1. انتهى المنتجview
This manual provides essential information for the installation, use, and maintenance of the Fiamma 98656-074 Upper Bracket.
The Fiamma 98656-074 is a replacement upper fixing bracket designed specifically for Fiamma carry-bike bike racks. It is suitable for use with VW T4 and T4D bike rack models.
الشكل 1: The Fiamma 98656-074 Upper Bracket. This image shows the black metal bracket with its distinctive curved shape and two mounting holes at the base, designed for secure attachment to a bike rack system.
محتويات الحزمة:
- 1 x Fiamma 98656-074 Upper Bracket
المميزات الرئيسية:
- Designed as a direct replacement part for Fiamma Carry-Bike systems.
- Specifically compatible with VW T4 and T4D models.
- Features an "Easy Snap" mounting type for straightforward installation.
- مصنوعة من مواد متينة لأداء طويل الأمد.
2. الإعداد والتثبيت
This section outlines the general steps for installing the Fiamma 98656-074 Upper Bracket. Always refer to your specific Fiamma Carry-Bike rack manual for detailed instructions and safety warnings.
Tools Required (Typical):
- Appropriate wrenches or sockets (size may vary depending on existing hardware)
- Measuring tape (optional, for alignment)
خطوات التثبيت:
- السلامة أولاً: Ensure the vehicle is parked on a level surface and the bike rack is stable. If replacing an existing bracket, ensure no load is on the rack.
- قم بإزالة الدعامة القديمة (إن وجدت): Carefully unbolt and remove the existing upper bracket from your Fiamma Carry-Bike rack. Note the orientation and position for reference.
- تحديد موقع القوس الجديد: Align the new Fiamma 98656-074 Upper Bracket with the designated mounting points on your bike rack. Ensure the "Easy Snap" mechanism (if present) engages correctly.
- السحابات الآمنة: Insert the appropriate bolts and washers through the mounting holes. Hand-tighten all fasteners initially.
- الشد النهائي: Using the correct tools, tighten all fasteners securely. Do not overtighten, as this can damage the bracket or the rack. Refer to your bike rack manual for specific torque specifications if available.
- التحقق من الاستقرار: After installation, gently test the bracket's stability and ensure it is firmly attached to the bike rack.
It is recommended to have the installation performed by a qualified professional if you are unsure about any steps.
3. التشغيل
The Fiamma 98656-074 Upper Bracket functions as a fixed component of your Fiamma Carry-Bike rack system. Its primary role is to provide a secure upper attachment point for the bike rack to the vehicle, specifically for VW T4 and T4D models.
Once correctly installed, the bracket requires no further operational input. Its function is passive, ensuring the structural integrity and stability of the bike rack during transport.
Always ensure that all components of your bike rack, including this bracket, are in good condition and properly secured before each use, especially when transporting bicycles.
4. الصيانة
Regular maintenance ensures the longevity and safe operation of your Fiamma 98656-074 Upper Bracket and the entire bike rack system.
الفحوصات الروتينية:
- التفتيش البصري: Periodically inspect the bracket for any signs of wear, corrosion, cracks, or deformation.
- فحص المثبتات: Regularly check that all bolts and fasteners securing the bracket are tight. Vibrations during travel can sometimes loosen connections.
- نظافة: Keep the bracket clean from dirt, mud, and road salt, which can accelerate corrosion. Use a mild soap and water solution, then rinse thoroughly and dry.
- التشحيم (إن وجد): If any moving parts or pivot points are associated with the bracket's connection (though unlikely for a fixed bracket), apply a suitable lubricant as recommended by the bike rack manufacturer.
Replace the bracket immediately if any damage or significant wear is observed to ensure safety.
5. استكشاف الأخطاء وإصلاحها
This section addresses common issues you might encounter with the Fiamma 98656-074 Upper Bracket.
| مشكلة | السبب المحتمل | حل |
|---|---|---|
| Bracket does not fit correctly. | Incorrect model bracket for your bike rack or vehicle. | Verify that your bike rack is a Fiamma Carry-Bike system and is compatible with VW T4/T4D models. Confirm the bracket model number (98656-074). |
| يبدو الحامل مرتخياً بعد التركيب. | Fasteners not tightened sufficiently or incorrect fasteners used. | Ensure all bolts and nuts are correctly installed and tightened to the manufacturer's specifications. Check for missing washers or damaged threads. |
| Visible damage or corrosion on the bracket. | Normal wear and tear, exposure to harsh elements, or impact. | The bracket is a safety-critical component. If damaged, it must be replaced immediately with a genuine Fiamma part. |
If you encounter issues not listed here or are unable to resolve a problem, contact Fiamma customer support or a qualified service technician.
6. المواصفات
| يصف | التفاصيل |
|---|---|
| ماركة | فياما |
| رقم الموديل | 98656-074 |
| نوع المنتج | Replacement Upper Fixing Bracket |
| التوافق | Fiamma Carry-Bike VW T4 & T4D bike racks |
| وزن العنصر | 6.7 أونصة (حوالي 190 جرامًا) |
| أبعاد المنتج (الطول × العرض × الارتفاع) | 12.6 × 3.94 × 7.87 بوصة (حوالي 32 × 10 × 20 سم) |
| نوع التركيب | Easy Snap |
| بلد المنشأ | إيطاليا |
| لون | Neutral (typically black) |
7. الضمان والدعم
For specific warranty information regarding the Fiamma 98656-074 Upper Bracket, please refer to the documentation provided with your original Fiamma Carry-Bike rack or contact Fiamma directly.
Fiamma products are typically covered by a manufacturer's warranty against defects in materials and workmanship. Keep your proof of purchase for any warranty claims.
دعم العملاء:
For technical assistance, spare parts, or further inquiries, please visit the official Fiamma website or contact their customer service department. Contact details can usually be found on their webالموقع أو في العبوة الأصلية للمنتج.
When contacting support, please have your product model number (98656-074) and any relevant purchase information ready.
