Arcadyan WN9722HAX22-DM AIOS7 HEOS 7.0 Platform Module User Manual

WN9722HAX22-DM AIOS7 HEOS 7.0 Platform Module

“

Specifications

Basic Specification

• Manufacture: Arcadyan
• Product Name: HEOS 7.0 Platform Module Type DH
• Model Name: WN9722HAX22-DM (AIOS7.0-DH)
• Chip:
  • CPU: Mediatek
  • 2.4GHz:
    • MAC/BB/RF: Mediatek
    • PA(Tx): Mediatek
    • LNA(Rx): Mediatek
    • BPF(Rx): Mediatek
  • 5GHz:
    • MAC/BB/RF: Mediatek
    • PA(Tx): Mediatek
    • LNA(Rx): Mediatek
    • BPF(Rx): Mediatek
  • 6GHz:
    • MAC/BB/RF: Mediatek
    • PA(Tx): Mediatek
    • LNA(Rx): Mediatek
    • BPF(Rx): Mediatek

WLAN Specification

• Chip Interface: SDIO
• Frequencies:
  • 2.4GHz: 2400~2483.5MHz (FCC, CE, JP)
  • 5GHz: 5150~5250MHz (W52, U-NII-1, Band 1)
  • 6GHz: 5945~6425MHz
• Data Rates:
  • IEEE 802.11b: Up to 11Mbps
  • IEEE 802.11ac VHT80: Up to 866.7Mbps
• MIMO: 2T2R

Bluetooth Specification

• Chip Interface: SDIO
• Operating Frequency: 2.4 – 2.4835 GHz
• Modulation: GFSK 250kHz
• Channel Spacing: 1MHz
• Receive Sensitivity: -86dBm at 0.1% BER
• Antenna: External U.FL connector Impedance: 50 Ohm

Antenna List

Set	Ant.	Port Brand	Model Name	Antenna Type	Connector	2.4GHz Gain (dBi)	5GHz Gain (dBi)	6GHz Gain (dBi)	Bluetooth Gain (dBi)

Product Usage Instructions

Setting Up the AIOS7 DH Device:

To set up the AIOS7 DH device, follow these steps:

1. Connect the power adapter to the device.
2. Power on the device by pressing the power button.
3. Wait for the device to boot up and initialize.
4. Follow the on-screen instructions to complete the setup
   process.

Connecting to WLAN:

To connect to a WLAN network, follow these steps:

1. Access the device settings menu.
2. Select the WLAN option.
3. Choose the desired network from the available list.
4. Enter the network password if prompted.
5. Wait for the device to connect to the network.

Frequently Asked Questions (FAQ)

Q: How do I reset the device to factory settings?

A: To reset the device to factory settings, locate the reset
button on the device and press and hold it for at least 10 seconds.
The device will restart, and all settings will be restored to
default.

Q: Can I use the AIOS7 DH device as a Bluetooth speaker?

A: Yes, you can use the AIOS7 DH device as a Bluetooth speaker
by enabling Bluetooth on the device and pairing it with your
smartphone or other Bluetooth-enabled devices.

“`

AIOS7 DH

User Manual

Model Name: WN9722HAX22-DM (AIOS7.0-DH) Brand NameArcadyan

1

AIOS7 DH 1 Specification…………………………………………………………………………………………………………………………………3 1-1 Basic Specification …………………………………………………………………………………………………………………………………………………….. 3
2 Detail Specification
2-1 WLAN Specification …………………………………………………………………………………………………………………………………… 4 2-1-1 Bluetooth Specification ………………………………………………………………………………………………………………………………….. 5 2-2 Antenna List………………………………………………………………………………………………………………………………………………… 6
2

AIOS7 DH

1 Specification

1-1 Basic Specification

2. Item

Contents

Manufacture

Arcadyan

Product Name

HEOS 7.0 Platform Module Type DH

Model Name

WN9722HAX22-DM (AIOS7.0-DH)

Chip

SOC

Vendor

CPU

Mediatek

2.4GHz MAC/BB/RF

Mediatek

2.4GHz PA(Tx)

