Aputure Light torm User Manual
IMPORTANT SAFETY INSTRUCTIONS
When using this unit, basic safety precautions should always be followed, including the following:
- Read and understand all instructions before using.
- Close supervision is necessary when any fixture is used
by or near children. Do not leave the fixture unattended while in use. - Care must be taken as burns can occur from touching hot surfaces.
- Do not operate the fixture if a cord is damaged, or if the fixture has been dropped or damaged, until it has been examined by qualified service personnel.
- Position any power cables such that they will not be tripped over, pulled, or put into contact with hot surfaces.
- If an extension cord is necessary, a cord with an amperage rating at least equal to that of the fixture should be used. Cords rated for less amperage than the fixture may overheat.
- Always unplug the lighting fixture from the electrical outlet before cleaning and servicing, or when not in use. Never yank the cord to remove the plug from the outlet.
- Let the lighting fixture cool completely before storing.
- To reduce the risk of electric shock, do not immerse this fixture in water or any other liquids.
- To reduce the risk of fire or electric shock, do not disassemble this fixture. Contact cs@aputure.com or take it to qualified service personnel when service or repair work is required. Incorrect reassembly may cause electric shock when the lighting fixture is in use.
- The use of an accessory attachment not recommended by the manufacturer may increase the risk of fire, electric shock, or injury to any persons operating the fixture.
- Power this fixture by connecting it to a grounded outlet.
- Please remove the protective cover before powering on the light. Please remove the protection cover before using the reflector
- Please do not block the ventilation and do not look at the light directly when it is powered on.
CAUTION:
DO NOT TOUCH LED LIght surface
- Please do not place the LED lighting fixture near any liquids or other flammable objects.
- Only use a dry microfiber cloth to clean the product.
- Please have the product checked by an authorized service personnel agent if your product has a problem.
- The malfunctions caused by unauthorized disassembly are not covered under the warranty.
- We recommend only using the original Aputure cable accessories. Please note that our warranty for this product does not apply to any repairs required due to any malfunctions of unauthorized Aputure accessories, although you may request such repairs for a fee.
- This product is certified by RoHS, CE, KC, PSE, and FCC. Please operate the product in full compliance with the operation standards. Please note that this warranty does not apply to repairs arising from malfunctions, although you may request such repairs on a chargeable basis.
- The instructions and information in this manual are based on thorough, controlled company testing procedures. Further notice will not be given if the design or specifications change.
SAVE THESE INSTRUCTIONS
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a different circuit than the receiver is connected to. Consult the dealer or an experienced radio/TV technician for help.
RF Warning Statement:
This device has been evaluated to meet general RF exposure requirements.
Check list
When you unbox the product, please make sure all the items listed below are included. Otherwise, please contact the seller immediately.
- Protection
Cover (1 pc)
300x Lamp
Head (1 pc) - Cable Relief Hook
(1 pc)
- Quick-Release
“Lightning Clamp”
(1 pc)
- Paracord
Strap(1 pc)
Control Box
(1 pc) - VA-Remote RC1+
(1 pc)
- 55° Hyper-Reflector
(1 pc)
- Neutrik® powerCON AC
Power Cable (6m) (1 pc)
- 5-Pin Male-to-Female
XLR Head Cable (3m) (1 pc)
- Carrying Case
(1 pc)
Product Details
- Light
- Bowens Mount
- LED Light Source
Optical Blending
Prism - 55° Hyper-Reflector
- Yoke
- Cable Relief Hook
- T-Handle
/ Baby Pin
Mounting Screw - Baby Pin Receiver/Mounting
Column (5/8in. / 16mm)
- Bowens Mount
Release Latch
- 5-Pin Male XLR Receiver
- Ratcheting Disk
Brake Handle
- Label
- Controller box
- Paracord Strap Plate
- OLED Display
- Channel Setting / FX: Intensity Selection
- Lighting Control Mode / FX: Lighting Eects Toggle
- Brightness Control Wheel / Menu Button
- CCT Control Wheel / Preset Button
- Power Button
- Group Setting / FX: Frequency Selection
- Wireless Control Selection / FX: Trigger
- Antenna Box
- Floor Stand
- USB Port
- Quick-Release Plate
- Battery Plate (*Anton Bauer or V-mount)
- Floor Stand
- 5-Pin Female XLR Power Output
- DMX IN Port
Neutrik power CON Power Input
DMX OUT Port
- VA-Remote RC1+
- Channel Indicators
- Group A On/Off
- Group B On/Off
- Group C On/Off
- FX Button
- Group D On/Off
- Channel Selector
- Group A Dimming Controls
- Group B Dimming Controls
- Group C Dimming Controls
- Group C Frequency & CCT Controls
- Group D Frequency & CCT Controls
Installing
- Installing the cable relief hook
- Attaching/detaching the protection cover
Pull back the retaining pin, rotate the cover clockwise, then detach the cover. To reattach the cover, insert it into the Bowens mount and rotate counterclockwise.
