Introduction
The Bounty Hunter TK2 Tracker II Metal Detector is designed for efficient metal detection, offering advanced features and performance. It includes three distinct modes of operation and a 7-inch waterproof search coil, making it suitable for various environments. This detector combines the convenience of automatic ground balancing with manual settings, allowing for effective use in challenging soil conditions. It features four easy-to-use knob controls and full discrimination capabilities to help identify target metals.
Key Features
- 3 modes of operation for versatile detection.
- Automatic and manual ground balance for adaptability to different soil types.
- Sensitivity meter to gauge signal strength.
- Redesigned graphics and electronics for enhanced performance.
- Capable of sifting through challenging soil conditions.
- 2-tone audio feedback for target identification.
- Requires two 9-volt alkaline batteries (sold separately).
- Ships in Certified Frustration-Free Packaging.
Setup
Assembly
Carefully unpack all components of your Bounty Hunter TK2 Tracker II Metal Detector. The detector consists of a control housing, a stem, and a search coil. Attach the search coil to the lower stem using the provided bolt and wing nut, ensuring it is securely fastened but allows for slight angle adjustment. Connect the lower stem to the upper stem. Finally, attach the control housing to the upper stem and secure the armrest. Route the search coil cable neatly around the stem and plug it into the control housing, ensuring a snug connection.
Image: The Bounty Hunter TK2 Tracker II Metal Detector shown fully assembled, ready for use. It features a black control box with four knobs, a black stem, an armrest, and a round black search coil at the bottom.
Battery Installation
The Bounty Hunter TK2 Tracker II requires two 9-volt alkaline batteries for operation. To install the batteries, locate the battery compartment on the control housing. Open the compartment cover and insert the batteries, observing the correct polarity (+/-) as indicated inside the compartment. Close the cover securely. Ensure fresh batteries are used for optimal performance. Batteries are sold separately.
Operating Instructions
Control Panel Overview
The control panel of the Tracker II features four primary knobs for adjusting detector settings, along with a sensitivity meter for visual feedback.
Image: A close-up view of the Bounty Hunter TK2 Tracker II control panel. It displays four control knobs labeled 'Sensitivity', 'Mode', 'Discrimination', and 'Ground', along with a 'Sensitivity' meter on the right side.
- SENSITIVITY: Adjusts the detector's responsiveness to targets and ground minerals.
- MODE: Selects between different detection modes (All Metals, Tone, Discriminate).
- DISCRIMINATION: Filters out unwanted metals.
- GROUND: Adjusts the detector to compensate for ground mineralization.
Modes of Operation
The Tracker II offers three distinct operating modes:
- ALL METALS: Detects all types of metal objects. This mode offers the greatest depth detection.
- TONE: Provides different audio tones for various types of metals, aiding in target identification without visual inspection.
- DISCRIMINATE: Allows the user to filter out unwanted metals (e.g., iron, foil) and focus on more desirable targets.
Ground Balance
The detector features both automatic and manual ground balance capabilities. Automatic ground balance is suitable for most general detecting conditions. For highly mineralized soil, manual ground balance can be adjusted using the 'GROUND' knob to reduce false signals caused by ground minerals, improving detection accuracy and depth.
Sensitivity Adjustment
The 'SENSITIVITY' knob controls the detector's signal strength. Increasing sensitivity can lead to greater detection depth but may also increase susceptibility to electrical interference and ground noise. Decrease sensitivity if the detector is erratic or producing false signals.
Discrimination
Use the 'DISCRIMINATION' knob to eliminate unwanted metal signals. Turning the knob clockwise increases the level of discrimination, filtering out more types of junk metal. The 2-tone audio feedback system provides distinct sounds for different metal categories, assisting in distinguishing valuable targets from trash.
Maintenance
- Keep the detector clean by wiping it with a damp cloth after each use.
- The search coil is waterproof and can be rinsed with fresh water, but the control housing is not. Avoid submerging the control housing.
- Store the detector in a dry, cool place when not in use.
- Remove batteries if the detector will not be used for an extended period to prevent leakage.
- Avoid exposing the detector to extreme temperatures.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No power | Dead or incorrectly installed batteries. | Replace batteries with fresh 9-volt alkaline batteries, ensuring correct polarity. |
| Erratic beeping or false signals | High sensitivity, ground mineralization, or electrical interference. | Reduce 'SENSITIVITY'. Adjust 'GROUND' balance. Move away from power lines or other electronic devices. |
| Poor depth detection | Low sensitivity, high discrimination, or improper ground balance. | Increase 'SENSITIVITY'. Reduce 'DISCRIMINATION'. Re-adjust 'GROUND' balance. |
| No audio response | Headphones not connected properly or faulty. | Check headphone connection. Test with another pair of headphones. |
Specifications
| Feature | Detail |
|---|---|
| Brand | Bounty Hunter |
| Model Number | TK2-PL |
| Power Source | Battery Powered |
| Batteries Required | Yes (2 x 9-volt alkaline, sold separately) |
| Material | Metal |
| Item Weight | 1.77 pounds (0.8 kg) |
| Product Dimensions | 48 x 7 x 9 inches (121.9 x 17.8 x 22.9 cm) |
| Extended Length | 51 Inches (129.5 cm) |
| Adjustable Length | Yes |
| Search Coil Size | 7.75 Inches (19.7 cm) |
| Operating Frequency | 7 KHz |
| International Protection Rating | IP54 |
Warranty and Support
The manufacturer's warranty covers defects in materials and workmanship under normal use. Please note that the warranty does not cover misuse of the product. For specific warranty details, service, or technical support, please refer to the official Bounty Hunter website or contact their customer service department.
You can visit the official Bounty Hunter store for more information: Bounty Hunter Store