Mediatek

2.4GHz LNA(Rx)

Mediatek

2.4GHz BPF(Rx)

ACX

5GHz MAC/BB/RF

Mediatek

5GHz PA(Tx) 5GHz LNA(Rx) 5GHz BPF(Rx) 6GHz MAC/BB/RF 6GHz PA(Tx) 6GHz LNA(Rx) 6GHz BPF(Rx)

Mediatek Mediatek ACX Mediatek Mediatek Mediatek ACX

Model name

3

AIOS7.0DH
2 Detail Specification
2-1 WLAN Specification
Item Chip Interface Frequency
Data Rate
MIMO

Specification
SDIO 2400~2483.5MHz(FCC, CE, JP) 2471~2497MHz(JP) 5150~5250MHz(W52, U-NII-1, Band 1) 5250~5350MHz(W53, U-NII-2A, Band 2) 5470~5725MHz(W56, U-NII-2C, Band 3) 5725~5850MHz(W58, U-NII-3, Band 4) DFS support 5945~6425MHz
IEEE 802.11b: 11, 5.5, 2, 1Mbps IEEE 802.11a 54, 48, 36, 24, 18, 12, 9, 6Mbps IEEE 802.11n HT20
Up to 144Mbps IEEE 802.11n HT40
Up to 300Mbps IEEE 802.11ac VHT80
Up to 866.7Mbps IEEE 802.11ax HE80
Up to 1200Mbps 2T2R

