Introduction
This manual provides essential information for the setup, operation, and maintenance of your BIC America Venturi DV64 2-Way Tower Speaker. Designed for high-performance audio, this speaker can be used in traditional stereo setups or as a front speaker in a surround sound system. Please read these instructions carefully to ensure optimal performance and longevity of your speaker.
Setup
Unpacking
Carefully remove the speaker from its packaging. Retain all packaging materials for future transport or storage.
Placement
For optimal sound quality, place the DV64 speakers on a stable, level surface. Ensure adequate space around the speakers for proper ventilation and sound dispersion. If using in a stereo pair, position them equidistant from your primary listening position and spaced appropriately for a balanced soundstage. The speakers are magnetically shielded to prevent interference with televisions or monitors.
Figure 1: BIC America Venturi DV64 Tower Speaker showing its dimensions (38" H x 8.5" W x 9.25" D).
Connecting to an Amplifier
Connect the speaker to your amplifier or receiver using high-quality speaker wire. Ensure that the positive (+) terminal on the speaker is connected to the positive (+) terminal on the amplifier, and the negative (-) terminal on the speaker is connected to the negative (-) terminal on the amplifier. Incorrect polarity can result in poor sound quality.
The DV64 speaker is designed to work with amplifiers providing 10 to 200 watts of power. Do not exceed the maximum recommended amplifier power of 200 watts to prevent damage to the speaker.
Operating Instructions
Initial Playback
After connecting the speakers, select your audio source and begin playback at a low volume. Gradually increase the volume to a comfortable listening level. Allow a "break-in" period for the speakers, typically several hours of playback, for the drivers to fully settle and achieve their optimal sound characteristics.
Sound Adjustment
Adjust the bass and treble settings on your amplifier or receiver to suit your personal preference and room acoustics. The DV64 speakers are designed to deliver a balanced audio profile with impressive mid-tones and extended bass.
Maintenance
Cleaning
To clean the speaker cabinet, use a soft, dry cloth. For stubborn marks, a slightly damp cloth can be used, followed immediately by a dry cloth. Avoid using harsh chemicals, abrasive cleaners, or solvents, as these can damage the finish.
Grille Care
The speaker grilles can be removed for cleaning or for a different aesthetic. Gently pull the grilles away from the cabinet. Clean them with a soft brush or a lint roller to remove dust. Reattach by aligning the pins with the corresponding holes and pressing gently.
Figure 2: Front view of the BIC America Venturi DV64 speaker with the grille removed, revealing the Ferrofluid cooled tweeter, two 6.5-inch active woofers, and two 6.5-inch passive radiators.
Troubleshooting
- No Sound:
- Check all speaker wire connections at both the speaker and the amplifier. Ensure correct polarity (+ to + and - to -).
- Verify that the amplifier is powered on and the correct input source is selected.
- Confirm that the volume on the amplifier is not set to minimum or muted.
- Distorted Sound:
- Reduce the volume level on your amplifier. Overdriving the speakers can cause distortion.
- Check speaker wire connections for any loose strands or short circuits.
- Ensure the audio source is clean and not distorted.
- Lack of Bass:
- Verify speaker polarity. Incorrect wiring can cause bass cancellation.
- Check amplifier bass settings.
- Ensure speakers are not placed too close to walls or corners, which can sometimes over-emphasize or cancel bass frequencies depending on room acoustics.
Specifications
| Feature | Detail |
|---|---|
| Model Name | DV64 |
| Speaker Type | 2-Way Tower Speaker |
| Driver Configuration | One 0.75" Soft Dome Tweeter (Ferrofluid Cooled), Two 6.5" Poly/Graphite Active Woofers, Two 6.5" Passive Radiators |
| Frequency Response | 29 Hz - 21 kHz |
| Recommended Amplifier Power | 10 - 200 Watts |
| Maximum Output Power | 400 Watts |
| Sensitivity | 90dB @ 1W/1m |
| Impedance | 8 Ohms |
| Dimensions (H x W x D) | 38" x 8.5" x 9.25" |
| Item Weight | 34 pounds (15.4 kg) |
| Enclosure Material | Wood with Black Laminate Finish |
| Shielding | Magnetically Shielded |
Warranty Information
The BIC America Venturi DV64 speaker comes with a generous seven-year limited warranty on parts and labor. This warranty covers manufacturing defects and workmanship under normal use.
Important: The warranty does not cover misuse of the product. Please refer to the included warranty card for full terms and conditions.
Support
For further assistance, technical support, or warranty claims, please refer to the warranty card included with your product or visit the official BIC America website.
Official Website: www.bicamerica.com
