C27G4Z 27 Inch 280Hz Gaming Monitor
Safety
National Conventions
The following subsections describe national conventions used in this document.
Notes, Cautions, and Warnings
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are used as follows:
NOTE: A NOTE indicates important information that helps you make better use of your computer system.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
WARNING: A WARNING indicates the potential for bodily harm and tells you how to avoid the problem. Some warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specific presentation of the warning is mandated by regulatory authority.
Power
Installation
See below the recommended ventilation areas around the monitor when the monitor is installed on the wall or on the stand:
Installed with stand
Cleaning
Clean the cabinet regularly with a water-dampened, soft cloth.
When cleaning use a soft cotton or microfiber cloth. The cloth should be damp and almost dry, do not allow liquid into the case.
Please disconnect the power cord before cleaning the product.
Other
If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and contact a Service Center.
Make sure that the ventilating openings are not blocked by a table or curtain.
Do not engage the LCD monitor in severe vibration or high impact conditions during operation.
Do not knock or drop the monitor during operation or transportation.
The power cords shall be safety approved. For Germany, it shall be H03VV-F, 3G, 0.75 mm2, or better. For other countries, the suitable types shall be used accordingly.
Excessive sound pressure from earphones and headphones can cause hearing loss. Adjustment of the equalizer to maximum increases the earphones and headphones output voltage and therefore the sound pressure level.
Setup
Contents in Box *
✴ Not all signal cables will be provided for all countries and regions. Please check with the local dealer or AOC branch office for confirmation.
Set-up Stand & Base
Please setup or remove the base following the steps as below.
Setup:
Remove:
NOTE: Display design may differ from those illustrated.
Adjusting Viewing Angle
To achieve the best viewing experience, it is recommended that the user can make sure they are able to look at their whole face on the screen, then adjust the monitor’s angle based on personal preference. Hold the stand so you will not topple the monitor when you change the monitor’s angle. You are able to adjust the monitor as below:
NOTE:
Do not touch the LCD screen when you change the angle. Touching the LCD screen may cause damage.
Warning
- To avoid potential screen damage, such as panel peeling, ensure that the monitor does not tilt downward by more than -5 degrees.
- Do not press the screen while adjusting the angle of the monitor. Grasp only the bezel.
Connecting the Monitor
Cable Connections In Back of Monitor and Computer:
- DisplayPort
- HDMI
- Earphone
- Power
Connect to PC
1. Connect the power cord to the back of the display firmly.
2. Turn off your computer and unplug its power cable.
3. Connect the display signal cable to the video connector on the back of your computer.
4. Plug the power cord of your computer and your display into a nearby outlet. 5. Turn on your computer and display.
If your monitor displays an image, installation is complete. If it does not display an image, please refer to Troubleshoot.
To protect equipment, always turn off the PC and LCD monitor before connecting.
Wall Mounting
Preparing to Install An Optional Wall Mounting Arm.
This monitor can be attached to a wall mounting arm you purchase separately.
Disconnect power before this procedure. Follow these steps:
1. Remove the base.
2. Follow the manufacturer’s instructions to assemble the wall mounting arm.
3. Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the monitor.
4. Insert the 4 screws into the holes and tighten.
5. Reconnect the cables. Refer to the user’s manual that came with the optional wall mounting arm for instructions on attaching it to the wall.
Specification of wall hanger screws: M4*(10+X)mm (X=Thickness of Wall mount bracket) M=4.0Max
D3.86-3.96
M4-P0.7
Dk=8.0 H=2.0 L=10+X
Note: VESA mounting screw holes are not available for all models, please check with the dealer or official department of AOC. Always contact manufacturer for wall-mount installation.
* Display design may differ from those illustrated.
WARNING:
1. To avoid potential screen damage, such as panel peeling, ensure that the monitor does not tilt downward by more than -5 degrees.
