Technics ST-GT 350 Stereo Synthesizer Tuner User Manual

Introduction

Welcome to the user manual for your Technics ST-GT 350 Stereo Synthesizer Tuner. This manual provides detailed instructions to help you set up, operate, and maintain your tuner for optimal performance. Please read this manual thoroughly before using the unit and keep it for future reference.

Important Safety Information

To ensure safe operation and prevent damage, please observe the following precautions:

• Power Source: Ensure the unit is connected to an AC power source within the specified voltage range.
• Ventilation: Do not block ventilation openings. Allow adequate space around the unit for proper airflow.
• Water and Moisture: Do not expose the unit to rain, moisture, or excessive humidity.
• Heat Sources: Keep the unit away from heat sources such as radiators, heat registers, stoves, or other apparatus that produce heat.
• Cleaning: Unplug the unit from the wall outlet before cleaning. Use a dry cloth for cleaning.
• Servicing: Do not attempt to service this product yourself. Refer all servicing to qualified service personnel.

Package Contents

Please check that all the following items are included in the package:

• Technics ST-GT 350 Stereo Synthesizer Tuner Unit
• FM Indoor Antenna
• AM Loop Antenna
• AC Power Cord
• Audio Connection Cables (RCA type)
• User Manual (this document)

Product Overview

Front Panel

The front panel of the Technics ST-GT 350 features controls for power, band selection, memory functions, and tuning. The large display provides information on the selected station frequency and signal strength.

Figure 1: Front view of the Technics ST-GT 350 Tuner. This image shows the main controls including the power button, display, band selection, memory presets, and tuning knob.

Rear Panel

The rear panel provides all necessary connection ports for power, antennas, and audio output to your amplifier or receiver.

Figure 2: Rear view of the Technics ST-GT 350 Tuner. This image highlights the connection terminals for FM and AM antennas, audio output, and the AC power input.

Setup Guide

1. Connecting Antennas

• FM Antenna: Connect the supplied FM indoor antenna to the 75Ω FM ANT terminal. For better reception, connect an outdoor FM antenna.
• AM Antenna: Connect the supplied AM loop antenna to the AM ANT terminals. Position the loop antenna away from the main unit and other audio components to minimize interference.

2. Connecting to an Amplifier/Receiver

Use the supplied audio connection cables (RCA type) to connect the AUDIO OUT (L and R) terminals on the ST-GT 350 to the corresponding audio input terminals (e.g., "TUNER" or "AUX") on your amplifier or receiver.

3. Power Connection

After all other connections are made, plug the AC power cord into the AC INlet on the rear panel of the tuner, then plug the other end into a wall outlet.

Operating Instructions

1. Power On/Off

Press the POWER STANDBY/ON button on the front panel to turn the unit on or off.

2. Selecting a Band (FM/MW)

Press the BAND button to switch between FM and MW (AM) bands.

3. Tuning to a Station

Manual Tuning:

Press the MODE button until "MANUAL" appears on the display. Rotate the TUNING knob to manually adjust the frequency.

Automatic Tuning:

Press the MODE button until "AUTO" appears on the display. Press the TUNING knob (or the up/down arrows next to it, if present) to automatically scan for the next available station.

4. Presetting Stations (Memory)

The ST-GT 350 allows you to store up to 30 FM/MW stations in memory.

1. Tune to the desired station.
2. Press the MEMORY button. The preset number will flash on the display.
3. Within a few seconds, press one of the numbered preset buttons (1-10, or use the up/down arrows to select a higher number) to store the station.

5. Recalling Preset Stations

Press the desired numbered preset button (1-10) to instantly recall a stored station. For presets 11-30, you may need to press a "SHIFT" or "10+" button followed by the number, or use the up/down arrows to navigate through the memory banks.

Maintenance

Cleaning the Unit

To clean the exterior of the unit, wipe it with a soft, dry cloth. For stubborn dirt, dampen the cloth slightly with water or a mild, non-abrasive detergent. Never use strong solvents such as alcohol, paint thinner, or benzene, as these can damage the finish.

Storage

If you plan not to use the unit for an extended period, unplug it from the power outlet and store it in a cool, dry place, away from direct sunlight and extreme temperatures.

Troubleshooting

If you experience problems with your Technics ST-GT 350, please refer to the following table before seeking professional service.

Specifications

The following are the technical specifications for the Technics ST-GT 350 Stereo Synthesizer Tuner:

• Model: TECHNICS ST-GT 350
• Brand: Technics
• Manufacturer: Panasonic
• Special Features: Digital display
• Audio Output Mode: Stereo
• Audio Encoding: PCM
• Compatible Devices: PC, game console, TV, speaker, amplifier
• Item Weight: 10 g
• ASIN: B00008VIIQ
• First Available Date: January 15, 2020

Warranty and Support

For information regarding the warranty period and terms for your Technics ST-GT 350 tuner, please refer to the warranty card included with your product or contact your local Technics/Panasonic authorized dealer or service center. Keep your proof of purchase for warranty claims.

For technical support, troubleshooting beyond this manual, or service inquiries, please visit the official Technics or Panasonic support website or contact their customer service helpline in your region.