Intex Sand Filter Pump Repair Kit

1. المقدمة

This manual provides instructions for the Intex Sand Filter Pump Repair Kit, Model 25013. This kit is designed to replace worn or damaged O-rings and the air release valve in compatible Intex sand filter pumps, helping to resolve leaks and maintain efficient pump operation. Proper installation of these components is crucial for the longevity and performance of your pool's filtration system.

2. معلومات السلامة

• افصل الطاقة دائمًا to the sand filter pump before performing any maintenance or repair.
• Depressurize the system by opening the air release valve and ensuring all pressure is relieved before opening any part of the pump.
• ارتدِ معدات الحماية الشخصية المناسبة، مثل القفازات وحماية العين.
• إبقاء جميع الأجزاء بعيدا عن متناول الأطفال.
• Refer to your specific Intex sand filter pump's original manual for detailed disassembly and reassembly procedures.

3. محتويات المجموعة والتوافق

The Intex Sand Filter Pump Repair Kit (Model 25013) includes essential replacement parts for various Intex sand filter pumps. This kit is compatible with select Intex sand filter pumps, particularly those requiring part number 25013.

المكونات المتضمنة:

• 1 Tank O-ring (for 12 and 14 inch sand filter pumps and combos, part 11379)
• 1 Drain Valve O-ring (for sand filter pump and combo, part 11385)
• 1 L-shape O-ring (for sand filter pump motor, part 11412)
• Additional assorted O-rings for various pump sections.
• 1 Air Release Valve.

Image: Assortment of black O-rings of various sizes included in the kit.

Image: Two large and two small black O-rings, illustrating different sizes.

Image: A gray plastic air release valve, a key component for pump maintenance.

Image: Three black O-rings of varying sizes, demonstrating the range of seals provided.

4. الإعداد والتثبيت

Replacing O-rings and the air release valve requires careful attention to detail. Always refer to your specific Intex sand filter pump's instruction manual for exact steps related to its model.

خطوات التثبيت العامة:

1. انقطاع التيار الكهربائي: Ensure the pump is turned off and unplugged from the power source.
2. نظام تخفيف الضغط: Open the existing air release valve to relieve any pressure within the filter system.
3. استنزاف المياه: If necessary, drain water from the pump and filter tank according to your pump's manual.
4. التفكيك: Carefully disassemble the pump components to access the O-rings and air release valve that need replacement. Note the position and orientation of each part.
5. إزالة الأجزاء القديمة: Remove the old, worn, or damaged O-rings and the air release valve. Inspect the surfaces where the new parts will be seated for any debris or damage.
6. تثبيت أجزاء جديدة: Lightly lubricate new O-rings with a silicone-based lubricant (do not use petroleum-based lubricants as they can degrade rubber) before seating them into their grooves. Install the new air release valve. Ensure all parts are seated correctly and without twists or pinches.
7. إعادة التجميع: Reassemble the pump components, ensuring all connections are secure and tightened appropriately. Do not overtighten.
8. اختبار التسريبات: Once reassembled, slowly turn on the pump and check for any leaks. If leaks occur, turn off the pump, depressurize, and re-check the installation of the O-rings and connections.

5. اعتبارات التشغيل

After successfully replacing the O-rings and air release valve, your Intex sand filter pump should operate without leaks and maintain proper pressure. Monitor the pump's performance for the first few hours of operation to ensure all seals are holding correctly. The air release valve should be used to purge air from the system during initial startup or after any maintenance that exposes the system to air.

6. الصيانة

Regular maintenance of your sand filter pump's O-rings and seals is essential for preventing future leaks and ensuring efficient operation.

• التفتيش الدوري: Annually, or at the beginning of each pool season, inspect all accessible O-rings for signs of wear, cracking, or flattening. Replace any damaged O-rings promptly.
• تشحيم: Lightly lubricate O-rings with a silicone-based lubricant during reassembly or annual inspection to maintain their flexibility and sealing capability.
• التخزين السليم: If storing the pump for the off-season, ensure it is clean and dry. Store any spare O-rings in a cool, dry place away from direct sunlight and chemicals.

7. استكشاف الأخطاء وإصلاحها

إذا واجهت مشكلات بعد تثبيت مجموعة الإصلاح، ففكر فيما يلي:

• التسريبات بعد التثبيت:
  • Ensure O-rings are correctly seated in their grooves and not twisted or pinched.
  • Verify that all connections and clamps are tightened securely, but not excessively.
  • Check for any nicks or damage on the O-rings that might have occurred during installation.
• الهواء في النظام:
  • Ensure the air release valve is properly installed and closed after purging air.
  • Check all suction side connections for air leaks.
• Low Flow/Pressure:
  • Confirm the pump basket and skimmer basket are clean.
  • Backwash the sand filter if the pressure gauge indicates high pressure.

8. المواصفات

9. الضمان والدعم

For specific warranty information regarding your Intex Sand Filter Pump Repair Kit or for further technical assistance, please refer to the official Intex website or contact Intex customer support directly. Keep your purchase receipt as proof of purchase.

Intex Customer Support: يرجى الزيارة www.intexcorp.com/support/ للحصول على معلومات الاتصال والأسئلة الشائعة.