2. Do not press the screen while adjusting the angle of the monitor. Grasp only the bezel.
Adaptive-Sync function
1. Adaptive-Sync function works with DP/HDMI
2. Compatible Graphics Card: Recommended list is as below, also could be checked by visiting www.AMD. com
Graphics Cards
• Radeon™ RX Vega series
• Radeon™ RX 500 series
• Radeon™ RX 400 series
• Radeon™ R9/R7 300 series (R9 370/X, R7 370/X, R7 265 except)
• Radeon™ Pro Duo (2016)
• Radeon™ R9 Nano series
• Radeon™ R9 Fury series
• Radeon™ R9/R7 200 series (R9 270/X, R9 280/X except)
Processors
• AMD Ryzen™ 7 2700U
• AMD Ryzen™ 5 2500U
• AMD Ryzen™ 5 2400G
• AMD Ryzen™ 3 2300U
• AMD Ryzen™ 3 2200G
• AMD PRO A12-9800
• AMD PRO A12-9800E
• AMD PRO A10-9700
• AMD PRO A10-9700E
• AMD PRO A8-9600
• AMD PRO A6-9500
• AMD PRO A6-9500E
• AMD PRO A12-8870
• AMD PRO A12-8870E
• AMD PRO A10-8770
• AMD PRO A10-8770E
• AMD PRO A10-8750B
• AMD PRO A8-8650B
• AMD PRO A6-8570
• AMD PRO A6-8570E
• AMD PRO A4-8350B
• AMD A10-7890K
• AMD A10-7870K
• AMD A10-7850K
• AMD A10-7800
• AMD A10-7700K
• AMD A8-7670K
• AMD A8-7650K
• AMD A8-7600
• AMD A6-7400K
HDR
It is compatible with input signals in HDR10 format.
The display may automatically activate the HDR function if the player and content are compatible. Please contact the device manufacturer and the content provider for information on the compatibility of your device and content. Please select “OFF” for the HDR function when you have no need for automatical activation function.
Note:
1. No special setting is needed for the DisplayPort/HDMI interface in WIN10 versions lower (older) than V1703.
2. Only the HDMI interface is available and the DisplayPort interface cannot function in WIN10 version V1703. 3. 3840×2160 only suggest for Blu-ray Player, Xbox and PlayStation.
a. The display resolution is set to 1920*1080, and HDR is preset to ON.
b. After entering an application, the best HDR effect can be achieved when the resolution is changed to 1920*1080 (if available).
Adjusting Hotkeys
|
1 |
Source/Exit |
|
2 |
Gaming Mode |
|
3 |
Dial Point |
|
4 |
Menu/Enter |
|
5 |
Power |
Menu/Enter
Press to display the OSD or confirm the selection.
Power
Press the Power button to turn on the monitor.
Dial Point
When there is no OSD, press Dial Point button to show / hide Dial Point.
Gaming Mode
When there is no OSD, press “ ” key to open Gaming mode function, then press “ ” or “ ” key to select Gaming mode (Standard, FPS, RTS, Racing, Gamer 1, Gamer 2 or Gamer 3) basing on the different game types.
Source/Exit
When the OSD is closed, press Source/Exit button will be Source hot key function.
When the OSD menu is active, this button acts as an exit key (to exit the OSD menu).
OSD Setting
Basic and simple instruction on the control keys.
INPUT SOURCE DP
1). Press the MENU-button to activate the OSD window.
2). Press or to navigate through the functions. Once the desired function is highlighted, press the MENU-button / OK to activate it, press or to navigate through the sub-menu functions. Once the desired sub-menu function is highlighted, press MENU-button / OK to activate it.
3). Press or to change the settings of the selected function. Press / to exit. If you want to adjust any other function, repeat steps 2-3.
4). OSD Lock Function: To lock the OSD, press and hold the MENU-button while the monitor is off and then press power button to turn the monitor on. To unlock the OSD – press and hold the MENU button while the monitor is off and then press power button to turn the monitor on.
Notes:
1). If the product has only one signal input, the item of “Input Select” is unable to be adjusted.
2). If the input signal resolution is the native resolution or Adaptive-Sync, then the item “Image Ratio” is invalid.
