ELEGOO Smart Mini Heater for Resin 3D Printer

مقدمة

The ELEGOO Smart Mini Heater is designed to optimize your resin 3D printing experience by providing intelligent temperature control and efficient air filtration. This device ensures stable printing conditions, reducing common issues like print detachment, warping, and poor layer adhesion. It is compatible with a wide range of ELEGOO MSLA/DLP/LCD 3D printers.

مميزات المنتج

التحكم الذكي في درجة الحرارة

The Mini Heater features precise and intelligent temperature control, maintaining optimal stability throughout the printing process. This helps prevent issues such as mid-print detachment, warping, and poor interlayer adhesion, which can compromise print quality.

PTC Rapid Heating & High-Speed Fan

Equipped with advanced PTC heating technology, the Mini Heater provides swift and efficient heating. The PTC element's self-regulating properties prevent overheating, ensuring enhanced safety. A 10,000R/Min high-speed fan ensures optimal airflow and even heat distribution, eliminating hotspots and maintaining consistent temperature for uniform material deposition and remarkable print quality.

Efficient Air Filtration

The Mini Heater incorporates an efficient air filtration system to remove impurities and ensure a clean and purified printer chamber. This feature contributes to a fresh workspace and improved print quality.

ماذا يوجد في الصندوق

• ELEGOO Mini Heater Unit
• دليل المستخدم
• محول الطاقة
• لوحة التركيب
• براغي
• مفتاح ألين
• Additional Carbon Filters (2 units)

الإعداد والتثبيت

Follow these steps to properly install your ELEGOO Mini Heater:

1. Remove the top cover of your compatible ELEGOO 3D printer.
2. Locate the designated mounting area on the back of the printer's top cover. This area typically has a filler plate secured by screws.
3. Remove the existing filler plate.
4. Position the Mini Heater's mounting bracket on the outer side of the top cover's back, aligning it with the screw holes.
5. From the inside of the top cover, use the provided screws and Allen key to secure the mounting bracket. Ensure it is firmly attached.
6. Align the Mini Heater unit with the button hole and screw holes on the mounting bracket and place it in the installation position.
7. Secure the Mini Heater to the mounting bracket using the provided screws and Allen key.
8. Carefully tidy up any cables and replace the top cover onto the printer.
9. Plug the Mini Heater's power cord into the power adapter, and then plug the adapter into a power outlet.
10. Turn on the Mini Heater using its power switch. The unit will automatically begin heating to the optimal temperature.

تركيب الفيديو

تعليمات التشغيل

Once installed and powered on, the ELEGOO Mini Heater operates automatically. It will continuously monitor the internal temperature of your 3D printer's chamber and activate heating when the temperature drops below 25°C, stopping when it reaches or exceeds 25°C. This ensures a consistent and optimal environment for resin printing.

• التسخين المسبق: For best results, it is recommended to turn on the Mini Heater approximately 20-30 minutes before starting a print to allow the resin and printer chamber to reach the desired temperature.
• يراقب: The Mini Heater features a real-time temperature display, allowing you to monitor the chamber temperature.

صيانة

Regular maintenance ensures the longevity and optimal performance of your Mini Heater.

• استبدال فلتر الكربون: The Mini Heater includes an active carbon filter for air purification. These filters should be replaced periodically depending on usage to maintain effective odor and impurity removal. The product comes with two additional carbon filters.
• تنظيف: Keep the exterior of the Mini Heater clean and free from dust and resin spills. Use a soft, dry cloth for cleaning.

Mini Heater PCB Replacement

In case of a malfunction with the heating element or control board, the Mini Heater PCB can be replaced. This is an advanced maintenance task and should only be performed by users comfortable with disassembling and reassembling electronic components.

استكشاف الأخطاء وإصلاحها

• عدم تشغيل السخان: Ensure the power adapter is securely connected to both the Mini Heater and a working power outlet. Check the power switch on the heater.
• Temperature not reaching 25°C: Verify that the printer's cover is securely closed to maintain the internal temperature. In very cold environments, it may take longer to reach the target temperature.
• Print failures (detachment, warping): While the Mini Heater significantly reduces these issues, ensure your resin settings (exposure time, lift speed) are correctly calibrated for your specific resin and printer model. Also, ensure the resin is thoroughly mixed before printing.
• Layer lines or print quality issues: Some users have reported potential issues with layer lines when using heaters, especially if the heater's design interferes with the printer's mechanics or if the temperature fluctuations are not perfectly managed. Ensure the heater is securely mounted and not causing any vibrations. If issues persist, consult ELEGOO support.

تحديد

التوافق

The ELEGOO Mini Heater is designed for seamless integration with a wide range of ELEGOO MSLA/DLP/LCD 3D printers, including:

• ساتورن 4 ألترا 16K
• زحل 4 الترا
• زحل 4
• زحل 3 الترا
• زحل 3
• Saturn 8K
• ساتورن إس
• مارس 5 الترا
• المريخ 5
• Mars 4 Max
• Mars 4 DLP
• Jupiter SE

ملحوظة: It is not recommended to use this heater with other brands of printers unless an opening can be safely cut into the housing and there is sufficient room for the heater unit.

الضمان والدعم

ELEGOO products come with a standard manufacturer's warranty. For specific warranty details, technical support, or service inquiries, please visit the official ELEGOO website or contact ELEGOO customer service directly. You can also find more information and related products at the متجر ELEGOO على أمازون.