Introduction
This manual provides essential information for the proper setup, operation, and maintenance of your Hamilton Baritone Sax Stand, Model KB570. Please read this manual thoroughly before using the product to ensure safe and efficient use.
Figure 1: Hamilton Baritone Sax Stand (Model KB570). This image shows the complete stand with its four-leg base, central pole, and the upper support cradle designed for a baritone saxophone bell.
Setup Instructions
Follow these steps to assemble your Hamilton Baritone Sax Stand:
- Unpack Components: Carefully remove all parts from the packaging. Verify that all components are present: the base with four legs and casters, the main vertical pole, and the upper saxophone support cradle.
- Attach Main Pole to Base: Insert the bottom end of the main vertical pole into the central receiver on the stand's base. Ensure it is fully seated and secure the locking mechanism, if present, by tightening the knob or screw.
- Install Saxophone Support Cradle: Slide the saxophone support cradle onto the top end of the main vertical pole. Position it so the bell ring is facing upwards and the back support is aligned. Tighten the adjustment screw to secure the cradle at the desired height and angle.
- Adjust Height and Angle: Loosen the height adjustment knob on the main pole to extend or retract the pole to the desired height. Tighten the knob firmly to lock the pole in place. Adjust the angle of the saxophone support cradle as needed for optimal instrument placement.
- Check Stability: Before placing your instrument on the stand, gently rock the stand to ensure it is stable and all connections are secure.
Operating Instructions
The Hamilton Baritone Sax Stand is designed for secure support and easy mobility of your baritone saxophone.
- Placing the Instrument: Carefully lift your baritone saxophone and place its bell into the support ring of the stand's cradle. Ensure the instrument is balanced and rests securely against the back support.
- Mobility: The stand is equipped with casters for easy movement. To move the stand, gently push or pull it to the desired location. Exercise caution when moving the stand with an instrument on it, especially over uneven surfaces.
- Storage: This stand is ideal for both storage and pedagogical use. When not in use, ensure the instrument is properly seated and the stand is placed in a stable, low-traffic area to prevent accidental tipping.
Maintenance
Regular maintenance will prolong the life and functionality of your stand.
- Cleaning: Wipe down the chrome plating with a soft, dry cloth to remove dust and fingerprints. For stubborn marks, a slightly damp cloth can be used, followed by immediate drying. Avoid abrasive cleaners.
- Caster Inspection: Periodically check the casters for any debris or hair that might impede their movement. Clean as necessary.
- Joints and Fasteners: Regularly inspect all screws, knobs, and joints to ensure they are tight. Re-tighten any loose fasteners to maintain stability. Do not overtighten.
- Protective Padding: Ensure the protective padding on the saxophone support cradle is intact and not worn. Worn padding can be replaced to prevent scratching your instrument.
Troubleshooting
This section addresses common issues you might encounter with your stand.
| Problem | Possible Cause | Solution |
|---|---|---|
| Stand feels unstable or wobbly. | Loose connections; uneven surface. | Ensure all knobs and screws are tightened securely. Move the stand to a flat, level surface. |
| Height adjustment slips. | Adjustment knob not tightened sufficiently; worn internal mechanism. | Tighten the height adjustment knob firmly. If slipping persists, inspect the internal friction mechanism for wear. |
| Casters do not roll smoothly. | Debris in casters; damaged casters. | Clean any debris from the caster wheels. If damaged, replacement casters may be required. |
Specifications
- Model: KB570
- Brand: HamiltonBuhl
- Item Weight: 2.5 pounds (1.13 kg)
- Product Dimensions: 19 x 14 x 19 inches (48.26 x 35.56 x 48.26 cm)
- Material: Durable chrome plating
- Features: Casters for easy movement, designed for baritone saxophone.
Warranty and Support
For warranty information or technical support regarding your Hamilton Baritone Sax Stand, please contact HamiltonBuhl customer service. Refer to your purchase documentation for specific warranty terms and contact details.
Online Resources: Visit the official HamiltonBuhl website for additional product information and support resources.
