Introduction
Thank you for choosing the Altec Lansing ACS33 PowerCube Computer Speaker System. This 3-piece audio system is designed to provide high-quality sound for your computer, enhancing your audio experience with its compact satellite speakers and powerful subwoofer. This manual provides essential information for setting up, operating, and maintaining your speaker system.
The ACS33 system features two compact, magnetically shielded satellite speakers and a powered subwoofer. It includes convenient volume control and a power-on LED indicator for ease of use.
Image: The Altec Lansing ACS33 PowerCube 3-piece computer speaker system, showing the subwoofer and two satellite speakers.
Package Contents
Please verify that all components are present in your package:
- Two (2) Satellite Speakers
- One (1) Powered Subwoofer
- Integrated Cables for connection
- User Instructions (this manual)
_image_3.jpeg)
Image: Top view of the Altec Lansing ACS33 PowerCube system, displaying the subwoofer and two satellite speakers with their connecting cables.
Setup Instructions
Follow these steps to correctly set up your Altec Lansing ACS33 speaker system:
- Placement: Position the subwoofer on the floor near your computer. Place the two satellite speakers on either side of your computer monitor, ensuring they are equidistant from your listening position for optimal stereo imaging. The satellite speakers are magnetically shielded to prevent interference with your monitor.
- Connect Satellite Speakers: Connect the cables from the two satellite speakers to the corresponding speaker output jacks on the back of the subwoofer. Ensure a secure connection.
- Connect to Audio Source: Connect the audio input cable from the subwoofer to the audio output jack (typically green) on your computer's sound card.
- Power Connection: Plug the subwoofer's power cord into a standard AC wall outlet.
_image_1.jpeg)
Image: Rear view of the Altec Lansing ACS33 subwoofer, showing the input and output connections for the satellite speakers and the power input.
Operating Instructions
Once the system is set up, follow these steps to operate your speakers:
- Power On: Locate the power/volume control knob on one of the satellite speakers. Turn the knob clockwise until you hear a click and the power-on LED illuminates.
- Adjust Volume: Continue turning the power/volume control knob clockwise to increase the volume. Turn it counter-clockwise to decrease the volume.
- Audio Playback: Start playing audio from your computer. Adjust the volume to your desired listening level.
- Power Off: To turn off the system, turn the power/volume control knob counter-clockwise until you hear a click and the power-on LED extinguishes.
Maintenance
Proper care will ensure the longevity and performance of your speaker system:
- Cleaning: Use a soft, dry cloth to clean the speaker surfaces. Do not use liquid cleaners or abrasive materials, as they may damage the finish or internal components.
- Ventilation: Ensure that the subwoofer and satellite speakers have adequate ventilation. Do not block any vents, especially on the subwoofer, to prevent overheating.
- Environment: Avoid placing the speakers in direct sunlight, near heat sources, or in areas with high humidity or excessive dust.
- Cable Management: Keep cables tidy and free from kinks or excessive bending to prevent damage.
Troubleshooting
If you encounter issues with your ACS33 speaker system, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| No sound | Speakers not powered on; volume too low; incorrect audio connection; computer audio settings. | Ensure power is on and LED is lit. Increase volume. Check all cable connections. Verify computer's audio output is set to the correct device. |
| Distorted sound | Volume too high; poor audio source quality; loose connection. | Reduce volume. Test with a different audio source. Check all cable connections for tightness. |
| Only one satellite speaker works | Loose connection to subwoofer; computer's balance settings. | Check the connection of the non-working satellite speaker to the subwoofer. Verify computer's audio balance settings. |
| Humming or buzzing noise | Ground loop interference; proximity to other electronic devices. | Try plugging the speakers into a different electrical outlet. Move speakers away from other electronics. |
If the problem persists after trying these solutions, please contact customer support.
Specifications
| Feature | Detail |
|---|---|
| Model Name | ACS33 |
| Speaker Type | Indoor, 3-piece system |
| Satellite Power | 10 Watts (per satellite) |
| Subwoofer Power | 15 Watts |
| Total Speaker Maximum Output Power | 35 Watts |
| Frequency Response | 70Hz - 18kHz |
| Signal-to-Noise Ratio (S/N) | >65dB |
| Satellite Driver | One 3 inch full range driver (per satellite) |
| Subwoofer Driver | One 4 inch long-throw woofer |
| Input Impedance | >10k ohms |
| Connectivity Technology | Wired |
| Power Source | AC (Built-in power supply) |
| Product Dimensions (Subwoofer) | 17.6"D x 11.7"W x 8.6"H (approximate) |
| Item Weight | 10.85 pounds |
| UPC | 021986940333 |
Warranty Information
The Altec Lansing ACS33 PowerCube Computer Speaker System comes with a Limited Warranty. Please refer to the warranty card included with your product for specific terms, conditions, and duration of coverage. Keep your proof of purchase for warranty claims.
Customer Support
For technical assistance or customer service inquiries, please contact Altec Lansing support:
- Phone: 800-ALTEC-88
- Website: www.altecmm.com
Please have your product model number (ACS33) and purchase information ready when contacting support.