Game Setting
|
Gaming Mode |
Standard |
Enhance readability for suitable web and mobile games. |
|
FPS |
For playing FPS (first Person Shooters) games. Improves black level in dark theme. |
|
|
RTS |
For playing RTS (Real Time Strategy) games. Improves the image quality. |
|
|
Racing |
For playing Racing games, Provides fastest response time and high color saturation. |
|
|
Gamer 1 |
User’s preference settings saved as Gamer 1. |
|
|
Gamer 2 |
User’s preference settings saved as Gamer 2. |
|
|
Gamer 3 |
User’s preference settings saved as Gamer 3. |
|
|
Shadow Control |
0 ~ 20 |
Shadow Control Default is 0, then end-user can adjust from 0 to 20 increase for a clearer picture. If picture is too dark to be saw the detail clearly, adjusting from 0 to 20 for a clear picture. |
|
Low Input Lag |
Off / On |
Turn off frame buffer to decrease input lag. |
|
Game Color |
0 ~ 20 |
Game Color will provide 0-20 level for adjusting saturation to get a better picture. |
|
Adaptive-Sync |
Off / On |
Disable or Enable Adaptive-Sync. Adaptive-Sync Run Reminder: When the Adaptive-Sync feature is enabled, there may be flashing in some game environments. |
|
Dial Point |
Off / On / Dynamic |
The“Dial Point”function places an aiming indicator in the center of screen for helping gamers to play First Person Shooter (FPS) games with accurate and precise aiming. |
|
Sniper Scope |
Off / 1 / 1.5 / 2.0 |
Zoom in locally to make it easier to target when shooting. |
|
MBR |
0 ~ 20 |
MBR (Motion Blur Reduction) Provides 0-20 levels of adjustments to reduce motion blur. Note: 1. The MBR function can be adjusted when Adaptive-Sync is turned off, and the refresh rate ≥75Hz. 2. The brightness of the screen will decrease as the adjustment value increases. |
|
MBR Sync |
Off / On |
Disable or Enable MBR Sync (Motion Blur Remove). Note: The MBR Sync function can be adjusted when Adaptive-Sync is turned On, and the refresh rate ≥75Hz. |
|
Overdrive |
Normal |
Adjust the response time. Note: 1. If the user adjusts OverDrive to “Fastest” the displayed image may be blurred. Users can adjust the OverDrive level or turn it off according to their preferences. 2. The “Extreme” function is optional when Adaptive-Sync is turned off, and the refresh rate is ≥75Hz. 3. The screen brightness will decrease when the “Extreme”function is turned on. |
|
Fast |
||
|
Faster |
||
|
Fastest |
||
|
Extreme |
||
|
Frame Counter |
Off / Right-up / Right Down / Left-Up / Left Down |
Display V frequency on the corner selected. |
Note:
1). When “HDR Mode” under “Picture” is enable, the items “Gaming Mode”, “Shadow Control”, “Game Color”, cannot be adjusted.
2). When “HDR” under “Picture” is enable, the items “Gaming Mode”, “Shadow Control”, “Game Color”, “MBR” and “MBR Sync” can not be adjusted. “Extreme” under “Overdrive“ is not available.
3). When the “Color Space” under “Picture” is set to sRGB, the items “Shadow Control” and “Game Color” cannot be adjusted.
4). For the refresh rate below 120Hz (including 120Hz), “Sniper scope”, “low input lag”, “MBR” and “MBR Sync” are not available.
Picture
|
Brightness |
0-100 |
Backlight Adjustment. |
|
Contrast |
0-100 |
Contrast from Digital-register. |
|
Dark Boost |
Off / Level 1 / Level 2 / Level 3 |
Enhance the screen details in the dark or bright area to adjust the brightness in the bright area and ensure that it is not oversaturated. |
|
Gamma |
1.8 / 2.0 / 2.2 / 2.4 / 2.6 |
Adjust Gamma. |
|
Eco Adjustment |
Standard |
Standard Mode. |
|
Text |
Text Mode. |
|
|
Internet |
Internet Mode. |
|
|
Game |
Game Mode. |
|
|
Movie |
Movie Mode. |
|
|
Sports |
Sports Mode. |
|
|
Reading |
Reading Mode. |
|
|
Color Temp. |
Warm |
Recall Warm Color Temperature from EEPROM. |
|
Normal |
Recall Normal Color Temperature from EEPROM. |
|
|
Cool |
Recall Cool Color Temperature from EEPROM. |
|
|
User |
Restore Color Temperature from EEPROM. |
|
|
Red |
0-100 |
Red gain from Digital-register. |
|
Green |
0-100 |
Green gain from Digital-register. |
|
Blue |
0-100 |
Blue gain from Digital-register. |
|
HDR |
Off |
Set the HDR profile according to your usage requirements. Note: When HDR is detected, the HDR option is displayed for adjustment. |
|
DisplayHDR |
||
|
HDR Picture |
||
|
HDR Movie |
||
|
HDR Game |
||
|
HDR Mode |
Off |
Optimized for the color and contrast of the picture, which will simulate showing the HDR effect. Note: When HDR is not detected, the HDR Mode option is displayed for adjustment. |
|
HDR Picture |
||
|
HDR Movie |
||
|
HDR Game |
||
|
DCR |
Off |
Disable dynamic contrast ratio. |
|
On |
Enable dynamic contrast ratio. |
|
|
Color Space |
Panel Native |
Standard color space panel. |
|
sRGB |
sRGB Color space. |
|
|
LowBlue Mode |
Off |
Decrease blue light wave by controlling color temperature. |
|
Multimedia |
||
|
Internet |
||
|
Office |
||
|
Reading |
||
|
Image Ratio |
Full / Aspect / 1:1 / 17” (4:3) / 19” (4:3) / 19” (5:4) / 19”W (16:10) / 21.5”W (16:9)/ 22”W (16:10)/ 23”W (16:9) / 23.6”W (16:9) / 24”W (16:9) |
Select image ratio for display. |
Note:
1). When “HDR” is enable, all the items except “HDR“, ”Image Ratio” under “Picture” cannot be adjusted.