Notice: Always remove the protection cover prior to turning on the light. Always re-install the cover when packing - Attaching/detaching the Hyper-Reflector
To install the reflector, pull back the retaining pin, insert the reflector into the Bowens mount, and rotate it counterclockwise as shown in the following pictures. To remove the reflector, pull back the retaining pin and rotate the reflector clockwise.
- Setting up the Light
Mount the light onto a light stand, then fix it in place using the T-Handle/Mounting Screw on the Baby Pin Receiver/Mounting Column (5/8in. / 16mm). Then loosen/tighten the handbrake locking mechanism on the yoke to adjust the fixture’s angle of tilt.
- Instructions for the Quick-Release “Lightning Clamp”
- Clamp the Lightning Clamp onto a light stand.
- To attach the control box, rotate the release lever to unlock the quick-release baseplate, then mount the control box onto the Lightning Clamp (the release lever will automatically spring back).
- To remove the control box, grasp it firmly, then unlock the quick-release plate by turning the release lever, and detach the control box.
SpecificationsWeight 670g /1.48lbs Sizes(L*W*H) 10.35×8.74×12.5cm / 4.07×3.44×4.92in The Quick-Release “Lightning Clamp” can clamp onto square or round pipe with a diameter between 2-5cm or 0.79-1.97in. - Connect the light to the control box
Connect the light to the control box using the 5-Pin Male-to-Female XLR Head Cable.
- Powering up the controller 1) Powering by AC
- Powering by AC
Neutrik® powerCON
Male Connector
Neutrik® powerCON Female
Locking Connector
To disconnect the Neutrik® powerCon cable, pull back on the yellow release tab on the
cable connector, and rotate the connector counterclockwise.- Powering by Batteries
V-Mount Battery
Anton Bauer Battery
- Batteries: Voltage 12~16.8V; Recommended ≥15A continuous discharge.
- The LS 300x can be operated using a single battery for up to half of the mxture’s maximum output. Plugging the light into AC power
or using two batteries allows you to utilize the light’s full output. When powering the light from a single battery, you mu t install the s
battery on the right side of the of the control box, or the light will not turn on. - Do not use non-14.4v batteries (batteries with voltages outside of the 12-16.8V range). Using higher voltage batteries will damage the power supply and the lighting mxture.
- Only use batteries that support the necessary continuous current discharge special cations mentioned above. If non-compatible batteries are used, the batteries will enter a protection state and the lighting mixture will not operate as intended.
- Customers can choose V-Mount or A-Mount battery plates for their control boxes upon purchase according to their needs
- Powering by Batteries
- Powering by AC
- Insert the button battery to power VA-Remote RC1+
- Remove battery compartment
- Install button battery and insert it into the VA-Remote RC1+
- Remove battery compartment
Operations
- Press the power button to turn the light on and off
- Brightness
- Battery Level/ AC Power Symbol
- Wireless Control Mode
- Remaining Operating Time
- Dimming Curve
- Groups
- Channels
- CCT
- Manual Control
- Rotate the Brightness Control Wheel to adjust the intensity of the light from 0-100%.
- ) Rotate the CCT Control Wheel to adjust the color temperature of the light from 2700K-6500K.
- ) Lighting FX Mode
Press and hold the Eects button for 2 seconds to activate Lighting FX mode, then short press the Eects button to toggle between Paparazzi, Fireworks, Faulty Bulb, Lightning, TV, Pulsing, Strobe, Explosion, Fire, etc.- Paparazzi Effect
- b. Fireworks Effect
- c. Faulty Bulb Effect
- Lightning Effect
As of writing this the Fireworks eect worked in a CCT range presets include three choices of 3200K/5600K/Random.
When controlling the lightning effect, short press the Trigger button to single trigger the lighting effect; long press the Trigger button to enter the Lightning Cycle Mode. - TV Effect
- Pulsing Effect
- Strobe Effect
- Explosion Effect
- i. Fire Effect
As of writing this the TV effect worked in CCT range presets and you cannot set a fixed base CCT.
When controlling the explosion effect, short press the Trigger button to single trigger the lighting effect.