Remark

4

AIOS7.0DH

2-1-1 Bluetooth Specification

Item

Specification

Chip

Interface SDIO

Operating Frequency

2.4

–

2.4835 GHz

GFSK 250kHz

Modulation

Adaptive CRC

Frequency

Hopping,

24bit

128bit AES CCM

Channel Spacing

1MHz

Receive Sensitivity

-86dBm at 0.1% BER

Antenna

External U.FL connector Impedance: 50 Ohm

Reark

5

AIOS7.0DH
2-2 Antenna List

Set Ant. Port Brand

Model Name

Antenna Type

Connector 2.4GHz

Gain (dBi) 5GHz 6GHz

Bluetooth

1

1

WIESON

ARY196-0383-00500

Dipole Antenna

I-PEX

–

–

–

2.1

1 2

1

WIESON

ARY196-0383-00600

Dipole Antenna

I-PEX

2.2 2.7 2.8

–

3

2

WIESON

ARY196-0383-00700

Dipole Antenna

I-PEX

1.7 1.6 1.7

–

1

1

WIESON

ARY196-0383-00800

Dipole Antenna

I-PEX

–

–

–

1.7

2 2

1

WIESON

ARY196-0383-00900

Dipole Antenna

I-PEX

2.0 2.2 2.3

–

3

2

WIESON

ARY196-0383-01000

Dipole Antenna

I-PEX

1.1 1.0 0.9

–

1

1

WIESON

ARY196-0383-034H0

PCB Antenna

I-PEX

–

–

–

2.84

3

2

1

WIESON

ARY196-0383-035H0

PCB Antenna

I-PEX

2.8 3.82 4.16

–

3

2

WIESON

ARY196-0383-036H0

PCB Antenna

I-PEX

2.66 3.78 4.23

–

1

1

WIESON

ARY196-0383-039H0

PCB Antenna

I-PEX

–

–

–

2.75

4

2

1

WIESON

ARY196-0383-037H0

PCB Antenna

I-PEX

2.14 2.18 2.26

–

3

2

WIESON

ARY196-0383-038H0

PCB Antenna

I-PEX

2.54 3.38 3.75

–

1

1

WIESON

ARY196-0383-042H0

PCB Antenna

I-PEX

–

–

–

1.82

5

2

1

WIESON

ARY196-0383-040H0

PCB Antenna

I-PEX

1.97 1.9 2.46

–

3

2

WIESON

ARY196-0383-041H0

PCB Antenna

I-PEX

1.15 2.85 3.5

–

1

1

INPAQ

WA-P-LA-01-106

PCB Antenna

I-PEX

–

–

–

2.98

6 2

1

INPAQ

WA-P-LE-03-039

PCB Antenna

I-PEX

2.74 3.42 3.67

–

3

2

INPAQ

WA-P-LE-02-353

PCB Antenna

I-PEX

4.78 5.45 4.64

–

6

AIOS7.0DH

1

1

INPAQ

WA-P-LA-01-107

PCB Antenna

I-PEX

7 2

1

INPAQ

WA-P-LE-02-378

PCB
Antenna

I-PEX

3

2

INPAQ

WA-P-LE-03-041

PCB
Antenna

I-PEX

1

1

INPAQ

WA-P-LA-01-108

PCB Antenna

I-PEX

8 2

1

INPAQ

WA-P-LE-02-380

PCB Antenna

I-PEX

3

2

INPAQ

WA-P-LE-03-042

PCB Antenna

I-PEX

–

–

–

3.4

3.36 2.39 2.62

–

2.53 5.87 4.69

–

–

–

–

3.04

5.46 5.75 7.1

–

5.41 6.09 6.67

–

7

AIOS7.0DH
Normal Setup
· (EUT 1G ETH RJ45 link PCIP domain set to 192.168.50.xxx , use telnet and set IP to 92.168.50.100input “root” then press “enter” button.
Fig. Windows CMD
Fig. Login for telnet 192.168.50.100
Setup EUT to link AP: Prepare an AP device (with wi-fi 5G function)set IP address to 192.168.0.102and set SSID of 5G to “5G” / password : 12345678 # telnet command:
· python3 arc_wifi.py -s 5G -p 12345678 -I 192.168.0.102 #connect AP and EUTset IP address of wlan0 to 192.168.0.102
· ping 192.168.0.101 -I 192.168.0.102 # use wlan0 (192.168.0.102) of EUT to ping 192.168.0.101 which is the IP address of the PC/NB linked AP LAN port.
8

AIOS7.0DH
Fig. Set up Wi-Fi connection between DUT and AP Fig. ping 192.168.0.101 from 192.168.0.102
9

AIOS7.0DH

FCC Statement

Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.
This device is restricted for indoor use. The operation of this device is prohibited on oil platforms, cars, trains, boats, and aircraft, except that operation of this device is permitted in large aircraft while flying above 10,000 feet.
Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or Communications with unmanned aircraft systems.

IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
This module is intended for OEM integrator only. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used.

OEM integrators are responsible for ensuring that the end-user has no manual instructions to remove or install module

The module is limited to installation in mobile or fixed applications, according to Part 2.1091(b). The host manufacturer should reference KDB Publication 996369 D04 Module Integration Guide.

USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be
10

AIOS7.0DH
satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment. If the labelling area is small than the palm of the hand, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. The operation of this device is prohibited on oil platforms, cars, trains, boats, and aircraft, except that operation of this device is permitted in large aircraft while flying above 10,000 feet. Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or Communications with unmanned aircraft systems. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following ” Contains TX FCC ID: RAXAIOS7 “. If the labelling area is larger than the palm of the hand, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC regulations restrict the operation of this device to indoor use only.
11

AIOS7.0DH

IC Statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Dynamic Frequency Selection (DFS) for devices operating in the bands 5250- 5350 MHz, 5470-5600 MHz and 5650-5725 MHz. Sélection dynamique de fréquences (DFS) pour les dispositifs fonctionnant dans les bandes 5250-5350 MHz, 5470-5600 MHz et 5650-5725 MHz.
The device for operation in the band 5150­5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.
The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit. le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer à la limite de p.i.r.e.
The maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate. le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5725-5850 MHz) doit se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point, selon le cas.
For indoor use only. Pour une utilisation en intérieur uniquement.

Devices shall not be used for control of or communications with unmanned aircraft systems. Les appareils ne doivent pas être utilisés pour contrôler ou communiquer avec des systèmes d’aéronefs sans pilote.

Devices shall not be used on oil platforms. Les appareils ne doivent pas être utilisés sur les plates-formes pétrolières.