2). When “HDR Mode” is enable, all the items except “HDR Mode”, “Brightness”, “DCR”, ”Image Ratio” cannot be adjusted.
3). When the “Color Space” is set to sRGB, all the items except “Color Space”, “Brightness”, “DCR”, ”Image Ratio” cannot be adjusted.
4). When the “Eco Adjustment” is set to Reading, “Contrast”, ”Color Temp”, ”DCR”, ”Color Space”, ”Low blue mode” cannot be adjusted.
Settings
|
Language |
|
Select the OSD language. |
|
Input Select |
Auto / HDMI / DP |
Select Input Signal Source. |
|
Break Reminder |
Off / On |
Break reminder if the user continuously works for more than 1hrs. |
|
Off Timer |
0-24 hrs |
Select DC off time. |
|
DDC/CI |
No / Yes |
Turn On/Off DDC/CI Support. |
|
Reset |
No / Yes |
Reset the menu to default. |
Audio
|
Volume |
0-100 |
Volume Adjustment. |
|
Mute |
Off / On |
Mute the volume. |
OSD Setup
|
Transparence |
0-100 |
Adjust the transparence of OSD. |
|
H. Position |
0-100 |
Adjust the horizontal position of OSD. |
|
V. Position |
0-100 |
Adjust the vertical position of OSD. |
|
Timeout |
5-120 |
Adjust the OSD Timeout. |
Information
LED Indicator
|
Status |
LED Color |
|
Full Power Mode |
White |
|
Active-off Mode |
Orange |
Troubleshoot
|
Problem & Question |
Possible Solutions |
|
Power LED Is Not ON |
Make sure the power button is ON and the Power Cord is properly connected to a grounded power outlet and to the monitor. |
|
No image on the screen |
Check the power cord connection and power supply.
(Connected using the HDMI cable) Check the HDMI cable connection. (Connected using the DP cable) Check the DP cable connection. * HDMI/DP input is not available on every model.
If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows 7/8/10) and then change the frequency of the video card. (Refer to the Setting the Optimal Resolution) If the initial screen (the login screen) does not appear, contact the Service Center or your dealer.
You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly. Adjust the maximum resolution and frequency that the monitor can handle properly.