When in Lighting FX mode, short press the “Intensity” button to enter Intensity Adjustment Mode. Then rotate the Brightness Control Wheel to adjust the intensity from 10%-100% as displayed on the screen.
When in Lighting FX mode, short press the “Frequency” button to enter Frequency Adjustment Mode. Then rotate the Brightness Control Wheel to adjust the frequency of the eect from 1 to 10 and R (Random) as displayed on the screen.
When in Lighting FX mode, rotate the CCT Control Wheel to adjust the base CCT of the lighting effect from 2700K to 6500K as displayed on the screen.
As of writing, you cannot set a fixed base CCT for certain eects, such as: Fireworks, TV, and Fire.
If the light is powered o, upon turning on again, the light will resume its last saved setting
- Paparazzi Effect
- ) Wireless Connectivity Modes
Press the Wireless/Trigger button in order to switch between 2.4GHz Wireless Remote Control, Bluetooth SIG Mesh Sidus Link App Control, and no wireless control.
*When setting up the device with the Bluetooth mobile application, the corresponding name of the
fixture is LS 300x (six digits + letters represent the fixture’s serial number) - Press the MENU button to enter the system menu interface, as shown below.
- Output Mode
DMX Mode
Dimming Curve
Fan Mode - Stduo Mode
BT Reset
Language
USB Mode - Exit
Ver:1.0
- Output Mode
- DMX mode
Press the MENU button to enter the system menu, rotate the dimming wheel to select DMX mode and press the MENU button again to enter DMX mode.
When in DMX mode, rotate the brightness control wheels to set the device’s DMX
channel. Then press the MENU button to take you back to the Menu interface
- Dimming curve mode
Press the MENU button to enter the system menu, rotate the dimming wheel to select Dimming Curve, and press the MENU button again to enter the dimming curve selection menu. Using the wheel to choose from exponential (Exp), logarithmic (Log), S-Curve, or linear dimming curves, and press the MENU button to make your selection.
- Fan mode
Press the MENU button to enter the system menu, rotate the dimming wheel to select Fan Mode, and press the MENU button again to enter Fan Mode. Use the wheel to select between Force* and Auto, then press the MENU button to confirm your selection.
In “Force Mode” the fan will continuously spin at its maximum speed. In “Auto Mode” the fan will only
begin spinning when the light has reached 45°C.
- Studio mode
Press the MENU button to enter the system menu, rotate the dimming wheel to select Studio Mode, and press the MENU button again to enter the Studio Mode menu. Once in the menu, use the wheel to choose between “YES”*** or “NO” and press the MENU button to confirm your selection.
When Studio Mode is active, the light will turn on as soon as it receives power, without having to
press the power button.
The light must be connected to your mobile device using the Sidus Link mobile application, and not via your device’s typical Bluetooth connection menu.
Studio Mode is active as the factory default.
- Bluetooth reset
- Press the MENU button to enter the system menu, rotate the dimming wheel to select BT Reset. Press the MENU button again to enter the Bluetooth Menu. Use the wheel to select “YES” to reset the Bluetooth pairing (the pop-up window displays the current reset progress and is completed within 5 seconds); or select “NO” to return to the previous menu.
- After resetting the light’s Bluetooth connection, your mobile phone or tablet will be able to connect to and control the light.
- If the Bluetooth Reset fails, a [Reset Failed] screen will pop-up, and the light will return to Bluetooth mode after 2 seconds.
The light must be connected to your mobile device using the Sidus Link mobile application, and
not via your device’s typical Bluetooth connection menu.
- Press the MENU button to enter the system menu, rotate the dimming wheel to select BT Reset. Press the MENU button again to enter the Bluetooth Menu. Use the wheel to select “YES” to reset the Bluetooth pairing (the pop-up window displays the current reset progress and is completed within 5 seconds); or select “NO” to return to the previous menu.
- Language
Press the MENU button to enter the system menu, rotate the dimming wheel to select Language, and press the MENU button again to enter the Language menu*. Use the wheel to select from the available languages. Initial languages include “English” and “Chinese”.
The factory default language is English.
- USB Mode
- The control box has a built-in USB port for firmware updates (for both the control box and lamp head). Insert a compatible USB* flash drive into the USB port.
- To update the light’s firmware, press the MENU button to enter the system menu, rotate the dimming wheel to select USB Mode, and press the MENU button again to enter the Update menu. Use the wheel to select “YES” or “NO”. If a USB flash drive containing a firmware update is mounted in the USB port, the screen will display an update progress bar**. If you choose “NO”, press MENU button then it will return the
menu interface. - If a USB flash drive is not inserted into the USB port of the flash drive does not contain a firmware upgrade file, entering the Update menu and choosing “YES” will return you to the system menu interface.