Devices shall not be used on aircraft, except for the low-power indoor access points, indoor subordinate devices,
low-power client devices, and very low-power devices operating in the 5925-6425 MHz band, that may be used on
large aircraft as defined in the Canadian Aviation Regulations, while flying above 3,048 metres (10,000 feet). Les appareils ne doivent pas être utilisés sur les avions, à l’exception des points d’accès intérieure à faible puissance, des dispositifs subordonnés intérieurs, des dispositifs clients de faible puissance et des dispositifs de très faible puissance fonctionnant dans la bande 5925-6425 MHz, qui peut être utilisée sur de grands avions tel que défini dans la réglementation de l’aviation canadienne, tout en volant au-dessus de 3 048 mètres (10 000 pieds).

Devices shall not be used on automobiles. Les appareils ne doivent pas être utilisés sur les automobiles.

Devices shall not be used on trains. Les appareils ne doivent pas être utilisés dans les trains.

Devices shall not be used on maritime vessels. Les appareils ne doivent pas être utilisés sur les navires maritimes.

12

AIOS7.0DH
IC Radiation Exposure Statement: This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de
distance entre la source de rayonnement et votre corps.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être exploités. Sélection d’autres canaux n’est pas possible.
This radio transmitter (IC: 4711A-AIOS7) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le présent émetteur radio (IC: 4711A-AIOS7) a été approuvé par Industrie Canada pour fonctionner avec les types d’antenne énumérés ci-dessous et ayant un gain admissible maximal d’antenne. Les types d’antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l’exploitation de l’émetteur.
IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used.
Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the IC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied.
The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following ” Contains IC: 4711A-AIOS7 “. The Host Model Number (HMN) must be indicated at any location on the exterior of the end product or product packaging or product literature which shall be available with the end product or online.
Devices shall not be used for control of or communications with unmanned aircraft systems.
13

AIOS7.0DH
Les appareils ne doivent pas être utilisés pour contrôler ou communiquer avec des systèmes d’aéronefs sans pilote.
14

AIOS7.0DH
CE Statement
For MPE Statement ­ Mobile device This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. All operational modes: 2.4GHz: 802.11b, 802.11g, 802.11n (HT20), 802.11n (HT40) , 802.11n (VHT20), 802.11n (VHT40), ,802.11ax (HEW20),802.11ax (HEW40), Bluetooth(BR/EDR, LE), 5GHz: 802.11a, 802.11n (HT20), 802.11n (HT40), 802.11ac (VHT20), 802.11ac (VHT40), 802.11ac (VHT80) ,802.11ax (HEW80), 802.11ax(HEW20),802.11ax (HEW40) 6GHz: 802.11ax (HEW20), 802.11ax(HEW40),802.11ax (HEW80) The frequency and the maximum transmitted power in EU are listed below: 2412-2472MHz: 20 dBm 2402-2480MHz (BR/EDR): 20 dBm 2402-2480MHz (LE): 20 dBm 5180-5240MHz: 23 dBm 5260-5320MHz: 20 dBm 5500-5700MHz: 20 dBm 5745-5825 MHz: 13.98 dBm 5955-6415MHz: 23 dBm
AT BE BG HR CY CZ DK EE FI FR DE EL HU IE IT LV LT LU MT NL PL PT RO SK SI ES SE UK(NI) WLAN: restricted to indoor use only when operating in 5150-5350 MHz band. The device is restricted to indoor use only when operating in the 5945 to 6425MHz frequency range.
Arcadyan Germany Technology GmbH Koelner Strasse 10b, 65760 Eschborn, Germany
15

AIOS7.0DH
Telec Statement
5GHz band (W52, W53): Indoor use only (except communicate to high power radio)
NCC Statement
, CC XX xx LP yyy Z z
16

Documents / Resources

Arcadyan WN9722HAX22-DM AIOS7 HEOS 7.0 Platform Module [pdf] User Manual WN9722HAX22-DM AIOS7 HEOS 7.0 Platform Module, WN9722HAX22-DM, AIOS7 HEOS 7.0 Platform Module, HEOS 7.0 Platform Module, 7.0 Platform Module, Platform Module, Module

References

• User Manual