|
|
Picture Is Fuzzy & Has Ghosting Shadowing Problem |
Adjust the Contrast and Brightness Controls. Press hot-key (AUTO) to auto-adjust. Make sure you are not using an extension cable or switch box. We recommend plugging the monitor directly to the video card output connector on the back. |
|
Picture Bounces, Flickers Or Wave Pattern Appears In The Picture |
Move electrical devices that may cause electrical interference as far away from the monitor as possible. Use the maximum refresh rate your monitor is capable of at the resolution you are using. |
|
Monitor Is Stuck In Active Off-Mode” |
The Computer Power Switch should be in the ON position. The Computer Video Card should be snugly fitted in its slot. Make sure the monitor’s video cable is properly connected to the computer. Inspect the monitor’s video cable and make sure no pin is bent. Make sure your computer is operational by hitting the CAPS LOCK key on the keyboard while observing the CAPS LOCK LED. The LED should either turn ON or OFF after hitting the CAPS LOCK key. |
|
Missing one of the primary colors (RED, GREEN, or BLUE) |
Inspect the monitor’s video cable and make sure that no pin is damaged. Make sure the monitor’s video cable is properly connected to the computer. |
|
Screen image is not centered or sized properly |
Adjust H-Position and V-Position or press hot-key (AUTO). |
|
Picture has color defects (white does not look white) |
Adjust RGB color or select desired color temperature. |
|
Horizontal or vertical disturbances on the screen |
Use Windows 7/8/10/11 shut-down mode to adjust CLOCK and FOCUS. Press hot-key (AUTO) to auto-adjust. |
|
Regulation & Service |
Please refer to Regulation & Service Information which is in the CD manual or www.aoc.com (to find the model you purchase in your country and to find Regulation & Service Information in Support page. |
Specification
General Specification
|
Panel |
Model name |
C27G4Z |
||
|
Driving system |
TFT Color LCD |
|||
|
Viewable Image Size |
68.6 cm diagonal |
|||
|
Pixel pitch |
0.3114mm(H) x 0.3114mm(V) |
|||
|
Video |
HDMI lnterface & DP Interface |
|||
|
Display Color |
1.07B[1] |
|||
|
Others |
Horizontal scan range |
30k-280kHz(HDMI) 30k-320kHz(DP) |
||
|
Horizontal scan Size(Maximum) |
597.888mm |
|||
|
Vertical scan range |
48-240Hz(HDMI) 48-280Hz(DP) |
|||
|
Vertical Scan Size(Maximum) |
336.312mm |
|||
|
Optimal preset resolution |
1920X1080@60Hz |
|||
|
Max resolution |
1920×1080@240Hz(HDMI) 1920×1080@280Hz(DP) |
|||
|
Plug & Play |
VESA DDC2B/CI |
|||
|
Power Source |
100-240V~, 50/60Hz, 1.5A |
|||
|
Power Consumption |
Typical(default brightness and contrast) |
30W |
||
|
Max. (brightness = 100, contrast =100) |
≤44W |
|||
|
Standby Mode |
≤0.5W |
|||
|
Physical Characteristics |
Connector Type |
HDMI/DP/Earphone out |
||
|
Signal Cable Type |
Detachable |
|||
|
Environmental |
Temperature |
Operating |
0°C~40°C |
|
|
Non-Operating |
-25°C~55°C |
|||
|
Humidity |
Operating |
10%~85% (Non-Condensing) |
||
|
Non-Operating |
5%~93% (Non-Condensing) |
|||
|
Altitude |
Operating |
0m~5000m (0ft~16404ft) |
||
|
Non-Operating |
0m~12192m (0ft~40000ft) |
|||
[1] Note: The maximum number of display colors supported by this product is 1.07 billion, and the setting conditions are as follows (there may be differences due to the output limitation of some graphics cards):
|
Signal Version Color Format State Color Bit |
HDMI 2.1 |
DP 1.4 |
||
|
YCbCr422 YCbCr420 |