Only FAT16 and FAT32 storage formats can be used for firmware updates. Incompatible formats
will result in the screen displaying a format error and will return to the main menu.
DO NOT unplug the light or the USB flash drive during the update process. In the case of an unexpected power failure, DO NOT remove the USB flash drive. When the power is restored, the fixture will automatically resume the update process. After successfully updating the firmware, the fixture will automatically restart.
- OTA Mode
You can also do an OTA wireless firmware update using the Sidus Link mobile app.
- Rotate the Brightness Control Wheel to adjust the intensity of the light from 0-100%.
- Remote Control
You can control the LS 300x from any channel or group configuration Light Storm lights have three channels (1/2/3) and four groups (A/B/C/D). Only groups “C” or “D” can be used to control brightness, CCT and lighting effects, whil groups “A” and “B” can only be used to control brightness.- Configuring channel and group settings on the control box Press the CHANNEL button to toggle between channels 1, 2, & 3.
Press the GROUP button to toggle between groups A, B, C, & D.
- Configuring channel settings on the remote
- Adjusting brightness
Press A/B/C/D to toggle the lights on or o, press (
/
) to adjust the brightness of the light from 0 to 100% accordingly
This remote will not work when the light is in DMX mode.
The remote control will only control the operation of the light when the fixture is in 2.4Ghz Wireless Control Mode.
- CCT Control
In normal light control mode, press the (
/
) buttons to adjust the light’s output CCT.
In FX Mode, press the (
+ / ) buttons to adjust the lights output CCT.
The remote control can only be used to adjust CCT if the lights are in groups C or D.
page 18…………………. - FX Control
Press the ( +
/ ) button to enter or exit lighting eect mode. Press the ( + / ) to toggle between dierent eects.
Press the ( / ) buttons to adjust the output of the light. Press the ( / ) buttons to toggle the eect frequency.
Enter or Exit Eect Mode
a. Paparazzi Mode
b. Fireworks Mode
c. Faulty bulb Mode
d. Lightning Mode
e. TV Mode
f. Pulsing Mode
g. Strobe Mode
h. Explosion Mode
i. Fire Mode
The remote control can only be used to operate lighting eects if the lights are in groups C or D.
- Configuring channel and group settings on the control box Press the CHANNEL button to toggle between channels 1, 2, & 3.
- Connecting to DMX
- Connect a standard DMX controller
Connecting DMX to only one 300x
Daisy chaining multiple lights using DMX
The DMX interface schematic is shown in the pictures below
1.Signal Common
2.Data 1-
(Primary Data Link
3.Data 1+
(Primary Data Link)
4.Data 2-
(Optional Data 1- Secondary Data Link)
5.Data 2+
(Optional Secondary Data Link)
1.Signal Common
2.Data 1-
(Primary Data Link)
3.Data 1+
(Primary Data Link)
4.Data 2- (Optional
Secondary Data Link)
5.Data 2+ (Optional
Secondary Data Link)
- Channel Selection
In DMX mode, match the channel of your DMX controller with the light, and then adjust accordingly.
The default DMX channel is “001”.
The range of DMX channels is 1 to 512.
- Connect a standard DMX controller
- Controlling Device Via DMX
- Connect the DMX controller’s OUTPUT to the 300x’s controller INPUT as shown in the figure below.
- DMX Chart
DMX Channel Values / Functions （6 DMX Channels） Channe Value Function 1 0-255 Dimmer Intensity 0 to 100% CCT Control 2 0-5 2700K 6-10 2800K 11-15 2900K 16-20 3000K 21-25 3100K 26-30 3200K 31-35 3300K 36-40 3400K 41-45 3500K 46-50 3600K 51-55 3700K 56-60 3800K 61-65 3900K 66-70 4000K 71-75 4100K 76-80 4200K 81-85 4300K 86-90 4400K 91-95 4500K 96-100 4600K 101-105 4700K 106-110 4800K 111-115 4900 116-120 5000K 121-126 5100K 131-135 5300K 136-140 5400K 141-145 5500K 146-150 5600K 151-155 5700K 156-160 5800K 161-165 5900K 166-170 6000K 171-175 6100K 176-180 6200K 181-185 6300K 186-190 6400K 196-255 Undefined 3 Frequency Control 0-19 1 20-39 2 40-59 3 60-79 4 80-99 5 100-119 6 120-139 7 140-159 8 160-179 9 180-199 10 200-219 R 220-255 Undefined 4 Mode Selection 0-127 Manual Mode 128-255 FX Mode 5 FX Contro 0-19 Paparazz 20-39 Fireworks 40-59 Faulty Bulb 60-79 Lightning 80-99 TV 100-119 Pulsing 120-139 Strobe 140-159 Explosion 160-178 160-178 180-255 Undefined IN Lightning mode 6 0 Start Point 1-127 Single Trigger 128-255 Cycle Mode IN Explosion mode 0 Start Point 1-127 Single Trigger 128-255 Undefined
- Connect the DMX controller’s OUTPUT to the 300x’s controller INPUT as shown in the figure below.
