Introduction
The GBC HeatSeal H700 Pro is a professional thermal pouch laminator designed for high-quality lamination of documents and mounting boards. It supports materials up to 18 inches wide and accepts pouches ranging from 1.5 to 10 mil in thickness. This laminator features variable temperature and speed controls, along with a cooling fan, to ensure optimal laminating results. Its robust design makes it suitable for frequent use in various professional environments.
Image: The GBC HeatSeal H700 Pro laminator in operation, processing colorful documents. The machine is light-colored with a dark control panel on the right side.
Setup
- Unpacking: Carefully remove the laminator from its packaging. Ensure all packing materials are removed from the unit.
- Placement: Place the laminator on a stable, flat surface with adequate ventilation around the unit. Ensure the power cord can reach a suitable electrical outlet without strain.
- Power Connection: Plug the laminator into a grounded electrical outlet.
- Power On and Warm-up: Turn on the laminator using the power switch. The unit typically takes 4 to 8 minutes to warm up. A "ready" light or indicator on the LCD display will signal when the machine has reached the optimal operating temperature.
- Setting Temperature and Speed: Use the one-touch keypad with LCD display to set the desired temperature and speed. The laminator offers variable temperature and speed control to accommodate different pouch thicknesses and material types. For general use, a speed of 3 and a temperature of 285°F are often recommended, but adjust as needed for your specific laminating pouches and documents.
Image: An overhead view of the GBC HeatSeal H700 Pro laminator, illustrating its key features: up to 10 mil pouch thickness, temperature and speed controls, 4-8 minute warm-up time, and an 18-inch laminating width.
Operating Instructions
- Prepare Document: Place your document or mounting board inside a thermal laminating pouch. Ensure the document is centered and there is a small margin around the edges.
- Insert Pouch: Once the laminator is warmed up and set to the correct temperature and speed, carefully feed the sealed edge of the laminating pouch into the laminator's entry slot. The machine's rollers will automatically pull the pouch through.
- Lamination Process: Allow the laminator to complete the process. The four rollers are designed to provide bubble-free results.
- Cooling: After the pouch exits the laminator, place it on a flat surface to cool and harden.
- Cold Lamination: For pressure-sensitive pouches, utilize the cold setting available on the control panel for smooth lamination results without heat.
Image: A close-up view of the GBC HeatSeal H700 Pro laminator's feed slot, showing a thick, colorful board being laminated. This highlights the machine's capability to handle various materials.
Image: A detailed view of the GBC HeatSeal H700 Pro laminator's control panel, featuring an LCD display and various buttons for temperature, motor/speed, carrier, direct, pre-heat, mount, cold, F/C (Fahrenheit/Celsius), stop, and reverse functions.
Maintenance
- Cleaning: Regularly wipe the exterior of the laminator with a soft, dry cloth. For stubborn marks, a slightly damp cloth can be used, ensuring no liquid enters the machine.
- Roller Care: Periodically clean the laminator rollers to prevent adhesive buildup, which can affect lamination quality. Refer to the full user manual for specific roller cleaning instructions.
- Storage: When not in use, store the laminator in a clean, dry environment away from direct sunlight and extreme temperatures.
Troubleshooting
- Pouch Jams: If a pouch becomes jammed, immediately press the "Reverse" button on the control panel to attempt to clear the jam. If the jam persists, power off the machine and carefully remove the pouch.
- Poor Lamination Quality:
- Bubbles/Wrinkles: Adjust the temperature setting. Too low a temperature can cause bubbles, while too high can cause wrinkles. Ensure the pouch is fed straight.
- Cloudiness: Increase the temperature setting slightly.
- Unsealed Edges: Ensure the correct pouch thickness is being used for the chosen temperature.
- Machine Not Heating: Verify the power cord is securely plugged in and the power switch is on. If the issue persists, contact customer support.
Specifications
| Feature | Detail |
|---|---|
| Brand | GBC |
| Model Number | GBC1700500 |
| Max Laminating Width | 18 inches |
| Pouch Thickness Compatibility | 1.5 to 10 mil |
| Warm-up Time | 4-8 minutes |
| Lamination Speed | Up to 60 inches per minute |
| Dimensions (L x W x H) | 18.13 x 31.75 x 11.88 inches |
| Item Weight | 1 pound |
| Material Type | Metal |
| Color | Silver |
Warranty and Support
For detailed warranty information and customer support, please refer to the official GBC website or the full user manual. Protection plans, such as a 4-Year Protection Plan or a Complete Protect plan, may be available for purchase to extend coverage for your laminator.
A comprehensive User Manual in PDF format is available for download: Download User Manual (PDF)
