottles. Expired reagents can lead to inaccurate test results and should be replaced.
• Kit Case: Keep the test kit components organized in the provided storage case to protect them from damage and light.

6. Troubleshooting

If you encounter issues with your test results, consider the following common troubleshooting steps:

• Inaccurate or Inconsistent Results:
  • Check reagent expiration dates.
  • Ensure proper sample collection technique (away from jets, sufficient depth).
  • Verify correct number of reagent drops and proper mixing.
  • Ensure test cells are clean and free from residue.
  • Avoid testing in direct sunlight, which can affect color comparisons.
• Difficulty Reading Color:
  • Use a white background when comparing colors.
  • Ensure adequate, consistent lighting.
  • If colors are too dark or light, consider diluting the sample (for some tests) or re-testing with fresh reagents.
• Reagent Contamination:
  • Always replace caps immediately after use.
  • Avoid touching the dropper tips to the water sample or other surfaces.

7. Specifications

8. Warranty and Support

Information regarding the specific warranty terms for the Taylor Service Complete Pool Water Test Kit K-2006C is not provided in the available product data. For warranty details or technical support, please refer to the documentation included with your purchase or contact Taylor Technologies directly through their official website.