ARROW IDLX-35563 Pressure Injectable Three Lumen
Product Specifications
- Model: PB-10000-850
- Size: 8.5 X 10.5
- Catheter Length: 55 cm
- Spring-Wire Guide Diameter: .018 inch
- Lumen Sizes: Pink (17 Ga..), Blue (118 G), White (18 Ga.)
- Priming Volume (mL): 0.70 (Pink), 0.52 (Blue), 0.54 (White)
- Gravity Flow Rate (mL/hr): 940 (Pink), 340 (Blue), 340 (White)
- Pump Flow Rate (mL/hr): 5500 (Pink), 2660 (Blue), 2720 (White)
- Maximum Pressure Injection Flow Rate (mL/sec): 6 (Pink), Not rated (Blue), Not rated (White)
Preparation:
Ensure the area of insertion is clean and sterile.
Insertion Process:
- a. Insert the GlideThruTM Peel-Away Sheath followed by the Spring-Wire Guide into the designated area.
- b. Use the provided dilator to expand the entry point.
Catheter Placement:
- a. Carefully advance the catheter to the desired location.
- b. Confirm proper placement using imaging techniques if necessary.
Priming and Flow Rates:
- a. Prime the catheter with the appropriate volume based on the lumen size.
- b. Adjust the flow rate based on gravity or pump settings according to the required infusion rate.
Post-Procedure Care:
- a. Secure the catheter in place to prevent movement.
- b. Monitor the patient for any signs of complications or infections.
Contents:
- 1: Three Lumen TaperFree® Catheter‡‡‡: 6 Fr. (2.14 mm OD) x 55 cm, Pressure Injectable, Arrow® NaviCurve™ Stylet and T-Port Connector
- 1: GlideThru™ Peel-Away Sheath: 6 Fr. x 2-3/4″ (7 cm) Radiopaque over 6 Fr. Dilator
- 1: Spring-Wire Guide, Nitinol, Marked: .018″ (0.46 mm) dia. x 17-3/4″ (45 cm)
(Straight Soft Tip on One End – Straight Stiff Tip on Other) With Arrow Advancer - 1: Introducer Needle: 21 Ga. x 1-1/2″ (3.81 cm) TW
- 1: Injection Needle: Eclipse™1 25 Ga. x 1″ (2.54 cm)
- 1: Safety Introducer Needle: Echogenic 21 Ga. x 2-3/4″ (7 cm) TW
- 1: Introducer Needle: Echogenic 21 Ga. x 2-3/4″ (7 cm) TW
- 1: Filter Needle: 18 Ga. TW x 1-1/2″ (3.81 cm) with Blunt Fill Tip
- 1: Syringe: 10 mL Luer-Lock
- 1: Syringe: 3 mL Luer-Lock
- 3: Dust Cap: Non-Vented
- 1: SecondSite™ Adjustable Hub: Fastener
- 1: SecondSite™ Adjustable Hub: Catheter Clamp
- 1: SharpsAway® Disposal Cup
- 1: SharpsAway® II Locking Disposal Cup
- 1: Catheter Trimmer
- 1: Towel: 24″ x 36″ (61 cm x 91 cm)
- 1: Maximal Barrier Drape™ with two 13 cm (5″) x 15 cm (6″) fenestrations
- 1: Towel
- 1: Safety Scalpel: #11
- 1: Sterile Procedure Sign
- 1: Patient ID Card
- 1: Patient Information Booklet
- 2: Paper Tape Measure
- 1: Tourniquet
- 1: Foam Electrodes (3 per pack)
- 5: Gauze Pad: 2″ x 2″ (5 cm x 5 cm)
- 10: Gauze Pad: 4″ x 4″ (10 cm x 10 cm)
- 1: Surgical Apparel: Impervious Gown
- 1: Dressing: I.V. Advanced 8.5 cm x 11.5 cm
- 1: Transducer Cover with Gel and Rubber Bands
- 1: Remote Cover
- 1: Surgical Apparel: Mask with Eye Shield
- 1: Dressing: STATLOCK®2 PICC Plus Catheter Stabilization Device
- 1: Surgical Apparel: Bouffant Cap
- 1: Surgical Apparel: Mask
- 1: Tape: Steri-Strip®3
- 3: Valve: MicroCLAVE™4 Neutral Displacement Connector
- 1: T-Piece Cover
- 1A trademark of Becton, Dickinson and Company.
- 2A registered trademark of C. R. Bard, Inc.
- 3A registered trademark of 3M Company.
- 4A trademark of ICU Medical, Inc.
MR Safe
Not made with natural rubber latex. Contraindications: The Pressure Injectable PICC is contraindicated wherever there is the presence of device-related infections or the presence of thrombosis in the intended insertion vessel or catheter pathway. Clinical assessment of the patient must be completed to ensure no contraindications exist.
- Priming volumes are approximate and are done without accessories.
- Flow rate values are approximate and are determined using deionized water at 100 cm head height.
- Pump flow rates are determined at a maximum pump pressure of 10 psig and represent approximate flow capabilities.
- Pressure injection flow rates are determined at the injector pressure setting of 300 psi maximum using media of 11.8 centipoise viscosity, with 152 cm pressure tubing.
Frequently Asked Questions
Q: Is the product compatible with all types of infusion pumps?
A: The product is designed to work with most standard infusion pumps. However, always refer to the pump specifications or consult with a healthcare provider for compatibility confirmation.
Q: How often should the catheter be replaced?
A: The replacement frequency of the catheter depends on various factors including patient condition, usage duration, and clinical assessment. It is recommended to follow healthcare provider guidance on catheter replacement intervals.
Q: Can the catheter be used for contrast media injections?
A: The maximum pressure injection flow rates provided are suitable for certain contrast media injections. Always consult with a healthcare professional for specific guidance on contrast media injection procedures using this catheter.
Documents / Resources
 |
ARROW IDLX-35563 Pressure Injectable Three Lumen [pdf] Owner's Manual IDLX-35563-CURV, IDLX-35563 Pressure Injectable Three Lumen, Pressure Injectable Three Lumen, Injectable Three Lumen, Three Lumen |