ArmorPoxy ARM707X-RM 100% Solid With Metal Mixer and Bucket Instructions

Previously coated surfaces must be sound and in good condition.
Smooth, hard, or glossy finishes should be scarified by sanding or
sweep blasting to create a surface profile. ARM707X-RM 100% Solids
Epoxy Coating is compatible with most coatings, but a test patch is
suggested. Concrete must be visibly dry at the time of
application.

Mixing Equipment

Use a low-speed drill and spiral mixing wand for mixing. Hand
mixing is not recommended as it may lead to inconsistent results.
For 1.5 & 3 gallon kits, both A and B components are packaged
together for easy mixing. Use a narrow spiral paint mixer to premix
individual components within the kits.

Application Equipment

12 or larger notched or flat squeegee
3, 9, 18 short nap lint-free roller (1/4 or 3/8 roller)

Application

Apply the epoxy coating using the recommended squeegee and
roller. Follow the application instructions provided with the
product for best results.

Clean Up

Clean tools and application equipment immediately after use with
an active solvent like xylene (in SCAQMD use acetone only). Clean
spills or drips while still wet with solvent. Dried product will
require mechanical abrasion for removal.

Limitations

Read the notice to buyer regarding the disclaimer of warranties
and limitations on liability before using the product.

Frequently Asked Questions (FAQ)

Q: Can ARM707X-RM Epoxy Coating be applied on all
surfaces?

A: ARM707X-RM is compatible with most coatings, but it is
recommended to do a test patch on previously coated surfaces to
ensure compatibility.

Q: What should be used for cleaning up after application?

A: Clean tools and equipment immediately after use with an
active solvent like xylene. Spills or drips should be cleaned while
still wet with solvent.

Q: Can hand mixing be used for preparing the epoxy
coating?

A: Hand mixing is not recommended as it may result in
inconsistent mixing. Use a low-speed drill and spiral mixing wand
for proper mixing.

“`

View Fullscreen

INSTRUCTIONS
ARM707X-RM 100% SOLIDS EPOXY COATING

ArmorPoxy Inc. 860 Springfield Rd
Union, NJ 07083 armorpoxy.com E: support@armorpoxy.com P: 888-755-7361

PLEASE READ INSTRUCTIONS THOROUGHLY BEFORE APPLICATION BEGINS. FAILURE TO DO SO CAN RESULT IN PRODUCT FAILURE.

PRODUCT PREPARATION
NEW CONCRETE: Laitance must be removed by diamond for a minimum of 28 days. The concrete must be structurally sound, dry, and free of grease, oils, dust, curing compounds and other coatings or contaminants. Surface laitance must be removed. Rising moisture vapor emission rate must not exceed 3 lb. per 1000 sq. ft. over a 24 hour period as measured by calcium chloride test method ASTM F-1869. The preferred method of surface preparation is muriatic acid etching or to mechanically abrade the floor by diamond grinding to achieve a final 80120 grit finish, reference profile CSP-2 according to ICRI. If patching is required, use Fortification Formula concrete repair.
PREVIOUSLY COATED: Previously coated surfaces must be sound and in good condition. Smooth, hard, or glossy finishes should be scarified by sanding or sweep blasting to create a surface profile. ARM707X-RM 100% Solids Epoxy Coating is compatible with most coatings, but a test patch is suggested.
NOTE: Concrete must be visibly dry at time of application.

MIXING EQUIPMENT
Low speed drill and spiral mixing wand. Must pre-mix prior to use. Important: Hand mixing will produce inconsistent results and is not an approved method. Note: 1.5 & 3 gallon kits are packaged in an All-In-One packaging. Both A and B components are shipped together inside an outer pail that can be used for combining both components at the application site. For best results use narrow spiral paint mixer to premix individual components within the 1.5 and 3 gallon kits.

MIXING
Note: Before starting, ensure that the material, concrete surface, and the ambient air are all at 50-90°F. Mixing ratio is 2 parts by volume of Part A to 1 part by volume of part B. Pre-mix both A and B sides prior to combining. Add part “A” to the mixing container. Add part “B” to the mixing container and mix for 3 minutes.

APPLICATION EQUIPMENT
12″ or larger notched or flat squeegee 3″, 9″, 18″ short nap lint free roller (1/4″ or 3/8″ roller)

APPLICATION
Mix only what you can squeegee and back roll within 15-20 minutes (approximately 1 gallon of mixed material per crew of two applicators wearing spiked shoes). Do not aerate the mix. Before starting, ensure that the material, concrete surface, and the ambient air are all at 50-90°F. Do not apply in direct sunlight or when temperature is rising. Wearing spiked shoes, immediately pour mixed ARM707X-RM 100% Solids Epoxy Coating on the floor in ribbons. Spread using a squeegee and then back roll using a short nap lint-free roller. If priming is required, ARM707X-RM 100% Solids Epoxy Coating can be thinned up to 10% by volume with xylene and squeegeed tight to help fill small voids. Refer to recoat window below for best practice when abrading and/or applying subsequent coats.

CLEAN UP
Clean Tools and application equipment immediately after use with active solvent like xylene (in SCAQMD use acetone only). Clean spills or drips while still wet with solvent. Dried product will require mechanical abrasion for removal.

LIMITATIONS
Do not apply if water or ice is present. Lower temperatures will slow cure time. Do not store ARM707X-RM 100% Solids Epoxy Coating at temperatures below 50°F or above 95°F. Do not apply to slabs on grade unless a heavy uninterrupted vapor barrier has been installed under the slab. Do not apply ARM707X-RM 100% Solids Epoxy Coating if the floor is subject to moisture vapor drive or hydrostatic pressure. ARM707X-RM 100% Solids Epoxy Coating will yellow upon prolonged exposure to sunlight or high intensity artificial lights.

NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY
We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the suitability of our product for your particular purpose. Any use or application other than recommended herein is the sole responsibility of the user. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other liability on our behalf with any sale of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ THE MATERIAL SAFETY DATA SHEET AND FOLLOW ALL PRECAUTIONS TO PREVENT BODILY HARM.

Rev 11/21

Documents / Resources

ArmorPoxy ARM707X-RM 100% Solid With Metal Mixer and Bucket [pdf] Instructions
ARM707X-RM, ARM707X-RM 100 Solid With Metal Mixer and Bucket, ARM707X-RM, 100 Solid With Metal Mixer and Bucket, Metal Mixer and Bucket, Bucket

References

User Manual

ArmorPoxy ARM707X-RM 100% Solid With Metal Mixer and Bucket Instructions

ARM707X-RM 100% Solid With Metal Mixer and Bucket

Specifications

Product Usage Instructions

Product Preparation