1. Introduction
Thank you for choosing the Arrow Fastener ET200 Heavy Duty Electric Nail Gun. This manual provides essential information for the safe operation, maintenance, and troubleshooting of your new tool. Please read this manual thoroughly before using the nail gun to ensure proper function and to prevent injury.
2. Safety Instructions
WARNING: Failure to follow these safety instructions may result in serious injury or property damage.
- Always wear safety glasses to protect your eyes from flying debris.
- Keep hands and body parts away from the firing area.
- Ensure the workpiece is stable and secure before firing.
- Do not operate the tool if you are tired or under the influence of drugs, alcohol, or medication.
- Utilize the dual safety switches for operator protection. The tool is designed with both a trigger safety and a contact-fire safety switch.
- Disconnect the tool from the power source before performing any adjustments, clearing jams, or servicing.
- Keep children and bystanders away while operating a power tool.
- Use only genuine Arrow brad nails of the correct size for this tool.
3. Product Overview
The Arrow Fastener ET200 is an electric brad nailer designed for various fastening applications. Its ergonomic design reduces operator fatigue, and its tough, impact-resistant housing ensures durability.
Figure 1: The Arrow Fastener ET200 Electric Nail Gun, shown in its custom molded carrying case. This image highlights the tool's design and the types of brad nails it supports.
Key Features:
- Ergonomic design for reduced operator fatigue.
- Dual safety switches for operator protection.
- Long-lasting hardened steel moving parts.
- Tough, impact-resistant housing.
- Durable 10-foot power cord for extended reach.
- Shoots brad nail sizes: 5/8", 3/4", 1", and 1-1/4".
4. Setup
4.1 Loading Brad Nails
- Ensure the tool is unplugged from the power source.
- Locate the nail magazine release mechanism (refer to tool diagram if available).
- Open the nail magazine.
- Insert a strip of compatible brad nails (5/8", 3/4", 1", or 1-1/4") into the magazine with the points facing forward.
- Close the nail magazine securely until it latches.
4.2 Power Connection
- The ET200 is equipped with a durable 10-foot power cord.
- If an extension cord is required, it must be 12 gauge or higher. Using a smaller gauge extension cord will cause the tool to fire with less power and may damage the tool.
- Plug the tool into a standard electrical outlet.
5. Operating Instructions
5.1 Firing the Nail Gun
- Ensure the tool is loaded with brad nails and connected to power.
- Place the nose of the tool firmly against the workpiece where the nail is to be driven. The contact-fire safety switch must be depressed.
- Press the trigger to fire a nail.
- Release the trigger and lift the tool from the workpiece.
5.2 Recommended Usage
The ET200 is suitable for various applications, including:
- Crown moldings
- Cabinet drawers
- Door moldings
- Railings
- Wood trim and lattice work
- Furniture and cabinetry upholstery
- Paneling
5.3 Firing Rate
For optimal performance and tool longevity, observe the following:
- The tool can fire a maximum of 20 times per minute.
- It is recommended to wait at least 3 seconds between firings for the tool to work optimally and prevent overheating.
6. Maintenance
- Cleaning: Regularly clean the tool with a dry cloth. Do not use solvents or abrasive cleaners. Ensure the air vents are clear of dust and debris.
- Inspection: Periodically inspect the power cord for damage. Check the firing mechanism and safety switches for proper operation.
- Storage: Store the tool in its custom molded case in a dry, secure location, out of reach of children.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Tool does not fire |
|
|
| Nails not fully driven |
|
|
| Nail jam |
|
|
8. Specifications
| Brand | Arrow Fastener |
| Model Number | ET200D/ET200 |
| Compatible Brad Nail Sizes | 5/8", 3/4", 1", 1-1/4" |
| Power Source | Corded Electric |
| Cord Length | 10 feet |
| Item Dimensions (L x W x H) | 8 x 4 x 6 inches |
| Item Weight | 2 pounds |
| Material | Aluminum, Plastic |
| Special Features | Operator Protection, Durability, Impact Resistance, Extended Reach |
9. Warranty
The Arrow Fastener ET200 Electric Nail Gun comes with a manufacturer's warranty of 90 Days from Date of Purchase. Please retain your proof of purchase for warranty claims. This warranty covers defects in material and workmanship under normal use.
10. Support
For further assistance, technical support, or warranty inquiries, please contact Arrow Fastener customer service. Visit the official Arrow Fastener website for contact information and additional resources.