ASAFEE DC-01 Multi-function EDC Flashlight
Overview
Asafee® Ultra thin EDC flashlight is a compact aluminum alloy flashlight with LED + COB lighting, multiple light modes, and Type‑C charging. Use the switch to select modes and keep the battery and contacts properly installed for reliable operation.
Specifications
| Light source | LED + COB |
|---|---|
| Lighting modes | 7 light modes |
| Runtime | 2–8H |
| Lumens | 2400 LM |
| Charging port | Type‑C charging |
| Switch | Press switch |
| Size | Length 14 × Tail 3.6 × 15 cm |
| Battery | Built-in 1500 mAh battery (polymer) |
| Weight | 109 g |
| Material | Aluminum alloy |
| Waterproof rating | IPX4 |
| Package contents | Work lamp; Type‑C cable |
Quick Guide
- Charge the flashlight using the Type‑C charging port. Battery capacity is 1500 mAh; charging time is 4 hours (first charge: at least 6 hours).
- Remove any battery insulation sheet before use (if present).
- Install/confirm the battery direction is correct and the switch/tail cover are properly tightened for good contact.
- Press the switch to turn on and cycle through the 7 light modes as listed in the manual (S1 and S2 sequences).
- For use, ensure heat dissipation; when fully charged, it is recommended to start with the second gear first.
Features
PRODUCT STRUCTURE
PRODUCT SPECIFICATION
| Specification | Detail |
|---|---|
| Light Source | LED+COB |
| Lighting mode | 7 light modes |
| Runtime | 2-8H |
| Lumens | 2400LM |
| Charging Port | TYPE-C charging |
| Switch | Press switch |
| Size | Length:14 * Tail:3.6 * 15CM |
| Battery Model | Built-in 1500mAh battery |
| Weight | 109G |
| Material | Aluminum alloy |
| Waterproof rating | IPX4 |
| Package Contents | ●Work lamp ●Type-c cable |
PRODUCT LIGHT MODE
- S1: Headlight Strong Light – Headlight Weak Light – Headlight Flash
- S2: COB strong light metering – COB weak light metering – Measurement of COB Red Light – Measurement of COB Red Flash
TYPE-C CHARGING
Built-in 1500mAh polymer battery Battery life: 2-8 hours, charging time: 4 hours Digital power display
WARM TIPS
- Instructions for Use of Lithium Batteries
- Features of lithium batteries: The charging method of lithium batteries is completely different from that of mobile phone batteries; lithium batteries have no memory and can be charged at any time. Do not overcharge or over-discharge.
- The first charge takes at least 6 hours. After that, just turn on the green light on the charger. There is no need to overcharge.
- Special reminder to use a “three-proof” charger that is anti-overcharge, anti-reverse connection, and anti-short circuit.
- If the battery is not used for a long time, it should be fully charged and stored. Normally, it should be charged and discharged once every three months.
- Instructions for Use of Flashlights
- When using a flashlight, choose it according to the flashlight’s requirements for voltage and battery. Do not use it indiscriminately to prevent the circuit board from being burned. Batteries of different models and voltages should not be used at the same time.
- During use, turn off the flashlight when the brightness of the flashlight changes significantly to prevent over-discharge of the battery.
- Heat dissipation tips: During the use of the flashlight, heat dissipation must be ensured. It is strongly recommended that when fully charged, it is best to use the second gear first, so that the flashlight head and battery can extend the product life!
- Do not shine the flashlight light directly into people’s eyes, as the light is extremely bright and dazzling, which can affect vision, especially for children.
- Fault troubleshooting
- Check the battery: Make sure the battery is charged and install the battery in the correct direction. Do not use batteries of different brands, and do not mix new and old batteries.
- Check the tail cover: Make sure the switch is tightened and in good contact. Ensure that the tail cover copper column and the tail cover pressure ring metal sheet are in good contact, and check whether the lamp head is loose.
- Check whether the battery insulation sheet has been removed before use.
Fault Troubleshooting
- Check the battery: Confirm the battery is charged and installed in the correct direction. Do not mix different brands or mix new and old batteries.
- Check the tail cover and contacts: Make sure the switch is tightened and in good contact. Ensure the tail cover copper column and tail cover pressure ring metal sheet are in good contact, and check whether the lamp head is loose.
- Check for insulation sheet: Verify the battery insulation sheet has been removed before use.
Documents / Resources
 | DC-01 Multi-function EDC Flashlight |
References
- User Manualmanual.tools
Published: August 29, 2026
Updated: August 30, 2026