YCbCr444 RGB |
YCbCr422 YCbCr420 |
YCbCr444 RGB |
|
|
1920×1080 @ 280Hz 10bits |
NA |
NA |
OK |
NA |
|
1920×1080 @ 280Hz 8bits |
NA |
NA |
OK |
OK |
|
1920×1080 @ 240Hz 10bits |
NA |
NA |
OK |
OK |
|
1920×1080 @ 240Hz 8bits |
OK |
OK |
OK |
OK |
|
1920×1080 @ 144Hz 10bits |
OK |
NA |
NA |
NA |
|
1920×1080 @ 144Hz 8bits |
OK |
OK |
NA |
NA |
|
1920×1080 @ 120Hz 10bits |
OK |
OK |
OK |
OK |
|
1920×1080 @ 120Hz 8bits |
OK |
OK |
OK |
OK |
|
1920×1080 @ 60Hz 10bits |
OK |
OK |
OK |
OK |
|
1920×1080 @ 60Hz 8bits |
OK |
OK |
OK |
OK |
Preset Display Modes
|
STANDARD |
RESOLUTION(±1Hz) |
HORIZONTAL FREQUENCY(KHz) |
VERTICAL FREQUENCY(Hz) |
|
VGA |
640×480@60Hz |
31.469 |
59.940 |
|
640×480@67Hz |
35.000 |
66.667 |
|
|
640×480@72Hz |
37.861 |
72.809 |
|
|
640×480@75Hz |
37.500 |
75.000 |
|
|
640×480@100Hz |
51.082 |
99.769 |
|
|
640×480@120Hz |
61.910 |
119.518 |
|
|
SVGA |
800×600@56Hz |
35.156 |
56.250 |
|
800×600@60Hz |
37.879 |
60.317 |
|
|
800×600@72Hz |
48.077 |
72.188 |
|
|
800×600@75Hz |
46.875 |
75.000 |
|
|
800×600@100Hz |
63.684 |
99.662 |
|
|
800×600@120Hz |
77.425 |
119.854 |
|
|
XGA |
1024×768@60Hz |
48.363 |
60.004 |
|
1024×768@70Hz |
56.476 |
70.069 |
|
|
1024×768@75Hz |
60.023 |
75.029 |
|
|
1024×768@100Hz |
81.577 |
99.972 |
|
|
1024×768@120Hz |
97.551 |
119.989 |
|
|
SXGA |
1280×1024@60Hz |
63.981 |
60.020 |
|
1280×1024@75Hz |
79.976 |
75.025 |
|
|
FHD |
1920×1080@60Hz |
67.500 |
60.000 |
|
1920×1080@120Hz |
137.284 |
120.003 |
|
|
FHD(HDMI) |
1920×1080@144Hz |
162.004 |
144.003 |
|
FHD |
1920×1080@240Hz |
274.563 |
240.002 |
|
FHD(DP) |
1920×1080@280Hz |
310.803 |
280.003 |
|
SVGA MAC |
832×624@75Hz |
49.725 |
74.550 |
|
DOS |
720×400@70Hz |
31.469 |
70.087 |
Note: According to the VESA standard, there may be a certain error (+/-1Hz) when calculating the refresh rate (field frequency) of different operating systems and graphics cards. In order to improve compatibility, the nominal refresh rate of this product has been rounded off. Please refer to the actual product.
Pin Assignments
19-Pin Color Display Signal Cable
|
Pin No. |
Signal Name |
Pin No. |
Signal Name |
Pin No. |
Signal Name |
|
1. |
TMDS Data 2+ |
9. |
TMDS Data 0- |
17. |
DDC/CEC Ground |
|
2. |
TMDS Data 2 Shield |
10. |
TMDS Clock + |
18. |
+5V Power |
|
3. |
TMDS Data 2- |
11. |
TMDS Clock Shield |
19. |
Hot Plug Detect |
|
4. |
TMDS Data 1+ |
12. |
TMDS Clock |
|
|
|
5. |
TMDS Data 1Shield |
13. |
CEC |
|
|
|
6. |
TMDS Data 1- |
14. |
Reserved (N.C. on device) |
|
|
|
7. |
TMDS Data 0+ |
15. |
SCL |
|
|
|
8. |
TMDS Data 0 Shield |
16. |
SDA |
|
|
20-Pin Color Display Signal Cable
|
Pin No. |
Signal Name |
Pin No. |
Signal Name |
|
1 |
ML_Lane 3 (n) |
11 |
GND |
|
2 |
GND |
12 |
ML_Lane 0 (p) |
|
3 |
ML_Lane 3 (p) |
13 |
CONFIG1 |
|
4 |
ML_Lane 2 (n) |
14 |
CONFIG2 |
|
5 |
GND |
15 |
AUX_CH(p) |
|
6 |
ML_Lane 2 (p) |
16 |
GND |
|
7 |
ML_Lane 1 (n) |
17 |
AUX_CH(n) |
|
8 |
GND |
18 |
Hot Plug Detect |
|
9 |
ML_Lane 1 (p) |
19 |
Return DP_PWR |
|
10 |
ML_Lane 0 (n) |
20 |
DP_PWR |
Plug and Play
Plug & Play DDC2B Feature
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.
The DDC2B is a bi-directional data channel based on the I2C protocol. The host can request EDID information over the DDC2B channel.
Documents / Resources
 |
AOC C27G4Z 27 Inch 280Hz Gaming Monitor [pdf] User Manual C27G4Z 27 Inch 280Hz Gaming Monitor, C27G4Z, 27 Inch 280Hz Gaming Monitor, 280Hz Gaming Monitor, Gaming Monitor |
