Cosmic Byte ECLIPSE TRI Mode Controller User Manual

Cosmic Byte ECLIPSE TRI Mode Controller

مواصفات المنتج

ملحوظة: All specifications are for reference and may vary depending on usage and environment.

محتويات الحزمة

• Eclipse Controller × 1
• Replaceable D-Pad × 1
• 2.4G Receiver × 1
• USB Type-C Cable (1.5m) × 1
• دليل المستخدم × 1

أبرز النقاط

Mode Switching Position: From left to right: Bluetooth – 2.4G – NS (Xinput Bluetooth, 2.4G Receiver, Switch)

تعليمات التشغيل

HOME CB Indicator Light

• Blue – iOS and Android
• Orange – 2.4G Mode

اتصال لأول مرة

• 2.4G الوضع اللاسلكي
  • Set the mode switch toggle to 2.4G (Middle).
  • قم بتوصيل مستقبل USB بجهازك.
  • While the controller is powered off, press and hold the Pairing button for 3 seconds.
  • The logo indicator will flash rapidly. Once it turns solid and the controller vibrates briefly, the connection is successful.
• وضع بلوتوث
  • Set the mode switch toggle to Bluetooth (Left).
  • While powered off, press and hold the Pairing button for 3 seconds.
  • The logo indicator will flash rapidly.
  • On your device (PC/Android/iOS), enable Bluetooth and select ‘Xbox Wireless Controller’.
  • When the logo light turns solid and the controller vibrates, the pairing is complete.
• الوضع السلكي
  • Connect the controller to your device using the included USB Type-C cable.
  • Wired mode activates automatically when connected.

إعادة الاتصال
To reconnect to the last paired device (with the same mode), short-press the Home button.

ضبط عصا التحكم

• تبديل المنطقة الميتة:
  • Press and hold Left and Right Stick (LS/RS) for 5 seconds to switch between 5% and 0% deadzone.
  • Controller will vibrate to confirm the change.
• Active Zone Shape Toggle:
  • Press and hold M + LS or RS for 5 seconds to toggle between 10% square zone and 0% circle zone.

 Turbo and Continuous Fire

• توربو يدوي
  • Press M + A while holding the A button to enable manual turbo (continuous fire).
  • Logo light will flash red rapidly.
• توربو أوتوماتيكي
  • Press M + A again to switch to auto turbo. Press again to cancel turbo.
  • A single press of A will now fire continuously.
• Clean all Turbo
  • Press M button twice and hold M for 5 secs, controller will vibrate & clean all Turbo settings.
• ضبط سرعة توربو
  • Hold M + Right Stick Up/Down to increase or decrease turbo speed.
  • Vibration feedback indicates change.

ABXY Lighting Adjustment

• Press M + Right Stick Left and Right to adjust brightness.
• 4 Brightness Levels: 0% → 30% → 70% → 100%

تعديل شدة الاهتزاز

• Press and hold M + Right Stick Up to increase vibration intensity.
• Press and hold M + Right Stick Down to decrease.
• 4 Levels: 0% (off) → 30% → 70% → 100%

مفتاح تخطيط ABXY

Use the layout switch on the front to toggle between XBOX-style and Alternate-style layouts.

Rapid Trigger Adjustment
Adjust LT/RT trigger travel distance using the trigger mode switch on the back for quick/short press functionality.

معايرة

• معايرة العصا والزناد
  • قم بتشغيل وحدة التحكم.
  • يمسك View + M + Menu for 3 seconds to enter calibration.
  • LED1 and LED3 will flash.
  • Rotate both sticks clockwise 3 full turns.
  • Fully press both triggers 3 times.
  • Switch triggers to short travel mode, then press them fully 3 more times.
  • يضعط View للخروج.
  • LED1 and LED3 will stay solid for 5 seconds before powering off.
• معايرة الجيروسكوب
  • Power off the controller and place it on a flat surface.
  • يمسك View + A + B + Home to enter gyro calibration.
  • LED1 and LED2 will flash.
  • After 1 second, press Menu to complete calibration. LEDs will turn off.
  • Calibration must be performed in XBOX (ABXY) layout mode.

Macro Programming (M1/M2 Buttons)

• While connected, hold M + M1 or M2 for 3 seconds to enter programming mode.
• Press the desired button to assign (e.g., A, B, etc.).
• Press M1 or M2 again to save and exit.

ملحوظة: If no button is selected, M1/M2 will be blank. Up to 21 Programmable buttons: A/B/X/Y/D-pad/LB/RB/LT/RT/L3/R3/Menu/View/Joysticks

إيقاف التشغيل

• Hold the Home button for 5 seconds to power off.
• إيقاف التشغيل التلقائي بعد 10 دقيقة من عدم النشاط.

إعادة تعيين وحدة التحكم
Use a small pin to press the Reset hole to restore factory settings.

 Joystick Force Adjustment (Roller-Based)
The Cosmic Byte Eclipse controller features adjustable joystick tension using a built-in roller mechanism. Follow the steps below to customize the joystick force according to your preference:

• Locate the joystick roller at the base of each analog stick.
• To increase joystick resistance, rotate the roller clockwise.
• To decrease joystick resistance, rotate the roller counter-clockwise.
• Make adjustments gradually and test after each rotation to find your preferred setting.

ملحوظة: The roller mechanism allows for fine-tuning of joystick stiffness for better precision or quicker flick response in different game types (e.g., FPS vs Racing).

دليل مؤشر البطارية

• بطارية منخفضة: Logo light flashes red once every 10 minutes
• الشحن: Logo light breathes green
• مشحونة بالكامل: Logo light turns off

تنزيل تطبيق الهاتف المحمول

Download and install the “Key Linker” App from the Google Play Store or Apple App Store for advanced customization and controller adjustments.

ضمان

• The Eclipse Tri-Mode Controller carries a 1-year warranty against manufacturing defects only.
• Physical, water damage, and tampلا يغطي الضمان منتجات ered.

Scan the QR Code to know the Warranty Claim Procedure.

تفاصيل الدعم

• Customer Care Number: +91 7351615161 (Mon-Sat 10am to 6pm)
• WhatsApp Support: +91 7351615161
• بريد إلكتروني: cc@thecosmicbyte.com