- Using the Sidus Link APP
You can download the Sidus Link app from the iOS App Store or Google Play Store for enhance the functionality of
the light. Please visit sidus.link/app/help for more details regarding how to use the app to control your Aputure lights.
Specifications
| Operating,Current | 3.5A | Power Consumption | 350W maximum |
| Power Supply | AC 100～240V 50/60Hz | Cooling Mode | e CRI Remote Ability Active Cooling |
| TLCI | ≥96 | CQS | ≥95 |
| CRI | ≥96 | Color Temperature | 2700K~6500K |
| Radio Frequency | 2.4GHz | Channels | 1/2/3 |
| Groups | A/B/C/D | Remote Ability | ≤100m |
| Battery requirement | 12V-16.8V>15A | APP Control Type | Bluetooth |
| Sizes (L*W*H | Light | 29.84*21.56*34.45cm / 11.75*8.49*13.56in | |
| Controller box
Anton Bauer Battery |
27.86*12.67*8.73cm / 10.97*4.99*3.44in | ||
| Controller box
(V-Mount) |
27.86*12.67*9.67cm / 10.97*4.99*3.81in | ||
Photometrics
| CCT | Distance | 1m | 3m | 5m |
| 3200K | Bare Bulb | 474 (fc) | 54 (fc) | 20 (fc) |
| 5100 (lux) | 580 (lux) | 220 (lux) | ||
| Hyper-Reflector | 1505 (fc) | 121 (fc) | 42 (fc) | |
| 16200 (lux) | 1300 (lux) | 450 (lux) | ||
| 4300K | Bare Bulb | 697 (fc) | 74 (fc) | 32 (fc) |
| Hyper-Reflecto | 24300 (lux) | 2100 (lux) | 700 (lux) | |
| 5500K | Bare Bulb | 585 (fc) | 65 (fc) | 23 (fc) |
| 6300 (lux) | 700 (lux) | 250 (lux) | ||
| Hyper-Reflector | 1904 (fc) | 158 (fc) | 51 (fc) | |
| 20500 (lux) | 1700 (lux) | 550 (lux) |
Trademarks
Bowens is a trademark registered by Bowens in China and other countries.
Anton Bauer is a trademark registered by Anton Bauer in the US and other countries.
Neutrik® is a trademark registered by Neutrik® in the US and other countries.
APUTURE GURANTY CARD
| Serial No. | |
| Item Name | |
| Purchase Date | |
| Buyer Name | |
| Buyer Phone | |
| Buyer Add | |
| Franchiser Seal |
APTURE Imaging industrines.co.,Ltd.
inspection:qualified
Service Warranty(EN)
Aputure Imaging Industries Co., Ltd. warrants the original consumer purchaser from defects in material and workmanship for a period of one (1) year after the date of purchase. For more details of warranty visit www.aputure.com
Important: Keep your original sales receipt. Be sure the dealer has written on it the date, serial No. of the product. This information is required for warranty service.
This warranty does not cover:
- Damage that is the result of misuse, abuse, accident (including but not limited to damage by water), faulty connection, defective or maladjusted associated equipment, or the use of the product with equipment for which it was not intended.
- Cosmetic defects that appear more than thirty (30) days after the date of purchase. Cosmetic damage caused by improper handling is also excluded.
- Damage that occurs while the product is being shipped to whoever will service it.
This warranty is void if: - The product identification or serial No. label is removed or defaced in any way.
- The product is serviced or repaired by any one other than Aputure or an authorized Aputure dealer or service agency.
Aputure Imaging Industries Co., Ltd. Add: F/3, Building 21, Longjun industrial estate, HePing West Road, Shenzhen, Guangdong E-MAIL: cs@aputure.com Sales Contact: (86)0755-83285569-613
Documents / Resources
 |
Aputure Light torm [pdf] User Manual Light torm LS 300x |
