1. Product Overview
The Schneider Electric QO200TRCP is a 60 Amp non-fusible AC disconnect switch designed for safely disconnecting power to specific loads, such as outdoor air conditioning units. This device provides a reliable, quick-make, quick-break operating mechanism for enhanced safety and ease of use. It is suitable for residential and commercial applications and is UL Listed, ensuring compliance with safety standards.
Important Note: This disconnect switch does not provide overcurrent protection. Overcurrent protection must be provided by a fuse or circuit breaker rated 60 amps or less in the main electrical panel.
2. Safety Information
WARNING: Risk of Electric Shock, Explosion, or Arc Flash.
- This equipment must be installed and serviced by qualified electrical personnel only.
- Always use a properly rated voltage sensing device to confirm power is OFF.
- Turn off all power supplying this switch before working on or inside the equipment.
- Do not use this switch for overcurrent protection.
- Failure to follow these instructions will result in death or serious injury.
3. Product Features
- 60A Non-Fusible Disconnect
- Rainproof, Double Pole with Ground Bar (NEMA Type 3R for outdoor use)
- 240V AC Operating Voltage
- UL Listed for safety and compliance
- Enclosed molded case switch
- Water resistant/rainproof design
- Compact design for use with 75-degree Celsius wire
- Advanced design with reliable, quick-make, quick-break operating mechanism
4. Setup and Installation
Installation of this electrical disconnect switch should only be performed by qualified electrical personnel in accordance with all national and local electrical codes.
4.1 Pre-Installation Checks
- Verify that the power supply is completely disconnected at the main breaker panel before beginning any work.
- Ensure the voltage and amperage ratings of the disconnect switch match the requirements of the connected load (e.g., AC unit).
- Confirm the enclosure type (NEMA Type 3R) is appropriate for the installation environment (outdoor, rainproof).
4.2 Mounting the Disconnect Switch
Mount the QO200TRCP securely to a flat, stable surface near the equipment it will disconnect. Ensure adequate clearance for wiring and operation of the handle.
Image: The Square D QO200TRCP 60 Amp Non-Fusible AC Disconnect Switch, shown in its gray, enclosed housing with the operating handle visible on the side. This unit is designed for outdoor use.
4.3 Wiring Connections
- Open the enclosure cover.
- Connect the incoming power supply wires to the line terminals.
- Connect the load wires (to the AC unit or other equipment) to the load terminals.
- Connect the ground wire to the integrated ground bar. The ground bar is bonded to the back of the enclosure.
- Ensure all connections are tight and secure.
- Close and secure the enclosure cover.
4.4 Installation Video Overview
Video: An overview of the Square D by Schneider Electric QO200TRCP 60 Amp Non-Fusible AC Disconnect Switch, highlighting its features and typical installation context. This video provides visual guidance on the product's design and application.
5. Operating Instructions
The QO200TRCP disconnect switch features a simple ON/OFF operating mechanism.
- To turn power ON: Move the operating handle to the 'ON' position.
- To turn power OFF: Move the operating handle to the 'OFF' position.
Always ensure the handle is fully engaged in either the ON or OFF position.
6. Maintenance
Regular maintenance helps ensure the longevity and safe operation of your disconnect switch. All maintenance should be performed by qualified personnel with power disconnected.
- Periodic Inspection: Annually inspect the enclosure for any signs of damage, corrosion, or loose connections.
- Cleaning: Keep the exterior of the enclosure clean and free from debris. Do not use abrasive cleaners.
- Terminal Check: Periodically check terminal screws for tightness, especially after initial installation and during routine electrical system checks.
7. Troubleshooting
If you experience issues with your QO200TRCP disconnect switch, consider the following common troubleshooting steps. Always ensure power is OFF before inspecting the unit.
- No Power to Load: Verify the disconnect switch handle is fully in the 'ON' position. Check the main circuit breaker or fuse in the electrical panel to ensure it has not tripped or blown.
- Loose Connections: With power OFF, carefully inspect all wiring connections within the enclosure for tightness.
- Physical Damage: Inspect the switch and enclosure for any visible signs of damage. If damage is found, the unit may need replacement.
For persistent issues or complex problems, contact a qualified electrician or Schneider Electric customer support.
8. Specifications
| Specification | Value |
|---|---|
| Model Number | QO200TRCP |
| Current Rating | 60 Amps |
| Operating Voltage | 240 Volts AC |
| Poles | 2 Pole |
| Wires | 2 Wire |
| Horsepower Rating | 10 HP |
| Enclosure Type | NEMA Type 3R (Rainproof) |
| Fusible/Non-Fusible | Non-Fusible |
| Contact Type | Normally Open |
| Connector Type | Screw |
| Terminal | Screw |
| Dimensions (L x W x H) | 3.88 x 4.63 x 6.5 inches |
| Item Weight | 2.2 pounds |
| Color | Gray |
| UL Listed | Yes |
9. Warranty and Support
For information regarding product warranty, please refer to the official Schneider Electric website or contact their customer support directly. Schneider Electric is committed to providing reliable products and excellent customer service.
Schneider Electric Customer Support:
- Visit the Schneider Electric Store on Amazon for product information.
- Refer to the official Schneider Electric website for comprehensive support resources and contact details.
