ARTOME FR602 Remote Controller User Guide

ARTOME FR602 Remote Controller

OVERVIEW

Basic Operations

Introduction

The Artome unit can be conveniently controlled using a remote controller. This remote communicates with the Artome unit via Bluetooth. Only one remote controller can be connected to an Artome device at a time. The remote controller should not be replaced unless it is lost or damaged. The remote controller is already paired with the Artome unit at the factory, so the user does not need to pair it again.

Common Issues and Solutions

Note: If the Artome unit has been updated or reset to factory settings, the remote controller may need to be paired again. Follow the initial pairing instructions to perform the pairing. If this does not resolve the issue, contact customer support.

Initial Pairing Instructions (After factory reset)

Set Artome unit in Pairing Mode:

Press and hold the Pause button on the Artome unit for 2.5 seconds. The Pause LED will flash, indicating that the Artome is in pairing mode and ready to listen for advertising remote controllers.

Set the Remote Controller in Pairing Mode:

Press and hold both the Audio Only and AV Mute buttons on the remote controller simultaneously for about 5 seconds. Once the remote controller is connected to the Artome, the Volume + and Volume – LEDs on the Artome unit will illuminate for 2 seconds.

Battery Replacement Instructions

To ensure your Artome remote controller functions correctly, you may need to replace the batteries periodically. Follow the steps below to replace the batteries.

• Locate the Button to Open the Remote
  • On the backside of the remote (image A), find the button and press it firmly to release the back cover of the remote. Once the button is pressed, slide the back cover down to expose the battery compartment.
• Remove Old Batteries and Insert New Batteries
  • Take out the old AAA batteries from the battery compartment. Insert two new AAA batteries, ensuring that the positive (+) and negative (-) ends are aligned correctly as indicated in the image B.
• Replace the Back Cover
  • Slide the back cover back into place until it clicks securely.
• Test the Remote
  • Press any button on the remote to ensure it is working correctly.

Specifications

FCC

FCC Compliance

• Unique identifiers: FR602
• FCC ID:2BNPQ-FR602
• Responsible Party:
• Street address:31101 Wiegman road  Hayward CA 94544
• Tel. (619) 436 9131
• contact@artomeusa.com

FCC Caution：

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

CONTACT INFORMATION

Artome support

• support@artomeusa.com
• support@artome.fi

FAQs

• Q: What should I do if my remote controller is not working?
  • A: Ensure batteries are inserted correctly and have sufficient charge. Check if the Artome unit is powered and functional. If needed, try re-pairing the remote following the provided instructions.
• Q: How many batteries does the remote controller require?
  • A: The remote controller requires 2 AAA batteries for operation. Ensure correct alignment of the battery ends during replacement.