FLIPSKY FSESC 6.7 Pro Electronic Speed Controller User Manual

1. المقدمة

This manual provides essential information for the proper installation, operation, and maintenance of your FLIPSKY FSESC 6.7 Pro Electronic Speed Controller. Please read this manual thoroughly before using the product to ensure safe and efficient operation.

2. انتهى المنتجview

The FLIPSKY FSESC 6.7 Pro is an advanced Electronic Speed Controller (ESC) designed for various applications, including electric surfboards, multi-axis aircraft, electric vehicles, electric skateboards, golf carts, smart cars, and robots. It is based on the VESC6 hardware and features a robust aluminum case for enhanced durability and heat dissipation. The unit includes an integrated anti-spark switch for safe power connection.

المميزات الرئيسية:

• Hardware: V 6.7, compatible with Benjamin VESC TOOL.
• المجلدtage Range: 8V - 60V (safe for 3S to 12S LiPo batteries).
• Current Capacity: Continuous 60A, instantaneous peak 150A (performance depends on temperature and air circulation).
• Integrated Anti-spark Switch: For safe power connection.
• Waterproof Aluminum Case: Provides protection and efficient heat management.
• Auxiliary Power Outputs: 5V 1.5A and 3.3V 1A for external electronics.
• Supported Modes: DC, BLDC, FOC (sinusoidal).
• Supported Sensors: ABI, HALL, AS5047.

الشكل 1: الجبهة view of the FLIPSKY FSESC 6.7 Pro, showcasing its compact design and aluminum casing.

الشكل 2: العودة view of the FLIPSKY FSESC 6.7 Pro, highlighting the heat sink design for thermal management.

3. المواصفات

4. محتويات العبوة

عند فتح العبوة، يرجى التأكد من تضمين جميع العناصر التالية:

• 1x FLIPSKY FSESC 6.7 Pro Electronic Speed Controller with Aluminum Case
• شنومكس مايكرو كابل أوسب
• 1x VESC Sensor Wire
• 1x PPM Cable
• 1x LED Button (for anti-spark switch)
• 1x دليل المستخدم (هذه الوثيقة)

Figure 3: The FSESC 6.7 Pro unit alongside its standard accessories, including the USB cable, sensor wire, PPM cable, and LED button.

5. الإعداد والأسلاك

Careful wiring is crucial for the safe and correct operation of the FSESC 6.7 Pro. Refer to the diagrams below for proper connections.

Internal Components and Heat Management:

الشكل 4: داخلي view of the FSESC 6.7 Pro circuit board with the cover removed, showing the layout of components.

الشكل 5: مفصل view of the internal components, including the XT90 wire size, capacitors, MOSFETs, PCB layers, heat transfer pad, and anti-vibration silicon pad, all contributing to efficient operation and heat dissipation.

واجهات الاتصال:

The FSESC 6.7 Pro features various interfaces for connecting to your motor, battery, and control systems. Ensure all connections are secure and correctly oriented.

Figure 6: Comprehensive wiring diagram for the FSESC 6.7 Pro, illustrating the location and numbering of all connection interfaces.

الشكل 7: مكبر view of the pinouts for various interfaces, including CAN, Sensor Voltage, SENSE, SWD, COMM2, COMM1, PPM, and Micro USB, providing clear guidance for connections.

1. اتصال المحرك: Connect the three motor phase wires to the corresponding outputs on the ESC.
2. توصيل البطارية: Connect your LiPo battery (3S-12S) to the XT90 female connector. Ensure correct polarity.
3. Anti-spark Switch: The LED button for the anti-spark switch must be connected before powering on the unit. Failure to do so can damage the switch.
4. سلك الاستشعار: If using a sensored motor, connect the VESC Sensor Wire to the SENSE port.
5. PPM Cable: For remote control input, connect the PPM cable to the PPM port.
6. اتصال USB: Use the Micro USB cable to connect the ESC to a computer for configuration via VESC TOOL.
7. حافلة CAN: The CAN interface (1) allows for communication with other VESC-compatible devices.
8. COMM1/COMM2: These ports (5, 6) support IIC, SPI, and UART communication protocols for external modules.

الترتيب الأولي:

After physical connections, the ESC requires configuration using the VESC TOOL software. This tool allows you to set motor parameters, battery limits, and control modes. Refer to the official VESC TOOL documentation for detailed instructions on software usage and parameter tuning.

6. تعليمات التشغيل

Once the FSESC 6.7 Pro is properly installed and configured, follow these general operating guidelines:

1. تشغيل الطاقة: Ensure all connections are secure. Press the anti-spark LED button to power on the ESC.
2. فحص النظام: Before operating, perform a brief system check to ensure the motor responds correctly to control inputs and there are no unusual noises or vibrations.
3. يراقب: If possible, monitor ESC temperature and battery voltage during operation, especially during initial runs or under heavy load.
4. إيقاف التشغيل: Always power off the ESC using the anti-spark LED button when not in use. Disconnect the battery for long-term storage.

Important Safety Note: Do not exceed the specified voltage and current limits. Overloading the ESC can lead to permanent damage and potential safety hazards.

7. الصيانة

Regular maintenance helps ensure the longevity and reliable performance of your FSESC 6.7 Pro.

• تنظيف: Keep the ESC clean and free from dust, dirt, and moisture. Use a soft, dry cloth for cleaning.
• التفتيشات: Periodically inspect all wiring and connectors for signs of wear, corrosion, or loose connections.
• الإدارة الحرارية: Ensure adequate airflow around the ESC, especially during high-current applications, to prevent overheating. The aluminum case is designed for heat dissipation, but external cooling may be necessary in extreme conditions.
• تحديثات البرامج الثابتة: Check the official FLIPSKY or VESC project website for firmware updates. Updating firmware can improve performance and add new features.

8. استكشاف الأخطاء وإصلاحها

If you encounter issues with your FSESC 6.7 Pro, consider the following troubleshooting steps:

• لا يوجد طاقة:
  • تحقق من توصيلات البطارية وتأكد من شحنها.
  • Verify the anti-spark LED button is correctly connected and pressed.
• Motor Not Spinning/Erratic Behavior:
  • Confirm motor phase wire connections are secure.
  • Check sensor wire connections if using a sensored motor.
  • Review VESC TOOL configuration for correct motor detection and parameter settings.
  • Ensure the PPM cable (or other control input) is correctly connected and calibrated.
• ارتفاع درجة الحرارة:
  • تقليل الحمل أو وقت التشغيل.
  • تحسين تدفق الهواء حول وحدة التحكم الإلكترونية.
  • تحقق من وجود دوائر قصر في ملفات المحرك أو الأسلاك.
• Communication Issues (VESC TOOL):
  • Ensure the Micro USB cable is properly connected.
  • حاول استخدام منفذ USB أو كابل مختلف.
  • Verify VESC TOOL is the latest version and drivers are installed.

For persistent issues, consult online VESC communities or contact FLIPSKY customer support.

9. الضمان والدعم

FLIPSKY products are manufactured to high-quality standards. For warranty information and technical support, please refer to the official FLIPSKY webالموقع أو تواصل مع بائع التجزئة. احتفظ بإثبات الشراء لطلبات الضمان.